Add threshold events support for temperature and relative humidity. To enable them the higher and lower threshold registers must be programmed and the higher threshold must be greater then or equal to the lower threshold. Otherwise the event is disabled. Invalid hysteresis values are ignored by the device. There is no further configuration possible. Tested by setting thresholds/hysteresis and turning the heater on/off. Used iio_event_monitor in tools/iio to catch events while constantly displaying temperature and humidity values. Signed-off-by: Dimitri Fedrau <dima.fedrau@xxxxxxxxx> --- drivers/iio/humidity/hdc3020.c | 245 +++++++++++++++++++++++++++++++++ 1 file changed, 245 insertions(+) diff --git a/drivers/iio/humidity/hdc3020.c b/drivers/iio/humidity/hdc3020.c index 4ae4dd3187db..921d6061ef0d 100644 --- a/drivers/iio/humidity/hdc3020.c +++ b/drivers/iio/humidity/hdc3020.c @@ -8,35 +8,62 @@ * Datasheet: https://www.ti.com/lit/ds/symlink/hdc3020.pdf */ +#include <linux/bitfield.h> #include <linux/bitops.h> #include <linux/cleanup.h> #include <linux/crc8.h> #include <linux/delay.h> #include <linux/i2c.h> #include <linux/init.h> +#include <linux/interrupt.h> #include <linux/module.h> #include <linux/mutex.h> +#include <linux/units.h> #include <asm/unaligned.h> +#include <linux/iio/events.h> #include <linux/iio/iio.h> #define HDC3020_S_AUTO_10HZ_MOD0 0x2737 +#define HDC3020_S_STATUS 0x3041 #define HDC3020_HEATER_DISABLE 0x3066 #define HDC3020_HEATER_ENABLE 0x306D #define HDC3020_HEATER_CONFIG 0x306E #define HDC3020_EXIT_AUTO 0x3093 +#define HDC3020_S_T_RH_THRESH_LOW 0x6100 +#define HDC3020_S_T_RH_THRESH_LOW_CLR 0x610B +#define HDC3020_S_T_RH_THRESH_HIGH_CLR 0x6116 +#define HDC3020_S_T_RH_THRESH_HIGH 0x611D #define HDC3020_R_T_RH_AUTO 0xE000 #define HDC3020_R_T_LOW_AUTO 0xE002 #define HDC3020_R_T_HIGH_AUTO 0xE003 #define HDC3020_R_RH_LOW_AUTO 0xE004 #define HDC3020_R_RH_HIGH_AUTO 0xE005 +#define HDC3020_R_T_RH_THRESH_LOW 0xE102 +#define HDC3020_R_T_RH_THRESH_LOW_CLR 0xE109 +#define HDC3020_R_T_RH_THRESH_HIGH_CLR 0xE114 +#define HDC3020_R_T_RH_THRESH_HIGH 0xE11F +#define HDC3020_R_STATUS 0xF32D + +#define HDC3020_THRESH_TEMP_MASK GENMASK(8, 0) +#define HDC3020_THRESH_TEMP_TRUNC_SHIFT 7 +#define HDC3020_THRESH_HUM_MASK GENMASK(15, 9) +#define HDC3020_THRESH_HUM_TRUNC_SHIFT 9 + +#define HDC3020_STATUS_T_LOW_ALERT BIT(6) +#define HDC3020_STATUS_T_HIGH_ALERT BIT(7) +#define HDC3020_STATUS_RH_LOW_ALERT BIT(8) +#define HDC3020_STATUS_RH_HIGH_ALERT BIT(9) #define HDC3020_READ_RETRY_TIMES 10 #define HDC3020_BUSY_DELAY_MS 10 #define HDC3020_CRC8_POLYNOMIAL 0x31 +#define HDC3020_MIN_TEMP -40 +#define HDC3020_MAX_TEMP 125 + struct hdc3020_data { struct i2c_client *client; /* @@ -50,18 +77,37 @@ struct hdc3020_data { static const int hdc3020_heater_vals[] = {0, 1, 0x3FFF}; +static const struct iio_event_spec hdc3020_t_rh_event[] = { + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_RISING, + .mask_separate = BIT(IIO_EV_INFO_VALUE) | + BIT(IIO_EV_INFO_HYSTERESIS), + }, + { + .type = IIO_EV_TYPE_THRESH, + .dir = IIO_EV_DIR_FALLING, + .mask_separate = BIT(IIO_EV_INFO_VALUE) | + BIT(IIO_EV_INFO_HYSTERESIS), + }, +}; + static const struct iio_chan_spec hdc3020_channels[] = { { .type = IIO_TEMP, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_PEAK) | BIT(IIO_CHAN_INFO_TROUGH) | BIT(IIO_CHAN_INFO_OFFSET), + .event_spec = hdc3020_t_rh_event, + .num_event_specs = ARRAY_SIZE(hdc3020_t_rh_event), }, { .type = IIO_HUMIDITYRELATIVE, .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_PEAK) | BIT(IIO_CHAN_INFO_TROUGH), + .event_spec = hdc3020_t_rh_event, + .num_event_specs = ARRAY_SIZE(hdc3020_t_rh_event), }, { /* @@ -315,10 +361,192 @@ static int hdc3020_write_raw(struct iio_dev *indio_dev, return -EINVAL; } +static int hdc3020_write_thresh(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int val, int val2) +{ + struct hdc3020_data *data = iio_priv(indio_dev); + u8 buf[5]; + u64 tmp; + u16 reg; + int ret; + + /* Supported temperature range is from –40 to 125 degree celsius */ + if (val < HDC3020_MIN_TEMP || val > HDC3020_MAX_TEMP) + return -EINVAL; + + /* Select threshold register */ + if (info == IIO_EV_INFO_VALUE) { + if (dir == IIO_EV_DIR_RISING) + reg = HDC3020_S_T_RH_THRESH_HIGH; + else + reg = HDC3020_S_T_RH_THRESH_LOW; + } else { + if (dir == IIO_EV_DIR_RISING) + reg = HDC3020_S_T_RH_THRESH_HIGH_CLR; + else + reg = HDC3020_S_T_RH_THRESH_LOW_CLR; + } + + guard(mutex)(&data->lock); + ret = hdc3020_read_be16(data, reg); + if (ret < 0) + return ret; + + switch (chan->type) { + case IIO_TEMP: + /* + * Calculate temperature threshold, shift it down to get the + * truncated threshold representation in the 9LSBs while keeping + * the current humidity threshold in the 7 MSBs. + */ + tmp = ((u64)(((val + 45) * MICRO) + val2)) * 65535ULL; + tmp = div_u64(tmp, MICRO * 175); + val = tmp >> HDC3020_THRESH_TEMP_TRUNC_SHIFT; + val = FIELD_PREP(HDC3020_THRESH_TEMP_MASK, val); + val |= (FIELD_GET(HDC3020_THRESH_HUM_MASK, ret) << + HDC3020_THRESH_HUM_TRUNC_SHIFT); + break; + case IIO_HUMIDITYRELATIVE: + /* + * Calculate humidity threshold, shift it down and up to get the + * truncated threshold representation in the 7MSBs while keeping + * the current temperature threshold in the 9 LSBs. + */ + tmp = ((u64)((val * MICRO) + val2)) * 65535ULL; + tmp = div_u64(tmp, MICRO * 100); + val = tmp >> HDC3020_THRESH_HUM_TRUNC_SHIFT; + val = FIELD_PREP(HDC3020_THRESH_HUM_MASK, val); + val |= FIELD_GET(HDC3020_THRESH_TEMP_MASK, ret); + break; + default: + return -EOPNOTSUPP; + } + + put_unaligned_be16(reg, buf); + put_unaligned_be16(val, buf + 2); + buf[4] = crc8(hdc3020_crc8_table, buf + 2, 2, CRC8_INIT_VALUE); + return hdc3020_write_bytes(data, buf, 5); +} + +static int hdc3020_read_thresh(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + enum iio_event_type type, + enum iio_event_direction dir, + enum iio_event_info info, + int *val, int *val2) +{ + struct hdc3020_data *data = iio_priv(indio_dev); + u16 reg; + int ret; + + /* Select threshold register */ + if (info == IIO_EV_INFO_VALUE) { + if (dir == IIO_EV_DIR_RISING) + reg = HDC3020_R_T_RH_THRESH_HIGH; + else + reg = HDC3020_R_T_RH_THRESH_LOW; + } else { + if (dir == IIO_EV_DIR_RISING) + reg = HDC3020_R_T_RH_THRESH_HIGH_CLR; + else + reg = HDC3020_R_T_RH_THRESH_LOW_CLR; + } + + guard(mutex)(&data->lock); + ret = hdc3020_read_be16(data, reg); + if (ret < 0) + return ret; + + switch (chan->type) { + case IIO_TEMP: + /* + * Get the temperature threshold from 9 LSBs, shift them to get + * the truncated temperature threshold representation and + * calculate the threshold according to the formula in the + * datasheet. + */ + *val = FIELD_GET(HDC3020_THRESH_TEMP_MASK, ret); + *val = *val << HDC3020_THRESH_TEMP_TRUNC_SHIFT; + *val = -2949075 + (175 * (*val)); + *val2 = 65535; + return IIO_VAL_FRACTIONAL; + case IIO_HUMIDITYRELATIVE: + /* + * Get the humidity threshold from 7 MSBs, shift them to get the + * truncated humidity threshold representation and calculate the + * threshold according to the formula in the datasheet. + */ + *val = FIELD_GET(HDC3020_THRESH_HUM_MASK, ret); + *val = (*val << HDC3020_THRESH_HUM_TRUNC_SHIFT) * 100; + *val2 = 65535; + return IIO_VAL_FRACTIONAL; + default: + return -EOPNOTSUPP; + } +} + +static irqreturn_t hdc3020_interrupt_handler(int irq, void *private) +{ + struct iio_dev *indio_dev = private; + struct hdc3020_data *data; + s64 time; + int ret; + + data = iio_priv(indio_dev); + ret = hdc3020_read_be16(data, HDC3020_R_STATUS); + if (ret < 0) + return IRQ_HANDLED; + + if (!(ret & (HDC3020_STATUS_T_HIGH_ALERT | HDC3020_STATUS_T_LOW_ALERT | + HDC3020_STATUS_RH_HIGH_ALERT | HDC3020_STATUS_RH_LOW_ALERT))) + return IRQ_NONE; + + time = iio_get_time_ns(indio_dev); + if (ret & HDC3020_STATUS_T_HIGH_ALERT) + iio_push_event(indio_dev, + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, + IIO_NO_MOD, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_RISING), + time); + + if (ret & HDC3020_STATUS_T_LOW_ALERT) + iio_push_event(indio_dev, + IIO_MOD_EVENT_CODE(IIO_TEMP, 0, + IIO_NO_MOD, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_FALLING), + time); + + if (ret & HDC3020_STATUS_RH_HIGH_ALERT) + iio_push_event(indio_dev, + IIO_MOD_EVENT_CODE(IIO_HUMIDITYRELATIVE, 0, + IIO_NO_MOD, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_RISING), + time); + + if (ret & HDC3020_STATUS_RH_LOW_ALERT) + iio_push_event(indio_dev, + IIO_MOD_EVENT_CODE(IIO_HUMIDITYRELATIVE, 0, + IIO_NO_MOD, + IIO_EV_TYPE_THRESH, + IIO_EV_DIR_FALLING), + time); + + return IRQ_HANDLED; +} + static const struct iio_info hdc3020_info = { .read_raw = hdc3020_read_raw, .write_raw = hdc3020_write_raw, .read_avail = hdc3020_read_available, + .read_event_value = hdc3020_read_thresh, + .write_event_value = hdc3020_write_thresh, }; static void hdc3020_stop(void *data) @@ -350,6 +578,23 @@ static int hdc3020_probe(struct i2c_client *client) indio_dev->info = &hdc3020_info; indio_dev->channels = hdc3020_channels; indio_dev->num_channels = ARRAY_SIZE(hdc3020_channels); + if (client->irq) { + ret = devm_request_threaded_irq(&client->dev, client->irq, + NULL, hdc3020_interrupt_handler, + IRQF_ONESHOT, "hdc3020", + indio_dev); + if (ret) + return dev_err_probe(&client->dev, ret, + "Failed to request IRQ\n"); + + /* + * The alert output is activated by default upon power up, + * hardware reset, and soft reset. Clear the status register. + */ + ret = hdc3020_exec_cmd(data, HDC3020_S_STATUS); + if (ret) + return ret; + } ret = hdc3020_exec_cmd(data, HDC3020_S_AUTO_10HZ_MOD0); if (ret) -- 2.39.2
