On Sun, 17 Oct 2021 11:36:08 +0100 Jonathan Cameron <jic23@xxxxxxxxxx> wrote: > The following changes since commit 6880fa6c56601bb8ed59df6c30fd390cc5f6dd8f: > > Linux 5.15-rc1 (2021-09-12 16:28:37 -0700) > > are available in the Git repository at: > > https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git tags/iio-for-5.16a-split-v2 > > for you to fetch changes up to ec20da0c69b2c6d0f2864097e791fac1b04d3e4f: > > iio: imx8qxp-adc: mark PM functions as __maybe_unused (2021-10-17 11:06:07 +0100) This one is bad because I forgot to fix up fixes tags after the rebase. > > ---------------------------------------------------------------- > First set of IIO new device and feature support for the 5.16 cycle > > Counter subsystem changes now sent separately. > > This has been a busy cycle, so lots here and a few more stragglers to > come next week. > > Big new feature in this cycle is probably output buffer support. > This has been in the works for a very long time so it's great to see > Mihail pick up the challenge and build upon his predecessors work to finally > bring this feature to mainline. > > New device support > ------------------ > > * adi,adxl313 > - New driver and dt bindings for this low power accelerometer. > * adi,adxl355 > - New driver and dt bindings for this accelerometer. > - Later series adds buffer support. > * asahi-kasei,ak8975 > - Minor additions to driver to support ak09916 > * aspeed,aspeed-adc > - Substantial rework plus feature additions to add support for the > ast2600 including a new dt bindings doc. > * atmel,at91_sama5d2 > - Rework and support introduced for the sama7g5 parts. > * maxim,max31865 > - New driver and bindings for this RTD temperature sensor chip. > * nxp,imx8qxp > - New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc. > * senseair,sunrise > - New driver and bindings for this family of carbon dioxide gas sensors. > * sensiron,scd4x > - New driver and bindings for this carbon dioxide gas sensor. > > New features > ------------ > > * Output buffer support. Works in a similar fashion to input buffers, but > in this case userspace pushes data into the kfifo which is then drained > to the device when a trigger occurs. Support added to the ad5766 DAC > driver. > * Core, devm_iio_map_array_register() to avoid need for > devm_add_action_or_reset() based cleanup in fully managed allocation > drivers. > * Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a > few drivers where it really hard to ensure the correct data alignment in > an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce > buffer so should be avoided whenever possible. Used in the ti,adc108s102, > invense,mpu3050 and adi,adis16400. This closes the last known set > of drivers with alignment issues at this interface. > * maxim,max1027 > - Substantial rework to this driver main target of which was supporting > use of other triggers than it's own EOC interrupt. > - Transfer optimization. > * nxp,fxls8962af > - Threshold even support including using it as a wakeup source. > > Cleanups, minor fixes etc > ------------------------- > > Chances of a common type to multiple drivers: > > * devm_ conversion and drop of .remove() callbacks in: > - adi,ad5064 > - adi,ad7291 > - adi,ad7303 > - adi,ad7746 > - adi,ad9832 > - adi,adis16080 > - dialog,da9150-gpadc > - intel,mrfld_adc > - marvell,berlin2 > - maxim,max1363 > - maxim,max44000 > - nuvoton,nau7802 > - st_sensors (includes a lot of rework!) > - ti,ads8344 > - ti,lp8788 > > * devm_platform_ioremap_resource() used to reduce boilerplate > - cirrus,ep93xx > - rockchip,saradc > - stm,stm32-dac > > * Use dev_err_probe() in more places to both not print on deferred probe and > ensure a reason for the deferral is available for debug purposes. > - adi,ad8801 > - capella,cm36651 > - linear,ltc1660 > - maxim,ds4424 > - maxim,max5821 > - microchip,mcp4922 > - nxp,lpc18xx > - onnn,noa1305 > - st,lsm9ds0 > - st,st_sensors > - st,stm32-dac > - ti,afe4403 > - ti,afe4404 > - ti,dac7311 > > * Drop error returns in SPI and I2C remove() functions as they are ignored and > long term plan is to change these all over to returning void. In some cases > these patches just make it 'obvious' they always return 0 where it was the > case before but not easy to tell. > - adi,ad5380 > - adi,ad5446 > - adi,ad5686 > - adi,ad5592r > - bosch,bma400 > - bosch,bmc150 > - fsl,mma7455 > - honeywell,hmc5843 > - kionix,kxsd9 > - maxim,max5487 > - meas,ms5611 > - ti,afe4403 > > Driver specific changes > > * adi,ad5770r > - Bring driver inline with documented bindings. > * adi,ad7746 > - Trivial style fix > * adi,ad7949 > - Express some magic values as the underlying parts via new #defines. > - Make it work with SPI controllers that don't support 14 or 16 bit messages > - Support selection of voltage reference from dt including expanding the > dt-bindings to cover this new functionality. > * adi,ad799x > - Implement selection of external reference voltage on AD7991, AD7995 and > AD7999. > - Add missing dt-bindings doc for devices supported by this driver. > * adi,adislib > - Move interrupt startup to better location in startup flow. > - Handle devices that cannot mask/unmask the drdy pin and must instead mask > at the interrupt controller. Applies to the adis16460 and adis16475 from > which we then drop equivalent code. > * adi,ltc2983 > - Add support for optional reset pin. > - Fail to probe if no channels specified in dt binding. > * asahi-kasei,ak8975 > - dt-binding additions of missing vid-supply regulator. > * aspeed,aspeed-adc > - Typo fix. > * fsl,mma7660 > - Mark acpi_device_id table __maybe_unused to avoid build warning. > * fsl,imx25-gcq > - Avoid initializing regulators that aren't used. > * invensense,mpu3050 > - Drop a dead protection against a clash with the old input driver. > * invensense,mpu6050 > - Rework code to not use strcpy() and hence avoid possibility of wrong sized > buffers. Note this wasn't a bug, but the new code is a lot more readable. > - Mark acpi_device_id table __maybe_unused to avoid build warning. > * kionix,kxcjk1013 > - dt-binding addition to note it supports interrupts. > * marvell,berlin2-adc > - Enable COMPILE_TEST building. > * maxim,max1027 > - Avoid returning success in an error path. > * nxp,imx8qxp > - Fix warning when runtime pm not enabled via __maybe_unused. > * ricoh,rn5t618 > - Use the new devm_iio_map_array_register() instead of open coding the same. > * samsung,exynos_adc > - Improve kconfig help text. > * st,lsm6dsx > - Move max_fifo_size into the fifo_ops structure where the other configuration > parameters are found. > * st,st_sensors: > - Reorder to ensure we turn the power off after removing userspace interfaces. > * senseair,sunrise > - Add missing I2C dependency. > * ti,twl6030 > - Small code tidy up. > > ---------------------------------------------------------------- > Alexander Vorwerk (1): > staging: iio: cdc: remove braces from single line if blocks > > Alexandru Ardelean (24): > iio: st_sensors: disable regulators after device unregistration > iio: st_sensors: remove st_sensors_deallocate_trigger() function > iio: st_sensors: remove st_sensors_power_disable() function > iio: st_sensors: remove all driver remove functions > iio: st_sensors: remove reference to parent