Re: MUSB not workin in .27rc6, was: Re: OMAP support in mainline?

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Sep 19, 2008 at 06:09:04PM +0200, Koen Kooi wrote:
>
> Op 18 sep 2008, om 11:55 heeft Felipe Balbi het volgende geschreven:
>
>> On Wed, Sep 17, 2008 at 03:23:49PM +0200, ext Koen Kooi wrote:
>>>
>>> Op 17 sep 2008, om 14:24 heeft Steve Sakoman het volgende geschreven:
>>>
>>>> On Wed, Sep 17, 2008 at 12:16 AM, Koen Kooi 
>>>> <k.kooi@xxxxxxxxxxxxxxxxxx>
>>>> wrote:
>>>>
>>>>> And they aren't working too well with current l-o git either with 
>>>>> MUSB
>>>>> being
>>>>> broken. There's a patch to fix client mode, but host mode still  
>>>>> isn't
>>>>> working.
>>>>
>>>> Host mode musb is working just fine on Overo with the "set
>>>> transceiver" patch.  Not sure why you are having trouble with Beagle
>>>> (and can't check since I don't have my Beagle board with me at the
>>>> moment)
>>>
>>> I should clarify: OTG mode with a host cable doesn't work in .27rc,  
>>> it does
>>> work in 2.6.26. I haven't tried specifying pure hostmode, only OTG.
>>> I would try it on the evm as well, but that is having serious irq  
>>> issues
>>> with .27rc, pressing a key on the keypad triggers an irq overrun,  
>>> ethernet
>>> gives an oops on boot when trying to register and irq etc,etc.  
>>> 2.6.27 is
>>> looking really, really bad on omap3 at the moment.
>>
>> Yeah, we lost some musb history when it went to mainline. I didn't  
>> test
>> this patch yet cuz I've been quite busy at work, but it should make
>> beagle work. Could you tell me if makes it work ?
>>
>> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
>> index 9d2dcb1..f7fe91e 100644
>> --- a/drivers/usb/musb/omap2430.c
>> +++ b/drivers/usb/musb/omap2430.c
>> @@ -215,12 +215,14 @@ void musb_platform_set_mode(struct musb *musb,  
>> u8 musb_mode)
>>
>> int __init musb_platform_init(struct musb *musb)
>> {
>> +       struct otg_transceiver *xceiv = otg_get_transceiver();
>>        u32 l;
>>
>> #if defined(CONFIG_ARCH_OMAP2430)
>>        omap_cfg_reg(AE5_2430_USB0HS_STP);
>> #endif
>>
>> +       memcpy(musb->xceiv, xceiv, sizeof(*xceiv));
>>        musb_platform_resume(musb);
>>
>>        l = omap_readl(OTG_SYSCONFIG);
>
> Ok, another datapoint: client mode (tested on beagle by Måns) and host  
> mode (tested on overo by Steve) work with a similar patch as above, OTG 
> mode is broken (tested on beagle and evm by me).

I don't recall having otg (id pin handling) working on omap3. I have
some experimental patches on my local branch (they work, but need
clean up).

-- 
balbi
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux