[PATCH v5 1/4] ARM: dts: am335x-bone: add support for beaglebone NAND cape

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Beaglebone Board can be connected to expansion boards to add devices to them.
These expansion boards are called 'capes'. This patch adds support for
following versions of Beaglebone(AM335x) NAND capes
(a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64
(b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224
Further information and datasheets can be found at [1] and [2]

* How to boot from NAND using Memory Expander + NAND Cape ? *
 - Important: As BOOTSEL values are sampled only at POR, so after changing any
   setting on SW2 (DIP switch), disconnect and reconnect all board power supply
   (including mini-USB console port) to POR the beaglebone.

 - Selection of ECC scheme
  for NAND cape(a), ROM code expects BCH8_HW ecc-scheme
  for NAND cape(b), ROM code expects BCH16_HW ecc-scheme

 - Selection of boot modes can be controlled via  DIP switch(SW2) present on
   Memory Expander cape, so first boot via MMC or other sources to flash NAND
   device and then switch to SW2[SWITCH_BOOT]=ON to boot from NAND Cape.
   SW2[SWITCH_BOOT] == OFF  follow default boot order  MMC-> SPI -> UART -> USB
   SW2[SWITCH_BOOT] == ON   boot mode selected via DIP switch(SW2)

 - For NAND boot following switch settings need to be followed
   SW2[ 0] = ON   (SYSBOOT[ 0]==0: NAND boot mode selected )
   SW2[ 1] = ON   (SYSBOOT[ 1]==0:       -- do --          )
   SW2[ 2] = OFF  (SYSBOOT[ 2]==1:       -- do --          )
   SW2[ 3] = OFF  (SYSBOOT[ 3]==1:       -- do --          )
   SW2[ 4] = ON   (SYSBOOT[ 4]==0:       -- do --          )
   SW2[ 8] = OFF  (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device )
   SW2[ 9] = ON   (SYSBOOT[ 9]==0: ECC done by ROM  )
   SW2[10] = ON   (SYSBOOT[10]==0: Non Muxed device )
   SW2[11] = ON   (SYSBOOT[11]==0:    -- do --      )

[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion
[2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module

Signed-off-by: Pekon Gupta <pekon@xxxxxx>
---
 arch/arm/boot/dts/am335x-bone-memory-cape.dts | 130 ++++++++++++++++++++++++++
 arch/arm/boot/dts/am335x-bone.dts             |   1 +
 arch/arm/boot/dts/am335x-boneblack.dts        |   1 +
 3 files changed, 132 insertions(+)
 create mode 100644 arch/arm/boot/dts/am335x-bone-memory-cape.dts

diff --git a/arch/arm/boot/dts/am335x-bone-memory-cape.dts b/arch/arm/boot/dts/am335x-bone-memory-cape.dts
new file mode 100644
index 0000000..d6cb9ff
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bone-memory-cape.dts
@@ -0,0 +1,130 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This DTS adds supports for capes using GPMC interface to connect external
+ * memory like NAND, NOR Flash to Beaglebone-LT (white) and Beaglebone-Black.
+ */
+
+
+&am33xx_pinmux {
+	nand_flash_x16: nand_flash_x16 {
+		pinctrl-single,pins = <
+			0x00 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad0.gpmc_ad0 */
+			0x04 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad1.gpmc_ad1 */
+			0x08 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad2.gpmc_ad2 */
+			0x0c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad7.gpmc_ad7 */
+			0x20 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad8.gpmc_ad8 */
+			0x24 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad9.gpmc_ad9 */
+			0x28 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad10.gpmc_ad10 */
+			0x2c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad11.gpmc_ad11 */
+			0x30 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad12.gpmc_ad12 */
+			0x34 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad13.gpmc_ad13 */
+			0x38 (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad14.gpmc_ad14 */
+			0x3c (MUX_MODE0 | PIN_INPUT)	/* gpmc_ad15.gpmc_ad15 */
+			0x70 (MUX_MODE0 | PIN_INPUT_PULLUP )	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (MUX_MODE7 | PIN_OUTPUT_PULLUP)	/* gpmc_wpn.gpio0_30 */
+			0x7c (MUX_MODE0 | PIN_OUTPUT_PULLUP)	/* gpmc_csn0.gpmc_csn0  */
+			0x90 (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_wen.gpmc_wen */
+			0x9c (MUX_MODE0 | PIN_OUTPUT)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+};
+
+&elm {
+     status = "disabled";
+};
+
+&gpmc {
+     status = "disabled";
+};
+
+&gpmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x16>;
+	ranges = <0 0 0 0x01000000>;	/* CS0: min address-space configurable under GPMC chip-select = 16MB*/
+	nand@0,0 {
+		reg = <0 0 0x380>; /* CS0, offset=0x0, GPMC register-space size=0x380 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <16>;
+		gpmc,device-width = <2>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <80>;
+		gpmc,cs-wr-off-ns = <80>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <80>;
+		gpmc,adv-wr-off-ns = <80>;
+		gpmc,we-on-ns = <20>;
+		gpmc,we-off-ns = <60>;
+		gpmc,oe-on-ns = <20>;
+		gpmc,oe-off-ns = <60>;
+		gpmc,access-ns = <40>;
+		gpmc,rd-cycle-ns = <80>;
+		gpmc,wr-cycle-ns = <80>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000c0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002c0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00a00000 0x1f600000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
index 94ee427..f16bfcf 100644
--- a/arch/arm/boot/dts/am335x-bone.dts
+++ b/arch/arm/boot/dts/am335x-bone.dts
@@ -9,6 +9,7 @@
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+#include "am335x-bone-memory-cape.dts"
 
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index 6b71ad9..c030b24 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -9,6 +9,7 @@
 
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
+#include "am335x-bone-memory-cape.dts"
 
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;
-- 
1.8.5.1.163.gd7aced9

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux