2011/8/11 Josu Lazkano <josu.lazkano@xxxxxxxxx>: > Hello list, I just bought a Tevii S660 DVB-S2 USb tunner and I have > some problems with it. I already has the Tevii S470 card and it works > great with this configuration: > > mkdir /usr/local/src/dvb > cd /usr/local/src/dvb > wget http://tevii.com/100315_Beta_linux_tevii_ds3000.rar > unrar x 100315_Beta_linux_tevii_ds3000.rar > cp *.fw /lib/firmware > tar xjvf linux-tevii-ds3000.tar.bz2 > cd linux-tevii-ds3000 > make && make install > > I am using Debian Squeeze with stable kernel: 2.6.32-5-686 > > I configured the modprobe this way: > > # cat /etc/modprobe.d/options.conf > #Tevii S470 > options cx23885 adapter_nr=7 > #Tevii S660 > options dvb-usb-dw2102 adapter_nr=6 > #Disable the IR > options dvb-usb disable_rc_polling=1 > > At first time it works well, I just pluged it and it creates a dvb > device on /dev/dvb/adapter6 and the dmesg is correct (I have not a > copy of the message). I didn't try yet to watch any channel (I am > uusing MythTV). > > I reboot the machine and there are some USB error on the boot > secuence, something like this: > > ... device descriptor read/64, error -110 > > (Here is a photo of the screen: http://i53.tinypic.com/2u3z5s0.jpg) > > After a long boot, I execute the dmesg and this is what I get: > > [ 145.909045] usb 4-2: device descriptor read/64, error -110 > [ 146.189073] usb 4-2: new full speed USB device using ohci_hcd and address 5 > [ 151.208761] usb 4-2: device descriptor read/8, error -110 > [ 156.329684] usb 4-2: device descriptor read/8, error -110 > [ 156.612043] usb 4-2: new full speed USB device using ohci_hcd and address 6 > [ 161.636610] usb 4-2: device descriptor read/8, error -110 > [ 166.756544] usb 4-2: device descriptor read/8, error -110 > [ 166.864081] hub 4-0:1.0: unable to enumerate USB device on port 2 > > And there is no device on lsusb. > > Then I try to boot without the device, it start well the machine, then > plug the device and this is the dmesg: > > [ 162.372030] usb 1-2: new high speed USB device using ehci_hcd and address 2 > [ 177.484038] usb 1-2: device descriptor read/64, error -110 > [ 192.700039] usb 1-2: device descriptor read/64, error -110 > [ 192.920036] usb 1-2: new high speed USB device using ehci_hcd and address 3 > [ 208.028034] usb 1-2: device descriptor read/64, error -110 > [ 223.252028] usb 1-2: device descriptor read/64, error -110 > [ 223.465028] usb 1-2: new high speed USB device using ehci_hcd and address 4 > [ 228.484176] usb 1-2: device descriptor read/8, error -110 > [ 233.604097] usb 1-2: device descriptor read/8, error -110 > [ 233.820029] usb 1-2: new high speed USB device using ehci_hcd and address 5 > [ 238.840170] usb 1-2: device descriptor read/8, error -110 > [ 243.961092] usb 1-2: device descriptor read/8, error -110 > [ 244.064050] hub 1-0:1.0: unable to enumerate USB device on port 2 > [ 244.392034] usb 3-2: new full speed USB device using ohci_hcd and address 2 > [ 259.568033] usb 3-2: device descriptor read/64, error -110 > [ 274.848036] usb 3-2: device descriptor read/64, error -110 > [ 275.128035] usb 3-2: new full speed USB device using ohci_hcd and address 3 > > I contact with Tevii, but there is no support for this device on > Linux, they point me to go to > http://mercurial.intuxication.org/hg/s2-liplianin/ > > I read some users having same problem with this device, here is one > that resolve it uploading I new firmware on each boot: > http://www.gilzad.de/blog/pivot/entry.php?id=7 > > Can you help with this? > > I am not an expert on kernel/driver/firmware, I will apreciate any help. > > Thanks for your help and best regards. > > > -- > Josu Lazkano > Hello again, I try it on the work again, I just install the driver and set the modprobe. I attached and all looks well: $ dmesg [ 5424.064262] usb 1-3: new high speed USB device using ehci_hcd and address 4 [ 5424.196383] usb 1-3: New USB device found, idVendor=9022, idProduct=d660 [ 5424.196387] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 5424.196481] usb 1-3: configuration #1 chosen from 1 choice [ 5424.433400] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware [ 5424.433403] usb 1-3: firmware: requesting dvb-usb-teviis660.fw [ 5424.548027] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw' [ 5424.548030] dw2102: start downloading DW210X firmware [ 5424.564904] usb 1-3: USB disconnect, address 4 [ 5424.668011] dvb-usb: found a 'TeVii S660 USB' in warm state. [ 5424.668045] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 5424.668062] DVB: registering new adapter (TeVii S660 USB) [ 5428.764009] dvb-usb: MAC address: d3:d3:d3:d3:d3:d3 [ 5428.828255] Only Zarlink VP310/MT312/ZL10313 are supported chips. [ 5429.084260] Invalid probe, probably not a DS3000 [ 5429.084322] dvb-usb: no frontend was attached by 'TeVii S660 USB' [ 5429.084325] dvb-usb: TeVii S660 USB successfully initialized and connected. [ 5429.084353] usbcore: registered new interface driver dw2102 [ 5429.084591] dvb-usb: TeVii S660 USB successfully deinitialized and disconnected. [ 5429.324012] usb 1-3: new high speed USB device using ehci_hcd and address 5 [ 5429.456657] usb 1-3: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 2 [ 5429.457030] usb 1-3: New USB device found, idVendor=9022, idProduct=d660 [ 5429.457033] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 5429.457036] usb 1-3: Product: DVBS2BOX [ 5429.457038] usb 1-3: Manufacturer: TBS-Tech [ 5429.457122] usb 1-3: configuration #1 chosen from 1 choice [ 5429.457318] dvb-usb: found a 'TeVii S660 USB' in cold state, will try to load a firmware [ 5429.457322] usb 1-3: firmware: requesting dvb-usb-teviis660.fw [ 5429.459604] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw' [ 5429.459606] dw2102: start downloading DW210X firmware [ 5429.580262] dvb-usb: found a 'TeVii S660 USB' in warm state. [ 5429.580293] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 5429.580419] DVB: registering new adapter (TeVii S660 USB) [ 5433.676256] dvb-usb: MAC address: 00:18:bd:xx:xx:xx [ 5433.696007] Only Zarlink VP310/MT312/ZL10313 are supported chips. [ 5433.972008] DS3000 chip version: 0.192 attached. [ 5433.972010] dw2102: Attached ds3000+ds2020! [ 5433.972011] [ 5433.972158] DVB: registering adapter 6 frontend 0 (Montage Technology DS3000/TS2020)... [ 5433.972409] dvb-usb: TeVii S660 USB successfully initialized and connected. $ lsusb ... Bus 001 Device 005: ID 9022:d660 TeVii Technology Ltd. DVB-S2 S660 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub $ ls -l /dev/dvb/ total 0 drwxr-xr-x 2 root root 120 Aug 11 16:18 adapter6 I have not a dish here to test the signal, but it looks well. I reboot with device connected and it has no errors, maybe it is my hardware issue. I will try again when arrive to home, the hardware is a Nvidia ION board. Regards. -- Josu Lazkano -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
