Am 18.02.2013 23:36, schrieb Mr Goldcove: > I've only tried composite video input. > The video/ audio output is good. > > It has the following input: > RCA stereo sound > RCA video > S-video > > It has no push button but has a green led which illuminates when the > device is in use. Ok, could you please post the output of "lsusb -v -d eb1a:2861" ? Regards, Frank > > On 18. feb. 2013 22:25, Frank Schäfer wrote: >> Am 18.02.2013 21:53, schrieb Mr Goldcove: >>> "Easy Cap DC-60++" >>> Wrongly identified as card 19 "EM2860/SAA711X Reference Design", >>> resulting in no audio. >>> Works perfectly when using card 64 "Easy Cap Capture DC-60" >> Video inputs work fine, right ? >> Does this device has any buttons / LEDs ? >> >> The driver doesn't handle devices with generic IDs very well. >> In this case we can conclude from the USB PID that the device has audio >> support (which is actually the only difference to board >> EM2860_BOARD_SAA711X_REFERENCE_DESIGN). >> But I would like to think twice about it, because this kind of changes >> has very a high potential to cause regressions for other boards... >> >> Regards, >> Frank >> >>> **Interim solution** >>> load module (before inserting the EasyCap. I'm having trouble if the >>> module is loaded/unloaded with different cards...) >>> modprobe em28xx card=64 >>> or >>> add "options em28xx card=64" to /etc/modprobe.d/local.conf >>> >>> **hw info** >>> Bus 002 Device 005: ID eb1a:2861 eMPIA Technology, Inc. >>> >>> Chips: >>> Empia EM2860 P7JY8-011 201023-01AG >>> NXP SAA7113H >>> RMC ALC653 89G06K1 G909A >>> >>> **logs** >>> [ 5567.367883] em28xx: New device @ 480 Mbps (eb1a:2861, interface 0, >>> class 0) >>> [ 5567.367985] em28xx #0: chip ID is em2860 >>> [ 5567.380645] IR MCE Keyboard/mouse protocol handler initialized >>> [ 5567.384202] lirc_dev: IR Remote Control driver registered, major 249 >>> [ 5567.385468] IR LIRC bridge handler initialized >>> [ 5567.460386] em28xx #0: board has no eeprom >>> [ 5567.534612] em28xx #0: found i2c device @ 0x4a [saa7113h] >>> [ 5567.568303] em28xx #0: Your board has no unique USB ID. >>> [ 5567.568308] em28xx #0: A hint were successfully done, based on i2c >>> devicelist hash. >>> [ 5567.568312] em28xx #0: This method is not 100% failproof. >>> [ 5567.568314] em28xx #0: If the board were missdetected, please email >>> this log to: >>> [ 5567.568317] em28xx #0: V4L Mailing List >>> <linux-media@xxxxxxxxxxxxxxx> >>> [ 5567.568321] em28xx #0: Board detected as EM2860/SAA711X Reference Design >>> [ 5567.647433] em28xx #0: Identified as EM2860/SAA711X Reference Design >>> (card=19) >>> [ 5567.647438] em28xx #0: Registering snapshot button... >>> [ 5567.647531] input: em28xx snapshot button as >>> /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/input/input11 >>> [ 5568.019310] saa7115 15-0025: saa7113 found (1f7113d0e100000) @ 0x4a >>> (em28xx #0) >>> [ 5568.789385] em28xx #0: Config register raw data: 0x10 >>> [ 5568.813055] em28xx #0: AC97 vendor ID = 0x414c4761 >>> [ 5568.825074] em28xx #0: AC97 features = 0x0000 >>> [ 5568.825078] em28xx #0: Unknown AC97 audio processor detected! >>> [ 5569.284137] em28xx #0: v4l2 driver version 0.1.3 >>> [ 5570.305831] em28xx #0: V4L2 video device registered as video1 >>> [ 5570.305835] em28xx #0: V4L2 VBI device registered as vbi0 >>> [ 5570.305862] em28xx audio device (eb1a:2861): interface 1, class 1 >>> [ 5570.305877] em28xx audio device (eb1a:2861): interface 2, class 1 >>> [ 5570.305906] usbcore: registered new interface driver em28xx >>> [ 5570.305909] em28xx driver loaded >>> [ 5570.392917] usbcore: registered new interface driver snd-usb-audio >>> [ 7903.785365] em28xx #0: vidioc_s_fmt_vid_cap queue busy >>> -- >>> To unsubscribe from this list: send the line "unsubscribe linux-media" in >>> the body of a message to majordomo@xxxxxxxxxxxxxxx >>> More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
