On Fri, 21 Feb 2025 17:09:18 +0800
Eason Yang <j2anfernee@xxxxxxxxx> wrote:
> Add Nuvoton NCT7201/NCT7202 system voltage monitor 12-bit ADC driver
>
> NCT7201/NCT7202 supports up to 12 analog voltage monitor inputs and up to
> 4 SMBus addresses by ADDR pin. Meanwhile, ALERT# hardware event pins for
> independent alarm signals, and the all threshold values could be set for
> system protection without any timing delay. It also supports reset input
> RSTIN# to recover system from a fault condition.
>
> Currently, only single-edge mode conversion and threshold events support.
>
> Signed-off-by: Eason Yang <j2anfernee@xxxxxxxxx>
Hi Eason
A few comments from me. May well overlap in some places with other feedback.
Jonathan
> diff --git a/drivers/iio/adc/nct7201.c b/drivers/iio/adc/nct7201.c
> new file mode 100644
> index 000000000000..c5d1540bcc00
> --- /dev/null
> +++ b/drivers/iio/adc/nct7201.c
> @@ -0,0 +1,487 @@
> +
> +#define NCT7201_VOLTAGE_CHANNEL(chan, addr) \
> + { \
> + .type = IIO_VOLTAGE, \
> + .indexed = 1, \
> + .channel = chan, \
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
> + .address = addr, \
> + .event_spec = nct7201_events, \
> + .num_event_specs = ARRAY_SIZE(nct7201_events), \
> + }
> +
> +static const struct iio_chan_spec nct7201_channels[] = {
> + NCT7201_VOLTAGE_CHANNEL(1, 0),
> + NCT7201_VOLTAGE_CHANNEL(2, 1),
> + NCT7201_VOLTAGE_CHANNEL(3, 2),
> + NCT7201_VOLTAGE_CHANNEL(4, 3),
> + NCT7201_VOLTAGE_CHANNEL(5, 4),
> + NCT7201_VOLTAGE_CHANNEL(6, 5),
> + NCT7201_VOLTAGE_CHANNEL(7, 6),
> + NCT7201_VOLTAGE_CHANNEL(8, 7),
> +};
> +
> +static const struct iio_chan_spec nct7202_channels[] = {
> + NCT7201_VOLTAGE_CHANNEL(1, 0),
> + NCT7201_VOLTAGE_CHANNEL(2, 1),
> + NCT7201_VOLTAGE_CHANNEL(3, 2),
> + NCT7201_VOLTAGE_CHANNEL(4, 3),
> + NCT7201_VOLTAGE_CHANNEL(5, 4),
> + NCT7201_VOLTAGE_CHANNEL(6, 5),
> + NCT7201_VOLTAGE_CHANNEL(7, 6),
> + NCT7201_VOLTAGE_CHANNEL(8, 7),
> + NCT7201_VOLTAGE_CHANNEL(9, 8),
> + NCT7201_VOLTAGE_CHANNEL(10, 9),
> + NCT7201_VOLTAGE_CHANNEL(11, 10),
> + NCT7201_VOLTAGE_CHANNEL(12, 11),
We normally number channels from 0 which would simplify this but I don't really
mind if you want to keep the offset of 1. Maybe just have one macro
parameter though and do the +1 in the macro.
> +};
> +static int nct7201_read_event_value(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + enum iio_event_info info,
> + int *val, int *val2)
> +{
> + struct nct7201_chip_info *chip = iio_priv(indio_dev);
> + u16 volt;
> + unsigned int value;
> + int err;
> +
> + if (chan->type != IIO_VOLTAGE)
> + return -EOPNOTSUPP;
> +
> + if (info != IIO_EV_INFO_VALUE)
> + return -EINVAL;
> +
> + if (dir == IIO_EV_DIR_FALLING) {
> + err = regmap_read(chip->regmap16, NCT7201_REG_VIN_LOW_LIMIT(chan->address),
> + &value);
> + if (err < 0)
> + return err;
> + volt = value;
> + } else {
> + err = regmap_read(chip->regmap16, NCT7201_REG_VIN_HIGH_LIMIT(chan->address),
> + &value);
> + if (err < 0)
> + return err;
> + volt = value;
No real point in assigning to volt here,
> + }
> +
> + *val = FIELD_GET(NCT7201_REG_VIN_MASK, volt);
> +
> + return IIO_VAL_INT;
> +}
> +
> +static int nct7201_write_event_value(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + enum iio_event_info info,
> + int val, int val2)
> +{
> + struct nct7201_chip_info *chip = iio_priv(indio_dev);
> +
> + if (chan->type != IIO_VOLTAGE)
> + return -EOPNOTSUPP;
> +
> + if (info != IIO_EV_INFO_VALUE)
> + return -EOPNOTSUPP;
> +
> + if (dir == IIO_EV_DIR_FALLING)
> + regmap_write(chip->regmap16, NCT7201_REG_VIN_LOW_LIMIT(chan->address),
> + FIELD_PREP(NCT7201_REG_VIN_MASK, val));
> + else
> + regmap_write(chip->regmap16, NCT7201_REG_VIN_HIGH_LIMIT(chan->address),
> + FIELD_PREP(NCT7201_REG_VIN_MASK, val));
Check for error returns.
