Gentle nudge. I haven't seen this or any of my other patches make it
into linux-next yet. I was hoping we could get them all in, so I can
start testing some other features of linux-next with some of these
patches.
Thanks,
adam
On Fri, Jan 8, 2016 at 11:50 PM, Adam Ford <aford173@xxxxxxxxx> wrote:
> The Logic PD Torpedo standard kits come with a SOM populated to us an
> 8-bit parallel camera interface. This patch pin muxes the omap3-isp
> pins, sets the MT9P031 clicks, and configures the i2c2 bus to communicate
> with the mt9p031 on address 0x48.
>
> I have not done a lot of testing, but when modprobing
> mt9p031, then omap3-isp, the board responds with
> MT9P031 detected at address 0x48.
>
> Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> ---
> arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 53 +++++++++++++++++++++++
> 1 file changed, 53 insertions(+)
>
> diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
> index fb13f18..60831b8 100644
> --- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
> +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
> @@ -217,6 +217,24 @@
> >;
> };
>
> + isp_pins: pinmux_isp_pins {
> + pinctrl-single,pins = <
> + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */
> + OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */
> + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */
> + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */
> +
> + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */
> + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */
> + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */
> + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */
> + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */
> + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */
> + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */
> + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */
> + >;
> + };
> +
> dss_dpi_pins1: pinmux_dss_dpi_pins1 {
> pinctrl-single,pins = <
> OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
> @@ -268,6 +286,24 @@
> };
> };
>
> +&i2c2 {
> + mt9p031@48 {
> + compatible = "aptina,mt9p031";
> + reg = <0x48>;
> + clocks = <&isp 0>;
> + vaa-supply = <&vaux4>;
> + vdd-supply = <&vaux4>;
> + vdd_io-supply = <&vaux4>;
> + port {
> + mt9p031_out: endpoint {
> + input-clock-frequency = <24000000>;
> + pixel-clock-frequency = <72000000>;
> + remote-endpoint = <&ccdc_ep>;
> + };
> + };
> + };
> +};
> +
> &i2c3 {
> touchscreen: tsc2004@48 {
> compatible = "ti,tsc2004";
> @@ -289,6 +325,23 @@
> };
> };
>
> +&isp {
> + pinctrl-names = "default";
> + pinctrl-0 = <&isp_pins>;
> + ports {
> + port@0 {
> + reg = <0>;
> + ccdc_ep: endpoint {
> + remote-endpoint = <&mt9p031_out>;
> + bus-width = <8>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + pclk-sample = <0>;
> + };
> + };
> + };
> +};
> +
> &uart1 {
> interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
> };
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
