On 9/28/2018 2:16 AM, Rob Herring wrote:
On Thu, Sep 20, 2018 at 04:50:48PM +0800, Jianxin Pan wrote:
From: Liang Yang <liang.yang@xxxxxxxxxxx>
Add Amlogic NAND controller dt-bindings for Meson SoC,
Current this driver support GXBB/GXL/AXG platform.
Signed-off-by: Liang Yang <liang.yang@xxxxxxxxxxx>
Signed-off-by: Yixun Lan <yixun.lan@xxxxxxxxxxx>
---
.../devicetree/bindings/mtd/amlogic,meson-nand.txt | 60 ++++++++++++++++++++++
1 file changed, 60 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
diff --git a/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
new file mode 100644
index 0000000..803df2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/amlogic,meson-nand.txt
@@ -0,0 +1,60 @@
+Amlogic NAND Flash Controller (NFC) for GXBB/GXL/AXG family SoCs
+
+This file documents the properties in addition to those available in
+the MTD NAND bindings.
+
+Required properties:
+- compatible : contains one of:
+ - "amlogic,meson-gxl-nfc"
+ - "amlogic,meson-axg-nfc"
+- clocks :
+ A list of phandle + clock-specifier pairs for the clocks listed
+ in clock-names.
+
+- clock-names: Should contain the following:
+ "core" - NFC module gate clock
+ "device" - device clock from eMMC sub clock controller
+
+- amlogic,mmc-syscon : Required for NAND clocks, it's shared with SD/eMMC
+ controller port C
+
+Optional children nodes:
+Children nodes represent the available nand chips.
+
+Other properties:
+see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings.
+
+Example demonstrate on AXG SoC:
+
+ sd_emmc_c_clkc: mmc@7000 {
+ compatible = "amlogic,meson-axg-mmc-clkc", "syscon";
+ reg = <0x0 0x7000 0x0 0x800>;
+ status = "okay";
+ };
+
+ nand: nfc@7800 {
nand-controller@7800
ok, i will fix it.
+ compatible = "amlogic,meson-axg-nfc";
+ reg = <0x0 0x7800 0x0 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+
+ clocks = <&clkc CLKID_SD_EMMC_C>,
+ <&sd_emmc_c_clkc CLKID_MMC_DIV>;
+ clock-names = "core", "device";
+ amlogic,mmc-syscon = <&sd_emmc_c_clkc>;
+
+ status = "okay";
Don't show status in examples, plus you have it twice.
ok, i will fix it.
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_pins>;
+
+ nand@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nand-on-flash-bbt;
+ };
+ };
--
1.9.1
.
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
