Hi Neil,
> Am 03.03.2022 um 17:30 schrieb H. Nikolaus Schaller <hns@xxxxxxxxxxxxx>:
>
> Hi Neil,
>
>> Am 03.03.2022 um 17:23 schrieb Neil Armstrong <narmstrong@xxxxxxxxxxxx>:
>>
>> Hi,
>>
>> On 26/02/2022 18:12, H. Nikolaus Schaller wrote:
>>> so that specialization drivers like ingenic-dw-hdmi can enable polling.
>>> Signed-off-by: H. Nikolaus Schaller <hns@xxxxxxxxxxxxx>
>>> ---
>>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 9 +++++++++
>>> include/drm/bridge/dw_hdmi.h | 1 +
>>> 2 files changed, 10 insertions(+)
>>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>>> index 4befc104d2200..43e375da131e8 100644
>>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>>> @@ -3217,6 +3217,15 @@ static int dw_hdmi_parse_dt(struct dw_hdmi *hdmi)
>>> return 0;
>>> }
>>> +void dw_hdmi_enable_poll(struct dw_hdmi *hdmi, bool enable)
>>> +{
>>> + if (hdmi->bridge.dev)
>>> + hdmi->bridge.dev->mode_config.poll_enabled = enable;
>>> + else
>>> + dev_warn(hdmi->dev, "no hdmi->bridge.dev");
>>> +}
>>> +EXPORT_SYMBOL_GPL(dw_hdmi_enable_poll);
>>> +
>>> struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
>>> const struct dw_hdmi_plat_data *plat_data)
>>> {
>>> diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
>>> index 2a1f85f9a8a3f..963960794b40e 100644
>>> --- a/include/drm/bridge/dw_hdmi.h
>>> +++ b/include/drm/bridge/dw_hdmi.h
>>> @@ -196,5 +196,6 @@ enum drm_connector_status dw_hdmi_phy_read_hpd(struct dw_hdmi *hdmi,
>>> void dw_hdmi_phy_update_hpd(struct dw_hdmi *hdmi, void *data,
>>> bool force, bool disabled, bool rxsense);
>>> void dw_hdmi_phy_setup_hpd(struct dw_hdmi *hdmi, void *data);
>>> +void dw_hdmi_enable_poll(struct dw_hdmi *hdmi, bool enable);
>>> #endif /* __IMX_HDMI_H__ */
>>
>> As I understand, this is because the IRQ line of the dw-hdmi IP isn't connected right ? and you use the display-connector ddc gpio instead ?
>
> Yes. The IRQ line is not connected on all boards as far as I can see.
>
>>
>> In this case I think the Ingenic DRM core should call drm_kms_helper_poll_init(drm) instead.
>
> Ah, that is good. it seems to do "dw_hdmi_enable_poll()" in a more generic way.
Well, I looked through source code and it is defined as
void drm_kms_helper_poll_init(struct drm_device *dev)
But there is no direct pointer to some drm_device available.
Neither in dw-hdmi nor ingenic-dw-hdmi.
What should the parameter to drm_kms_helper_poll_init(drm) be?
