André Weidemann wrote:
> Could please post a link to this patch? I think that a few people on
> this list, including me, are interested in a solution.
The patches should be small enough to post here and are attached. They
were sent to me by Alan Stern when he was looking at the issue. Apply
patch 1 then 2.
(I think they only apply to 2.6.30)
Cheers
David
Index: usb-2.6/drivers/usb/host/ehci-q.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-q.c
+++ usb-2.6/drivers/usb/host/ehci-q.c
@@ -93,22 +93,6 @@ qh_update (struct ehci_hcd *ehci, struct
qh->hw_qtd_next = QTD_NEXT(ehci, qtd->qtd_dma);
qh->hw_alt_next = EHCI_LIST_END(ehci);
- /* Except for control endpoints, we make hardware maintain data
- * toggle (like OHCI) ... here (re)initialize the toggle in the QH,
- * and set the pseudo-toggle in udev. Only usb_clear_halt() will
- * ever clear it.
- */
- if (!(qh->hw_info1 & cpu_to_hc32(ehci, 1 << 14))) {
- unsigned is_out, epnum;
-
- is_out = !(qtd->hw_token & cpu_to_hc32(ehci, 1 << 8));
- epnum = (hc32_to_cpup(ehci, &qh->hw_info1) >> 8) & 0x0f;
- if (unlikely (!usb_gettoggle (qh->dev, epnum, is_out))) {
- qh->hw_token &= ~cpu_to_hc32(ehci, QTD_TOGGLE);
- usb_settoggle (qh->dev, epnum, is_out, 1);
- }
- }
-
/* HC must see latest qtd and qh data before we clear ACTIVE+HALT */
wmb ();
qh->hw_token &= cpu_to_hc32(ehci, QTD_TOGGLE | QTD_STS_PING);
@@ -893,7 +877,6 @@ done:
qh->qh_state = QH_STATE_IDLE;
qh->hw_info1 = cpu_to_hc32(ehci, info1);
qh->hw_info2 = cpu_to_hc32(ehci, info2);
- usb_settoggle (urb->dev, usb_pipeendpoint (urb->pipe), !is_input, 1);
qh_refresh (ehci, qh);
return qh;
}
@@ -928,7 +911,7 @@ static void qh_link_async (struct ehci_h
}
}
- /* clear halt and/or toggle; and maybe recover from silicon quirk */
+ /* clear halt and maybe recover from silicon quirk */
if (qh->qh_state == QH_STATE_IDLE)
qh_refresh (ehci, qh);
Index: usb-2.6/drivers/usb/host/ehci-hcd.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-hcd.c
+++ usb-2.6/drivers/usb/host/ehci-hcd.c
@@ -1026,6 +1026,51 @@ done:
return;
}
+static void
+ehci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep)
+{
+ struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+ struct ehci_qh *qh;
+ int eptype = usb_endpoint_type(&ep->desc);
+
+ if (eptype != USB_ENDPOINT_XFER_BULK && eptype != USB_ENDPOINT_XFER_INT)
+ return;
+
+ rescan:
+ spin_lock_irq(&ehci->lock);
+ qh = ep->hcpriv;
+
+ /* For Bulk and Interrupt endpoints we maintain the toggle state
+ * in the hardware; the toggle bits in udev aren't used at all.
+ * When an endpoint is reset by usb_clear_halt() we must reset
+ * the toggle bit in the QH.
+ */
+ if (qh) {
+ if (!list_empty(&qh->qtd_list)) {
+ WARN_ONCE(1, "clear_halt for a busy endpoint\n");
+ } else if (qh->qh_state == QH_STATE_IDLE) {
+ qh->hw_token &= ~cpu_to_hc32(ehci, QTD_TOGGLE);
+ } else {
+ /* It's not safe to write into the overlay area
+ * while the QH is active. Unlink it first and
+ * wait for the unlink to complete.
+ */
+ if (qh->qh_state == QH_STATE_LINKED) {
+ if (eptype == USB_ENDPOINT_XFER_BULK) {
+ unlink_async(ehci, qh);
+ } else {
+ intr_deschedule(ehci, qh);
+ (void) qh_schedule(ehci, qh);
+ }
+ }
+ spin_unlock_irq(&ehci->lock);
+ schedule_timeout_uninterruptible(1);
+ goto rescan;
+ }
+ }
+ spin_unlock_irq(&ehci->lock);
+}
+
static int ehci_get_frame (struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
Index: usb-2.6/drivers/usb/host/ehci-au1xxx.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-au1xxx.c
+++ usb-2.6/drivers/usb/host/ehci-au1xxx.c
@@ -97,6 +97,7 @@ static const struct hc_driver ehci_au1xx
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
/*
* scheduling support
Index: usb-2.6/drivers/usb/host/ehci-fsl.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-fsl.c
+++ usb-2.6/drivers/usb/host/ehci-fsl.c
@@ -309,6 +309,7 @@ static const struct hc_driver ehci_fsl_h
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
/*
* scheduling support
Index: usb-2.6/drivers/usb/host/ehci-ixp4xx.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-ixp4xx.c
+++ usb-2.6/drivers/usb/host/ehci-ixp4xx.c
@@ -51,6 +51,7 @@ static const struct hc_driver ixp4xx_ehc
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
.get_frame_number = ehci_get_frame,
.hub_status_data = ehci_hub_status_data,
.hub_control = ehci_hub_control,
Index: usb-2.6/drivers/usb/host/ehci-orion.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-orion.c
+++ usb-2.6/drivers/usb/host/ehci-orion.c