device object on st_sensor_data > iio: adc: ti-ads8344: convert probe to device-managed > iio: dac: ad7303: convert probe to full device-managed > staging: iio: ad9832: convert probe to device-managed > iio: dac: ad5064: convert probe to full device-managed > iio: gyro: adis16080: use devm_iio_device_register() in probe > iio: light: max44000: use device-managed functions in probe > iio: adc: fsl-imx25-gcq: initialize regulators as needed > iio: inkern: introduce devm_iio_map_array_register() short-hand function > iio: adc: intel_mrfld_adc: convert probe to full device-managed > iio: adc: axp288_adc: convert probe to full device-managed > iio: adc: lp8788_adc: convert probe to full-device managed > iio: adc: da9150-gpadc: convert probe to full-device managed > iio: adc: nau7802: convert probe to full device-managed > iio: adc: max1363: convert probe to full device-managed > iio: adc: rn5t618-adc: use devm_iio_map_array_register() function > iio: adc: berlin2-adc: convert probe to device-managed only > iio: adc: Kconfig: add COMPILE_TEST dep for berlin2-adc > iio: adc: ad7291: convert probe to device-managed only > iio: triggered-buffer: extend support to configure output buffers > > Arnd Bergmann (1): > iio: imx8qxp-adc: mark PM functions as __maybe_unused > > Billy Tsai (13): > dt-bindings: iio: adc: Add ast2600-adc bindings > iio: adc: aspeed: completes the bitfield declare. > iio: adc: aspeed: Keep model data to driver data. > iio: adc: aspeed: Restructure the model data > iio: adc: aspeed: Add vref config function > iio: adc: aspeed: Use model_data to set clk scaler. > iio: adc: aspeed: Use devm_add_action_or_reset. > iio: adc: aspeed: Support ast2600 adc. > iio: adc: aspeed: Fix the calculate error of clock. > iio: adc: aspeed: Add func to set sampling rate. > iio: adc: aspeed: Add compensation phase. > iio: adc: aspeed: Support battery sensing. > iio: adc: aspeed: Get and set trimming data. > > Cai Huoqing (20): > iio: ep93xx: Make use of the helper function devm_platform_ioremap_resource() > iio: dac: stm32-dac: Make use of the helper function devm_platform_ioremap_resource() > iio: adc: rockchip_saradc: Make use of the helper function devm_platform_ioremap_resource() > iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC > dt-bindings: iio: adc: Add binding documentation for NXP IMX8QXP ADC > MAINTAINERS: Add the driver info of the NXP IMX8QXP > iio: dac: ad8801: Make use of the helper function dev_err_probe() > iio: dac: lpc18xx_dac: Make use of the helper function dev_err_probe() > iio: dac: ltc1660: Make use of the helper function dev_err_probe() > iio: dac: ds4424: Make use of the helper function dev_err_probe() > iio: dac: max5821: Make use of the helper function dev_err_probe() > iio: dac: mcp4922: Make use of the helper function dev_err_probe() > iio: dac: stm32-dac: Make use of the helper function dev_err_probe() > iio: dac: ti-dac7311: Make use of the helper function dev_err_probe() > iio: st_sensors: Make use of the helper function dev_err_probe() > iio: st_lsm9ds0: Make use of the helper function dev_err_probe() > iio: health: afe4403: Make use of the helper function dev_err_probe() > iio: health: afe4404: Make use of the helper function dev_err_probe() > iio: light: cm36651: Make use of the helper function dev_err_probe() > iio: light: noa1305: Make use of the helper function dev_err_probe() > > Colin Ian King (1): > iio: adc: aspeed: Fix spelling mistake "battey" -> "battery" > > Dan Carpenter (1): > iio: adc: max1027: fix error code in max1027_wait_eoc() > > Daniel Palmer (2): > iio: imu: inv_mpu6050: Mark acpi match table as maybe unused > iio: accel: mma7660: Mark acpi match table as maybe unused > > David Heidelberg (2): > dt-bindings: iio: kionix,kxcjk1013: driver support interrupts > dt-bindings: iio: magnetometer: asahi-kasei,ak8975 add vid reg > > Eugen Hristev (8): > dt-bindings: iio: adc: at91-sama5d2: add compatible for sama7g5-adc > iio: adc: at91-sama5d2_adc: initialize hardware after clock is started > iio: adc: at91-sama5d2_adc: remove unused definition > iio: adc: at91-sama5d2_adc: convert to platform specific data structures > iio: adc: at91-sama5d2_adc: add support for separate end of conversion registers > iio: adc: at91-sama5d2_adc: add helper for COR register > iio: adc: at91-sama5d2_adc: add support for sama7g5 device > iio: adc: at91-sama5d2_adc: update copyright and authors information > > Florian Boor (2): > iio: adc: ad799x: Implement selecting external reference voltage input on AD7991, AD7995 and AD7999. > dt-bindings: iio: ad779x: Add binding document > > Jacopo Mondi (4): > dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor > iio: ABI: docs: Document Senseair Sunrise ABI > iio: chemical: Add Senseair Sunrise 006-0-007 driver > iio: ABI: Document in_concentration_co2_scale > > Jonathan Cameron (4): > iio: core: Introduce iio_push_to_buffers_with_ts_unaligned() > iio: adc: ti-adc108s102: Fix alignment of buffer pushed to iio buffers. > iio: gyro: mpu3050: Fix alignment and size issues with buffers. > iio: imu: adis16400: Fix buffer alignment requirements. > > Krzysztof Kozlowski (1): > iio: adc: exynos: describe drivers in KConfig > > Lars-Peter Clausen (1): > iio: kfifo-buffer: Add output buffer support > > Len Baker (1): > drivers/iio: Remove all strcpy() uses > > Liam Beguin (5): > iio: adc: ad7949: define and use bitfield names > iio: adc: ad7949: enable use with non 14/16-bit controllers > iio: adc: ad7949: add vref selection support > dt-bindings: iio: adc: ad7949: update voltage reference bindings > iio: adc: ad7949: use devm managed functions > > Lorenzo Bianconi (1): > iio: imu: st_lsm6dsx: move max_fifo_size in st_lsm6dsx_fifo_ops > > Lucas Stankus (2): > dt-bindings: iio: accel: Add binding documentation for ADXL313 > iio: accel: Add driver support for ADXL313 > > Lukas Bulwahn (1): > iio: gyro: remove dead config dependencies on INPUT_MPU3050 > > Matt Ranostay (1): > iio: magnetometer: ak8975: add AK09116 support > > Mihail Chindris (2): > iio: Add output buffer support > drivers:iio:dac:ad5766.c: Add trigger buffer > > Miquel Raynal (16): > iio: adc: max1027: Fix style > iio: adc: max1027: Drop extra warning message > iio: adc: max1027: Drop useless debug messages > iio: adc: max1027: Minimize the number of converted channels > iio: adc: max1027: Rename a helper > iio: adc: max1027: Create a helper to enable/disable the cnvst trigger > iio: adc: max1027: Simplify the _set_trigger_state() helper > iio: adc: max1027: Ensure a default cnvst trigger configuration > iio: adc: max1027: Create a helper to configure the channels to scan > iio: adc: max1027: Prevent single channel accesses during buffer reads > iio: adc: max1027: Separate the IRQ handler from the read logic > iio: adc: max1027: Introduce an end of conversion helper > iio: adc: max1027: Stop requesting a threaded IRQ > iio: adc: max1027: Use the EOC IRQ when populated for single reads > iio: adc: max1027: Allow all kind of triggers to be used > iio: adc: max1027: Don't reject external triggers when there is no IRQ > > Navin Sankar Velliangiri (2): > iio: temperature: Add MAX31865 RTD Support > dt-bindings: iio: temperature: add MAXIM max31865 support > > Nuno Sá (7): > iio: ad5770r: make devicetree property