On Fri, Oct 18, 2013 at 07:42:35PM +0800, Shawn Guo wrote:
> On Fri, Oct 18, 2013 at 06:54:18PM +0800, Dong Aisheng wrote:
> > The DLL(Delay Line) is newly added to assist in sampling read data.
> > The DLL provides the ability to programmatically select a quantized
> > delay (in fractions of the clock period) regardless of on-chip variations
> > such as process, voltage and temperature (PVT).
> >
> > This patch adds a user interface to set slave delay line via device tree.
> > It's usually used in high speed mode like mmc DDR mode when the signal
> > quality is not good caused by board design, e.g. the signal path is too long.
> > User can manual set delay line to find a suitable data sampling window
> > for card to work properly.
> >
> > Signed-off-by: Dong Aisheng <b29396@xxxxxxxxxxxxx>
> > ---
> > .../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 5 +++++
> > drivers/mmc/host/sdhci-esdhc-imx.c | 18 ++++++++++++++++++
> > include/linux/platform_data/mmc-esdhc-imx.h | 1 +
> > 3 files changed, 24 insertions(+), 0 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> > index 1dd6225..78a45c5 100644
> > --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> > +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> > @@ -12,6 +12,11 @@ Required properties:
> > Optional properties:
> > - fsl,cd-controller : Indicate to use controller internal card detection
> > - fsl,wp-controller : Indicate to use controller internal write protection
> > +- fsl,delay-line : Specify the number of delay cells for override mode.
> > + This is used to set the clock delay for DLL(Delay Line) on override mode
> > + to select a proper data sampling window in case the clock quality is not good
> > + due to signal path is too long on the board.
> > + please refer to DLL chapter in RM for details.
>
> It might be better to reword it like:
>
> Please refer to eSDHC/uSDHC DLL_CTRL register bit field
> DLL_CTRL_SLV_OVERRIDE_VAL in Reference Manual for details.
>
There is a DLL (Delay Line) chapter in the reference manual which
has more detailed descriptions on the delay line including override mode.
So i think it may be better to point user to the DLL chapter for understanding,
then naturally user will refer to register for bit defines later too.
Does it make sense?
Regards
Dong Aisheng
> >
> > Examples:
> >
> > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> > index c5c26bd..87d202b 100644
> > --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> > @@ -46,6 +46,11 @@
> > /* Bits 3 and 6 are not SDHCI standard definitions */
> > #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
> >
> > +/* dll control register */
> > +#define ESDHC_DLL_CTRL 0x60
> > +#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
> > +#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
> > +
> > /* tune control register */
> > #define ESDHC_TUNE_CTRL_STATUS 0x68
> > #define ESDHC_TUNE_CTRL_STEP 1
> > @@ -817,6 +822,7 @@ static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
> > {
> > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > struct pltfm_imx_data *imx_data = pltfm_host->priv;
> > + struct esdhc_platform_data *boarddata = &imx_data->boarddata;
> >
> > switch (uhs) {
> > case MMC_TIMING_UHS_SDR12:
> > @@ -837,6 +843,15 @@ static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
> > ESDHC_MIX_CTRL_DDREN,
> > host->ioaddr + ESDHC_MIX_CTRL);
> > imx_data->is_ddr = 1;
> > + if (boarddata->delay_line) {
> > + u32 v;
> > + v = boarddata->delay_line <<
> > + ESDHC_DLL_OVERRIDE_VAL_SHIFT |
> > + (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
> > + if (is_imx53_esdhc(imx_data))
> > + v <<= 1;
> > + writel(v, host->ioaddr + ESDHC_DLL_CTRL);
> > + }
> > break;
> > }
> >
> > @@ -901,6 +916,9 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
> > else
> > boarddata->support_vsel = true;
> >
> > + if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
> > + boarddata->delay_line = 0;
> > +
> > return 0;
> > }
> > #else
> > diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h
> > index a0f5a8f..75f70f6 100644
> > --- a/include/linux/platform_data/mmc-esdhc-imx.h
> > +++ b/include/linux/platform_data/mmc-esdhc-imx.h
> > @@ -45,5 +45,6 @@ struct esdhc_platform_data {
> > int max_bus_width;
> > unsigned int f_max;
> > bool support_vsel;
> > + unsigned int delay_line;
> > };
> > #endif /* __ASM_ARCH_IMX_ESDHC_H */
> > --
> > 1.7.2.rc3
> >
> >
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