@@ -149,6 +149,7 @@ static const struct hc_driver ehci_orion
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
/*
* scheduling support
Index: usb-2.6/drivers/usb/host/ehci-pci.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-pci.c
+++ usb-2.6/drivers/usb/host/ehci-pci.c
@@ -388,6 +388,7 @@ static const struct hc_driver ehci_pci_h
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
/*
* scheduling support
Index: usb-2.6/drivers/usb/host/ehci-ppc-of.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-ppc-of.c
+++ usb-2.6/drivers/usb/host/ehci-ppc-of.c
@@ -61,6 +61,7 @@ static const struct hc_driver ehci_ppc_o
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
/*
* scheduling support
Index: usb-2.6/drivers/usb/host/ehci-ps3.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-ps3.c
+++ usb-2.6/drivers/usb/host/ehci-ps3.c
@@ -65,6 +65,7 @@ static const struct hc_driver ps3_ehci_h
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
.get_frame_number = ehci_get_frame,
.hub_status_data = ehci_hub_status_data,
.hub_control = ehci_hub_control,
Index: usb-2.6/drivers/usb/host/ehci-hcd.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-hcd.c
+++ usb-2.6/drivers/usb/host/ehci-hcd.c
@@ -1032,12 +1032,14 @@ ehci_endpoint_reset(struct usb_hcd *hcd,
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct ehci_qh *qh;
int eptype = usb_endpoint_type(&ep->desc);
+ int epnum = usb_endpoint_num(&ep->desc);
+ int is_out = usb_endpoint_dir_out(&ep->desc);
+ unsigned long flags;
if (eptype != USB_ENDPOINT_XFER_BULK && eptype != USB_ENDPOINT_XFER_INT)
return;
- rescan:
- spin_lock_irq(&ehci->lock);
+ spin_lock_irqsave(&ehci->lock, flags);
qh = ep->hcpriv;
/* For Bulk and Interrupt endpoints we maintain the toggle state
@@ -1046,29 +1048,24 @@ ehci_endpoint_reset(struct usb_hcd *hcd,
* the toggle bit in the QH.
*/
if (qh) {
+ usb_settoggle(qh->dev, epnum, is_out, 0);
if (!list_empty(&qh->qtd_list)) {
WARN_ONCE(1, "clear_halt for a busy endpoint\n");
- } else if (qh->qh_state == QH_STATE_IDLE) {
- qh->hw_token &= ~cpu_to_hc32(ehci, QTD_TOGGLE);
- } else {
- /* It's not safe to write into the overlay area
- * while the QH is active. Unlink it first and
- * wait for the unlink to complete.
+ } else if (qh->qh_state == QH_STATE_LINKED) {
+
+ /* The toggle value in the QH can't be updated
+ * while the QH is active. Unlink it now;
+ * re-linking will call qh_refresh().
*/
- if (qh->qh_state == QH_STATE_LINKED) {
- if (eptype == USB_ENDPOINT_XFER_BULK) {
- unlink_async(ehci, qh);
- } else {
- intr_deschedule(ehci, qh);
- (void) qh_schedule(ehci, qh);
- }
+ if (eptype == USB_ENDPOINT_XFER_BULK) {
+ unlink_async(ehci, qh);
+ } else {
+ intr_deschedule(ehci, qh);
+ (void) qh_schedule(ehci, qh);
}
- spin_unlock_irq(&ehci->lock);
- schedule_timeout_uninterruptible(1);
- goto rescan;
}
}
- spin_unlock_irq(&ehci->lock);
+ spin_unlock_irqrestore(&ehci->lock, flags);
}
static int ehci_get_frame (struct usb_hcd *hcd)
Index: usb-2.6/drivers/usb/host/ehci-q.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-q.c
+++ usb-2.6/drivers/usb/host/ehci-q.c
@@ -93,6 +93,22 @@ qh_update (struct ehci_hcd *ehci, struct
qh->hw_qtd_next = QTD_NEXT(ehci, qtd->qtd_dma);
qh->hw_alt_next = EHCI_LIST_END(ehci);
+ /* Except for control endpoints, we make hardware maintain data
+ * toggle (like OHCI) ... here (re)initialize the toggle in the QH,
+ * and set the pseudo-toggle in udev. Only usb_clear_halt() will
+ * ever clear it.
+ */
+ if (!(qh->hw_info1 & cpu_to_hc32(ehci, 1 << 14))) {
+ unsigned is_out, epnum;
+
+ is_out = !(qtd->hw_token & cpu_to_hc32(ehci, 1 << 8));
+ epnum = (hc32_to_cpup(ehci, &qh->hw_info1) >> 8) & 0x0f;
+ if (unlikely (!usb_gettoggle (qh->dev, epnum, is_out))) {
+ qh->hw_token &= ~cpu_to_hc32(ehci, QTD_TOGGLE);
+ usb_settoggle (qh->dev, epnum, is_out, 1);
+ }
+ }
+
/* HC must see latest qtd and qh data before we clear ACTIVE+HALT */
wmb ();
qh->hw_token &= cpu_to_hc32(ehci, QTD_TOGGLE | QTD_STS_PING);
@@ -877,6 +893,7 @@ done:
qh->qh_state = QH_STATE_IDLE;
qh->hw_info1 = cpu_to_hc32(ehci, info1);
qh->hw_info2 = cpu_to_hc32(ehci, info2);
+ usb_settoggle (urb->dev, usb_pipeendpoint (urb->pipe), !is_input, 1);
qh_refresh (ehci, qh);
return qh;
}
@@ -911,7 +928,7 @@ static void qh_link_async (struct ehci_h
}
}
- /* clear halt and maybe recover from silicon quirk */
+ /* clear halt and/or toggle; and maybe recover from silicon quirk */
if (qh->qh_state == QH_STATE_IDLE)
qh_refresh (ehci, qh);
