On Fri, Oct 18, 2013 at 06:54:18PM +0800, Dong Aisheng wrote:
> The DLL(Delay Line) is newly added to assist in sampling read data.
> The DLL provides the ability to programmatically select a quantized
> delay (in fractions of the clock period) regardless of on-chip variations
> such as process, voltage and temperature (PVT).
>
> This patch adds a user interface to set slave delay line via device tree.
> It's usually used in high speed mode like mmc DDR mode when the signal
> quality is not good caused by board design, e.g. the signal path is too long.
> User can manual set delay line to find a suitable data sampling window
> for card to work properly.
>
> Signed-off-by: Dong Aisheng <b29396@xxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 5 +++++
> drivers/mmc/host/sdhci-esdhc-imx.c | 18 ++++++++++++++++++
> include/linux/platform_data/mmc-esdhc-imx.h | 1 +
> 3 files changed, 24 insertions(+), 0 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> index 1dd6225..78a45c5 100644
> --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
> @@ -12,6 +12,11 @@ Required properties:
> Optional properties:
> - fsl,cd-controller : Indicate to use controller internal card detection
> - fsl,wp-controller : Indicate to use controller internal write protection
> +- fsl,delay-line : Specify the number of delay cells for override mode.
> + This is used to set the clock delay for DLL(Delay Line) on override mode
> + to select a proper data sampling window in case the clock quality is not good
> + due to signal path is too long on the board.
> + please refer to DLL chapter in RM for details.
It might be better to reword it like:
Please refer to eSDHC/uSDHC DLL_CTRL register bit field
DLL_CTRL_SLV_OVERRIDE_VAL in Reference Manual for details.
>
> Examples:
>
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index c5c26bd..87d202b 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -46,6 +46,11 @@
> /* Bits 3 and 6 are not SDHCI standard definitions */
> #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
>
> +/* dll control register */
> +#define ESDHC_DLL_CTRL 0x60
> +#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
> +#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
> +
> /* tune control register */
> #define ESDHC_TUNE_CTRL_STATUS 0x68
> #define ESDHC_TUNE_CTRL_STEP 1
> @@ -817,6 +822,7 @@ static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
> {
> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> struct pltfm_imx_data *imx_data = pltfm_host->priv;
> + struct esdhc_platform_data *boarddata = &imx_data->boarddata;
>
> switch (uhs) {
> case MMC_TIMING_UHS_SDR12:
> @@ -837,6 +843,15 @@ static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
> ESDHC_MIX_CTRL_DDREN,
> host->ioaddr + ESDHC_MIX_CTRL);
> imx_data->is_ddr = 1;
> + if (boarddata->delay_line) {
> + u32 v;
> + v = boarddata->delay_line <<
> + ESDHC_DLL_OVERRIDE_VAL_SHIFT |
> + (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
> + if (is_imx53_esdhc(imx_data))
> + v <<= 1;
> + writel(v, host->ioaddr + ESDHC_DLL_CTRL);
> + }
> break;
> }
>
> @@ -901,6 +916,9 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
> else
> boarddata->support_vsel = true;
>
> + if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
> + boarddata->delay_line = 0;
> +
> return 0;
> }
> #else
> diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h
> index a0f5a8f..75f70f6 100644
> --- a/include/linux/platform_data/mmc-esdhc-imx.h
> +++ b/include/linux/platform_data/mmc-esdhc-imx.h
> @@ -45,5 +45,6 @@ struct esdhc_platform_data {
> int max_bus_width;
> unsigned int f_max;
> bool support_vsel;
> + unsigned int delay_line;
> };
> #endif /* __ASM_ARCH_IMX_ESDHC_H */
> --
> 1.7.2.rc3
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
