Re: [PATCH v1 1/5] DT bindings for imx492

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 22-11-28 06:37:58, Laurent Pinchart wrote:
> Hi Petko,
> 
> Thank you for the patch.
> 
> The subject line should start with the proper prefix. Look at the git
> log in the directory to see what is customary. Furthermore,
> s/imx492/Sony IMX492/.
> 
> On Fri, Nov 25, 2022 at 05:31:16PM +0200, Petko Manolov wrote:
> > Here goes the DT bindings file.
> 
> This is also a peculiar commit message :-)

Short and to the point, isn't it? :)

Honestly, i'm not sure what else i should put as subject line, apart from "Sony
IMX492".

> > Signed-off-by: Petko Manolov <petko.manolov@xxxxxxxxxxxx>
> > ---
> >  .../bindings/media/i2c/sony,imx492.yaml       | 101 ++++++++++++++++++
> >  1 file changed, 101 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/media/i2c/sony,imx492.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx492.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx492.yaml
> > new file mode 100644
> > index 000000000000..f4feef17c677
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx492.yaml
> > @@ -0,0 +1,101 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/sony,imx492.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Sony imx492 Sensor
> 
> s/imx492/IMX492/. Same below. When referring to the hardware, it's
> customary to use uppercase.

OK.

> > +
> > +maintainers:
> > +  - Petko Manolov <petko.manolov@xxxxxxxxxxxx>
> > +
> > +description:
> > +
> > +  imx492 is a diagonal 23.1 mm (Type 1.4) CMOS image sensor with color or
> > +  monochrome square pixel array and approximately 47.08 M effective pixels.
> > +  12-bit digital output makes it possible to output the signals with high
> > +  definition for moving pictures. It is programmable through I2C interface. The
> > +  I2C client address can be either 0x10 or 0x1a depending on SLASEL pin. Image
> > +  data is sent through MIPI CSI-2.
> > +
> > +properties:
> > +  compatible:
> > +    const: sony,imx492
> 
> Missing blank line.

OK.

> > +  reg:
> > +    description: I2C address
> 
> You can drop the description.
> 
> > +    maxItems: 1
> > +
> > +  assigned-clocks: true
> > +  assigned-clock-parents: true
> > +  assigned-clock-rates: true
> 
> This shouldn't be needed.

OK.

> > +
> > +  clocks:
> > +    description: Clock frequency 6MHz, 12MHz, 18MHz and 24MHz
> 
> If you know the name of the clock pin, I would include it here.

OK.

> > +    maxItems: 1
> > +
> > +  dovdd-supply:
> > +    description: Interface power supply.
> 
> I would list the voltage. Same below.

OK.

> > +
> > +  avdd-supply:
> > +    description: Analog power supply.
> > +
> > +  dvdd-supply:
> > +    description: Digital power supply.
> > +
> > +  reset-gpios:
> > +    description: Reference to the GPIO connected to the XCLR pin, if any.
> > +    maxItems: 1
> > +
> > +  port:
> > +    additionalProperties: false
> > +    $ref: /schemas/graph.yaml#/$defs/port-base
> > +
> > +    properties:
> > +      endpoint:
> > +        $ref: /schemas/media/video-interfaces.yaml#
> > +        unevaluatedProperties: false
> > +
> > +        properties:
> > +          data-lanes: true
> > +          link-frequencies: true
> > +
> > +        required:
> > +          - data-lanes
> > +          - link-frequencies
> > +
> > +    required:
> > +      - endpoint
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - clocks
> > +  - port
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    i2c0 {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        camera@10 {
> > +            compatible = "sony,imx492";
> > +            reg = <0x10>;
> > +            clocks = <&imx492_clk>;
> > +
> > +            assigned-clocks = <&imx492_clk>;
> > +            assigned-clock-parents = <&imx492_clk_parent>;
> > +            assigned-clock-rates = <24000000>;
> 
> You can drop this from the example, it doesn't showcase the DT bindings for
> the IMX492.

OK.

> > +
> > +            port {
> > +                imx492: endpoint {
> 
> s/imx492/imx492_out/
> 
> > +                    remote-endpoint = <&cam>;
> 
> s/cam/cam_in/

OK to both of the above.

> > +                    data-lanes = <1 2 3 4>;
> > +                    link-frequencies = /bits/ 64 <600000000>;
> > +                };
> > +            };
> > +        };
> > +    };
> > +...
> 
> -- 
> Regards,
> 
> Laurent Pinchart


cheers,
Petko



[Index of Archives]     [Linux Input]     [Video for Linux]     [Gstreamer Embedded]     [Mplayer Users]     [Linux USB Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]

  Powered by Linux