> +
> + return 0;
> +}
> +
> +static int nct7201_read_event_config(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir)
> +{
> + struct nct7201_chip_info *chip = iio_priv(indio_dev);
> +
> + if (chan->type != IIO_VOLTAGE)
> + return -EOPNOTSUPP;
> +
> + return !!(chip->vin_mask & BIT(chan->address));
> +}
> +
> +static int nct7201_write_event_config(struct iio_dev *indio_dev,
> + const struct iio_chan_spec *chan,
> + enum iio_event_type type,
> + enum iio_event_direction dir,
> + bool state)
> +{
> + struct nct7201_chip_info *chip = iio_priv(indio_dev);
> + unsigned int mask;
> +
> + if (chan->type != IIO_VOLTAGE)
> + return -EOPNOTSUPP;
> +
> + mask = BIT(chan->address);
> +
> + if (!state && (chip->vin_mask & mask))
> + chip->vin_mask &= ~mask;
> + else if (state && !(chip->vin_mask & mask))
> + chip->vin_mask |= mask;
> +
> + if (chip->num_vin_channels <= 8)
> + regmap_write(chip->regmap, NCT7201_REG_CHANNEL_ENABLE_1, chip->vin_mask);
> + else
> + regmap_bulk_write(chip->regmap, NCT7201_REG_CHANNEL_ENABLE_1,
> + &chip->vin_mask, sizeof(chip->vin_mask));
Check errors on these writes.
> +
> + return 0;
> +}
> +static int nct7201_init_chip(struct nct7201_chip_info *chip)
> +{
> + u8 data[2];
> + unsigned int value;
> + int err;
> +
> + regmap_write(chip->regmap, NCT7201_REG_CONFIGURATION,
> + NCT7201_BIT_CONFIGURATION_RESET);
Check for errors on all accesses to the device. It can get
fiddly in paths where you are already handling an error but
that's not the case here.
> +
> + /*
> + * After about 25 msecs, the device should be ready and then
> + * the Power Up bit will be set to 1. If not, wait for it.
Wrap to 80 chars.
> + */
> + mdelay(25);
> + err = regmap_read(chip->regmap, NCT7201_REG_BUSY_STATUS, &value);
> + if (err < 0)
> + return err;
> + if (!(value & NCT7201_BIT_PWR_UP))
> + return dev_err_probe(&chip->client->dev, -EIO,
> + "Failed to power up after reset\n");
> +
> + /* Enable Channel */
> + if (chip->num_vin_channels <= 8) {
> + data[0] = NCT7201_REG_CHANNEL_ENABLE_1_MASK;
> + err = regmap_write(chip->regmap, NCT7201_REG_CHANNEL_ENABLE_1, data[0]);
> + if (err < 0)
> + return dev_err_probe(&chip->client->dev, -EIO,
> + "Failed to write NCT7201_REG_CHANNEL_ENABLE_1\n");
> + } else {
> + data[0] = NCT7201_REG_CHANNEL_ENABLE_1_MASK;
> + data[1] = NCT7201_REG_CHANNEL_ENABLE_2_MASK;
> + err = regmap_bulk_write(chip->regmap, NCT7201_REG_CHANNEL_ENABLE_1,
> + data, ARRAY_SIZE(data));
> + if (err < 0)
> + return dev_err_probe(&chip->client->dev, -EIO,
> + "Failed to write NCT7201_REG_CHANNEL_ENABLE_1 and NCT7201_REG_CHANNEL_ENABLE_2\n");
> + }
> +
> + value = get_unaligned_le16(data);
> + chip->vin_mask = value;
Local variable doesn't seem to add any benefits so just assign vin_mask directly.
> +
> + /* Start monitoring if needed */
> + err = regmap_read(chip->regmap, NCT7201_REG_CONFIGURATION, &value);
> + if (err < 0)
> + return dev_err_probe(&chip->client->dev, -EIO,
> + "Failed to read NCT7201_REG_CONFIGURATION\n");
> +
> + regmap_set_bits(chip->regmap, NCT7201_REG_CONFIGURATION, NCT7201_BIT_CONFIGURATION_START);
> +
> + return 0;
> +}
> +
> +static int nct7201_probe(struct i2c_client *client)
> +{
> + const struct nct7201_adc_model_data *model_data;
> + struct nct7201_chip_info *chip;
> + struct iio_dev *indio_dev;
> + int ret;
> +
> + model_data = i2c_get_match_data(client);
> + if (!model_data)
> + return -EINVAL;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip));
> + if (!indio_dev)
> + return -ENOMEM;
> + chip = iio_priv(indio_dev);
> +
> + chip->regmap = devm_regmap_init_i2c(client, &nct7201_regmap8_config);
> + if (IS_ERR(chip->regmap))
> + return dev_err_probe(&client->dev, PTR_ERR(chip->regmap),
> + "Failed to init regmap\n");
Where it doesn't lead to really long lines, align all parameters to just
after the opening bracket.
> +
> + chip->regmap16 = devm_regmap_init_i2c(client, &nct7201_regmap16_config);
> + if (IS_ERR(chip->regmap16))
> + return dev_err_probe(&client->dev, PTR_ERR(chip->regmap16),
> + "Failed to init regmap16\n");
> +
> + chip->num_vin_channels = model_data->num_vin_channels;
> +
> + ret = devm_mutex_init(&client->dev, &chip->access_lock);
> + if (ret)
> + return ret;
> +
> + chip->client = client;
> +
> + ret = nct7201_init_chip(chip);
> + if (ret < 0)
> + return ret;
> +
> + indio_dev->name = model_data->model_name;
> + indio_dev->channels = model_data->channels;
> + indio_dev->num_channels = model_data->num_channels;
> + if (client->irq)
> + indio_dev->info = &nct7201_info;
> + else
> + indio_dev->info = &nct7201_info_no_irq;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> +
> + return devm_iio_device_register(&client->dev, indio_dev);
> +}
