Modify the startup procedure to reflect the procedure of the Bosch BME68x Sensor API. The initial readings and configuration of the sensor need to happen in the following order: 1) Read calibration data [1,2] 2) Chip general configuration [3] 3) Gas configuration [4] After the chip configuration it is necessary to ensure that the sensor is in sleeping mode, in order to apply the gas configuration settings [5]. Also, after the soft reset, it is advised to wait for 5ms [6]. Link: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L162 # [1] Link: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L44 # [2] Link: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L53 # [3] Link: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L60 # [4] Link: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L640 # [5] Link: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L294 # [6] Signed-off-by: Vasileios Amoiridis <vassilisamir@xxxxxxxxx> --- drivers/iio/chemical/bme680.h | 2 ++ drivers/iio/chemical/bme680_core.c | 21 ++++++++++++++------- 2 files changed, 16 insertions(+), 7 deletions(-) diff --git a/drivers/iio/chemical/bme680.h b/drivers/iio/chemical/bme680.h index 7d0ff294725a..b2c547ac8d34 100644 --- a/drivers/iio/chemical/bme680.h +++ b/drivers/iio/chemical/bme680.h @@ -63,6 +63,8 @@ #define BME680_MEAS_TRIM_MASK GENMASK(24, 4) +#define BME680_STARTUP_TIME_US 5000 + /* Calibration Parameters */ #define BME680_T2_LSB_REG 0x8A #define BME680_H2_MSB_REG 0xE1 diff --git a/drivers/iio/chemical/bme680_core.c b/drivers/iio/chemical/bme680_core.c index a54460fddc91..0390c298fdd8 100644 --- a/drivers/iio/chemical/bme680_core.c +++ b/drivers/iio/chemical/bme680_core.c @@ -531,6 +531,11 @@ static int bme680_gas_config(struct bme680_data *data) int ret; u8 heatr_res, heatr_dur; + /* Go to sleep */ + ret = bme680_set_mode(data, false); + if (ret < 0) + return ret; + heatr_res = bme680_calc_heater_res(data, data->heater_temp); /* set target heater temperature */ @@ -866,6 +871,8 @@ int bme680_core_probe(struct device *dev, struct regmap *regmap, return ret; } + usleep_range(BME680_STARTUP_TIME_US, BME680_STARTUP_TIME_US + 1000); + ret = regmap_read(regmap, BME680_REG_CHIP_ID, &data->check); if (ret < 0) { dev_err(dev, "Error reading chip ID\n"); @@ -878,22 +885,22 @@ int bme680_core_probe(struct device *dev, struct regmap *regmap, return -ENODEV; } - ret = bme680_chip_config(data); + ret = bme680_read_calib(data, &data->bme680); if (ret < 0) { - dev_err(dev, "failed to set chip_config data\n"); + dev_err(dev, + "failed to read calibration coefficients at probe\n"); return ret; } - ret = bme680_gas_config(data); + ret = bme680_chip_config(data); if (ret < 0) { - dev_err(dev, "failed to set gas config data\n"); + dev_err(dev, "failed to set chip_config data\n"); return ret; } - ret = bme680_read_calib(data, &data->bme680); + ret = bme680_gas_config(data); if (ret < 0) { - dev_err(dev, - "failed to read calibration coefficients at probe\n"); + dev_err(dev, "failed to set gas config data\n"); return ret; } -- 2.25.1