reading consistent > iio: ltc2983: add support for optional reset gpio > iio: ltc2983: fail probe if no channels are given > iio: adis: do not disabe IRQs in 'adis_init()' > iio: adis: handle devices that cannot unmask the drdy pin > iio: adis16475: make use of the new unmasked_drdy flag > iio: adis16460: make use of the new unmasked_drdy flag > > Puranjay Mohan (4): > dt-bindings: iio: accel: Add DT binding doc for ADXL355 > iio: accel: Add driver support for ADXL355 > iio: accel: adxl355: use if(ret) in place of ret < 0 > iio: accel: adxl355: Add triggered buffer support > > Randy Dunlap (1): > iio: chemical: SENSEAIR_SUNRISE_CO2 depends on I2C > > Roan van Dijk (4): > dt-bindings: iio: chemical: sensirion,scd4x: Add yaml description > MAINTAINERS: Add myself as maintainer of the scd4x driver > drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor > iio: documentation: Document scd4x calibration use > > Sean Nyekjaer (2): > iio: accel: fxls8962af: add threshold event handling > iio: accel: fxls8962af: add wake on event > > Tang Bin (1): > iio: adc: twl6030-gpadc: Use the defined variable to clean code > > Uwe Kleine-König (13): > iio: accel: bma400: Make bma400_remove() return void > iio: accel: bmc150: Make bmc150_accel_core_remove() return void > iio: accel: bmi088: Make bmi088_accel_core_remove() return void > iio: accel: kxsd9: Make kxsd9_common_remove() return void > iio: accel: mma7455: Make mma7455_core_remove() return void > iio: dac: ad5380: Make ad5380_remove() return void > iio: dac: ad5446: Make ad5446_remove() return void > iio: dac: ad5592r: Make ad5592r_remove() return void > iio: dac: ad5686: Make ad5686_remove() return void > iio: health: afe4403: Don't return an error in .remove() > iio: magn: hmc5843: Make hmc5843_common_remove() return void > iio: potentiometer: max5487: Don't return an error in .remove() > iio: pressure: ms5611: Make ms5611_remove() return void > > Documentation/ABI/testing/sysfs-bus-iio | 42 ++ > .../ABI/testing/sysfs-bus-iio-chemical-sunrise-co2 | 38 + > Documentation/ABI/testing/sysfs-bus-iio-scd30 | 34 - > .../ABI/testing/sysfs-bus-iio-temperature-max31865 | 20 + > .../devicetree/bindings/iio/accel/adi,adxl313.yaml | 86 +++ > .../devicetree/bindings/iio/accel/adi,adxl355.yaml | 88 +++ > .../bindings/iio/accel/kionix,kxcjk1013.yaml | 3 + > .../devicetree/bindings/iio/adc/adi,ad7949.yaml | 51 +- > .../devicetree/bindings/iio/adc/adi,ad799x.yaml | 73 ++ > .../bindings/iio/adc/aspeed,ast2600-adc.yaml | 100 +++ > .../bindings/iio/adc/atmel,sama5d2-adc.yaml | 1 + > .../bindings/iio/adc/nxp,imx8qxp-adc.yaml | 78 +++ > .../bindings/iio/chemical/senseair,sunrise.yaml | 55 ++ > .../bindings/iio/chemical/sensirion,scd4x.yaml | 46 ++ > .../iio/magnetometer/asahi-kasei,ak8975.yaml | 7 + > .../bindings/iio/temperature/maxim,max31865.yaml | 52 ++ > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > Documentation/driver-api/driver-model/devres.rst | 1 + > MAINTAINERS | 36 + > drivers/iio/accel/Kconfig | 62 ++ > drivers/iio/accel/Makefile | 6 + > drivers/iio/accel/adxl313.h | 54 ++ > drivers/iio/accel/adxl313_core.c | 332 +++++++++ > drivers/iio/accel/adxl313_i2c.c | 66 ++ > drivers/iio/accel/adxl313_spi.c | 92 +++ > drivers/iio/accel/adxl355.h | 21 + > drivers/iio/accel/adxl355_core.c | 765 +++++++++++++++++++++ > drivers/iio/accel/adxl355_i2c.c | 62 ++ > drivers/iio/accel/adxl355_spi.c | 65 ++ > drivers/iio/accel/adxl372.c | 1 + > drivers/iio/accel/bma400.h | 2 +- > drivers/iio/accel/bma400_core.c | 7 +- > drivers/iio/accel/bma400_i2c.c | 4 +- > drivers/iio/accel/bma400_spi.c | 4 +- > drivers/iio/accel/bmc150-accel-core.c | 5 +- > drivers/iio/accel/bmc150-accel-i2c.c | 4 +- > drivers/iio/accel/bmc150-accel-spi.c | 4 +- > drivers/iio/accel/bmc150-accel.h | 2 +- > drivers/iio/accel/bmi088-accel-core.c | 4 +- > drivers/iio/accel/bmi088-accel-spi.c | 4 +- > drivers/iio/accel/bmi088-accel.h | 2 +- > drivers/iio/accel/fxls8962af-core.c | 347 +++++++++- > drivers/iio/accel/kxsd9-i2c.c | 4 +- > drivers/iio/accel/kxsd9-spi.c | 4 +- > drivers/iio/accel/kxsd9.c | 4 +- > drivers/iio/accel/kxsd9.h | 2 +- > drivers/iio/accel/mma7455.h | 2 +- > drivers/iio/accel/mma7455_core.c | 4 +- > drivers/iio/accel/mma7455_i2c.c | 4 +- > drivers/iio/accel/mma7455_spi.c | 4 +- > drivers/iio/accel/mma7660.c | 2 +- > drivers/iio/accel/st_accel_core.c | 31 +- > drivers/iio/accel/st_accel_i2c.c | 23 +- > drivers/iio/accel/st_accel_spi.c | 23 +- > drivers/iio/adc/Kconfig | 18 +- > drivers/iio/adc/Makefile | 1 + > drivers/iio/adc/ad7291.c | 70 +- > drivers/iio/adc/ad7949.c | 254 +++++-- > drivers/iio/adc/ad799x.c | 68 +- > drivers/iio/adc/aspeed_adc.c | 598 +++++++++++++--- > drivers/iio/adc/at91-sama5d2_adc.c | 598 +++++++++++----- > drivers/iio/adc/axp288_adc.c | 28 +- > drivers/iio/adc/berlin2-adc.c | 34 +- > drivers/iio/adc/da9150-gpadc.c | 27 +- > drivers/iio/adc/ep93xx_adc.c | 4 +- > drivers/iio/adc/fsl-imx25-gcq.c | 55 +- > drivers/iio/adc/imx8qxp-adc.c | 494 +++++++++++++ > drivers/iio/adc/intel_mrfld_adc.c | 24 +- > drivers/iio/adc/lp8788_adc.c | 31 +- > drivers/iio/adc/max1027.c | 278 +++++--- > drivers/iio/adc/max1363.c | 82 +-- > drivers/iio/adc/nau7802.c | 50 +- > drivers/iio/adc/rn5t618-adc.c | 13 +- > drivers/iio/adc/rockchip_saradc.c | 4 +- > drivers/iio/adc/ti-adc108s102.c | 11 +- > drivers/iio/adc/ti-ads8344.c | 27 +- > drivers/iio/adc/twl6030-gpadc.c | 6 +- > drivers/iio/buffer/industrialio-triggered-buffer.c | 8 +- > drivers/iio/buffer/kfifo_buf.c | 50 ++ > drivers/iio/chemical/Kconfig | 24 + > drivers/iio/chemical/Makefile | 2 + > drivers/iio/chemical/scd4x.c | 691 +++++++++++++++++++ > drivers/iio/chemical/sunrise_co2.c | 537 +++++++++++++++ > .../iio/common/hid-sensors/hid-sensor-trigger.c | 5 +- > drivers/iio/common/st_sensors/st_sensors_core.c | 48 +- > drivers/iio/common/st_sensors/st_sensors_i2c.c | 1 - > drivers/iio/common/st_sensors/st_sensors_spi.c | 1 - > drivers/iio/common/st_sensors/st_sensors_trigger.c | 53 +- > drivers/iio/dac/ad5064.c | 49 +- > drivers/iio/dac/ad5380.c | 15 +- > drivers/iio/dac/ad5446.c | 12 +- > drivers/iio/dac/ad5592r-base.c | 4 +- > drivers/iio/dac/ad5592r-base.h | 2 +- > drivers/iio/dac/ad5592r.c | 4 +- > drivers/iio/dac/ad5593r.c | 4 +- > drivers/iio/dac/ad5686-spi.c | 4 +- > drivers/iio/dac/ad5686.c | 4 +- > drivers/iio/dac/ad5686.h | 2 +- > drivers/iio/dac/ad5696-i2c.c | 4 +- > drivers/iio/dac/ad5766.c | 42 ++ > drivers/iio/dac/ad5770r.c | 2 +- > drivers/iio/dac/ad7303.c | 47 +- > drivers/iio/dac/ad8801.c | 11 +- > drivers/iio/dac/ds4424.c | 9 +- > drivers/iio/dac/lpc18xx_dac.c | 14 +- > drivers/iio/dac/ltc1660.c | 7 +- > drivers/iio/dac/max5821.c | 9 +- > drivers/iio/dac/mcp4922.c | 7 +- > drivers/iio/dac/stm32-dac-core.c | 18 +- > drivers/iio/dac/ti-dac7311.c | 7 +- > drivers/iio/gyro/Kconfig | 1 - > drivers/iio/gyro/adis16080.c | 11 +- > drivers/iio/gyro/mpu3050-core.c | 24 +- > drivers/iio/gyro/st_gyro_core.c | 27 +- > drivers/iio/gyro/st_gyro_i2c.c | 23 +- > drivers/iio/gyro/st_gyro_spi.c | 23 +- > drivers/iio/health/afe4403.c | 14 +- > drivers/iio/health/afe4404.c | 8 +- > drivers/iio/iio_core.h | 4 + > drivers/iio/imu/adis.c | 17 +- > drivers/iio/imu/adis16400.c | 20 +- > drivers/iio/imu/adis16460.c | 18 +- > drivers/iio/imu/adis16475.c | 19 +- > drivers/iio/imu/adis_trigger.c | 4 + > drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c | 2 +- > drivers/iio/imu/inv_mpu6050/inv_mpu_magn.c | 36 +- > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 4 +- > drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 16 +- > drivers/iio/imu/st_lsm9ds0/st_lsm9ds0.h | 1 - > drivers/iio/imu/st_lsm9ds0/st_lsm9ds0_core.c | 29 +- > drivers/iio/imu/st_lsm9ds0/st_lsm9ds0_i2c.c | 6 - > drivers/iio/imu/st_lsm9ds0/st_lsm9ds0_spi.c | 6 - > drivers/iio/industrialio-buffer.c | 173 ++++- > drivers/iio/industrialio-core.c | 1 + > drivers/iio/inkern.c | 17 + > drivers/iio/light/cm36651.c | 7 +- > drivers/iio/light/max44000.c | 17 +- > drivers/iio/light/noa1305.c | 7 +- > drivers/iio/magnetometer/Kconfig | 2 +- > drivers/iio/magnetometer/ak8975.c | 35 + > drivers/iio/magnetometer/hmc5843.h | 2 +- > drivers/iio/magnetometer/hmc5843_core.c | 4 +- > drivers/iio/magnetometer/hmc5843_i2c.c | 4 +- > drivers/iio/magnetometer/hmc5843_spi.c | 4 +- > drivers/iio/magnetometer/st_magn_core.c | 29 +- > drivers/iio/magnetometer/st_magn_i2c.c | 23 +- > drivers/iio/magnetometer/st_magn_spi.c | 23 +- > drivers/iio/potentiometer/max5487.c | 7 +- > drivers/iio/pressure/ms5611.h | 2 +- > drivers/iio/pressure/ms5611_core.c | 4 +- > drivers/iio/pressure/ms5611_i2c.c | 4 +- > drivers/iio/pressure/ms5611_spi.c | 4 +- > drivers/iio/pressure/st_pressure_core.c | 27 +- > drivers/iio/pressure/st_pressure_i2c.c | 23 +- > drivers/iio/pressure/st_pressure_spi.c | 23 +- > drivers/iio/temperature/Kconfig | 10 + > drivers/iio/temperature/Makefile | 1 + > drivers/iio/temperature/ltc2983.c | 16 + > drivers/iio/temperature/max31865.c | 349 ++++++++++ > drivers/staging/iio/cdc/ad7746.c | 4 +- > drivers/staging/iio/frequency/ad9832.c | 82 +-- > include/linux/iio/buffer.h | 11 + > include/linux/iio/buffer_impl.h | 11 + > include/linux/iio/common/st_sensors.h | 13 - > include/linux/iio/driver.h | 14 + > include/linux/iio/iio-opaque.h | 4 + > include/linux/iio/imu/adis.h | 2 + > include/linux/iio/triggered_buffer.h | 11 +- > 168 files changed, 6998 insertions(+), 1592 deletions(-) > create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-chemical-sunrise-co2 > delete mode 100644 Documentation/ABI/testing/sysfs-bus-iio-scd30 > create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-temperature-max31865 > create mode 100644 Documentation/devicetree/bindings/iio/accel/adi,adxl313.yaml > create mode 100644 Documentation/devicetree/bindings/iio/accel/adi,adxl355.yaml > create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad799x.yaml > create mode 100644 Documentation/devicetree/bindings/iio/adc/aspeed,ast2600-adc.yaml > create mode 100644 Documentation/devicetree/bindings/iio/adc/nxp,imx8qxp-adc.yaml > create mode 100644 Documentation/devicetree/bindings/iio/chemical/senseair,sunrise.yaml > create mode 100644 Documentation/devicetree/bindings/iio/chemical/sensirion,scd4x.yaml > create mode 100644 Documentation/devicetree/bindings/iio/temperature/maxim,max31865.yaml > create mode 100644 drivers/iio/accel/adxl313.h > create mode 100644 drivers/iio/accel/adxl313_core.c > create mode 100644 drivers/iio/accel/adxl313_i2c.c > create mode 100644 drivers/iio/accel/adxl313_spi.c > create mode 100644 drivers/iio/accel/adxl355.h > create mode 100644 drivers/iio/accel/adxl355_core.c > create mode 100644 drivers/iio/accel/adxl355_i2c.c > create mode 100644 drivers/iio/accel/adxl355_spi.c > create mode 100644 drivers/iio/adc/imx8qxp-adc.c > create mode 100644 drivers/iio/chemical/scd4x.c > create mode 100644 drivers/iio/chemical/sunrise_co2.c > create mode 100644 drivers/iio/temperature/max31865.c
