some comments below...
a link to the datasheet would be nice
> This adds support for PixArt Imagingʼs miniature low power
> optical navigation chip using LASER light source
> enabling digital surface tracking.
>
> This IIO driver allow to read delta position on 2 axis (X and Y).
allows
> The values can be taken through ponctual "read_raw" which will issue
punctual
> a read in the device registers to return the delta between last read/buffering
> or subscribe to the data buffer feed automaticaly by a new value using an
automatica_l_ly
> IIO trigger. The buffer payload is: |32 bits delta X|32 bits delta Y|timestamp|.
> It also provide an IIO trigger which fire when a motion is detected.
provides
fires
> This trigger should be reset after each fire by a simple "read_raw" if you aren't
> in buffer mode.
>
> The possible I2C adresses are 0x73, 0x75 and 0x79.
>
> X and Y axis resolution can be setup independently through module parameter.
really? can't this be done using _SCALE?
>
> The "ot" directory is added to coutain Optical Tracker drivers.
contain
how is this thing different from a mouse device?
>
> Signed-off-by: Alexandre Mergnat <amergnat@xxxxxxxxxxxx>
> ---
> drivers/iio/Kconfig | 1 +
> drivers/iio/Makefile | 1 +
> drivers/iio/ot/Kconfig | 16 ++
> drivers/iio/ot/Makefile | 6 +
> drivers/iio/ot/pat9125.c | 487 +++++++++++++++++++++++++++++++++++++++
> 5 files changed, 511 insertions(+)
> create mode 100644 drivers/iio/ot/Kconfig
> create mode 100644 drivers/iio/ot/Makefile
> create mode 100644 drivers/iio/ot/pat9125.c
>
> diff --git a/drivers/iio/Kconfig b/drivers/iio/Kconfig
> index d08aeb41cd07..bdf1bd061168 100644
> --- a/drivers/iio/Kconfig
> +++ b/drivers/iio/Kconfig
> @@ -86,6 +86,7 @@ source "drivers/iio/light/Kconfig"
> source "drivers/iio/magnetometer/Kconfig"
> source "drivers/iio/multiplexer/Kconfig"
> source "drivers/iio/orientation/Kconfig"
> +source "drivers/iio/ot/Kconfig"
> if IIO_TRIGGER
> source "drivers/iio/trigger/Kconfig"
> endif #IIO_TRIGGER
> diff --git a/drivers/iio/Makefile b/drivers/iio/Makefile
> index cb5993251381..fdda2e185005 100644
> --- a/drivers/iio/Makefile
> +++ b/drivers/iio/Makefile
> @@ -32,6 +32,7 @@ obj-y += light/
> obj-y += magnetometer/
> obj-y += multiplexer/
> obj-y += orientation/
> +obj-y += ot/
> obj-y += potentiometer/
> obj-y += potentiostat/
> obj-y += pressure/
> diff --git a/drivers/iio/ot/Kconfig b/drivers/iio/ot/Kconfig
> new file mode 100644
> index 000000000000..3d17fdaa06ed
> --- /dev/null
> +++ b/drivers/iio/ot/Kconfig
> @@ -0,0 +1,16 @@
> +#
> +# Optical tracker sensors
> +#
> +# When adding new entries keep the list in alphabetical order
> +
> +menu "Optical tracker sensors"
> +
> +config PAT9125
> + tristate "Optical tracker PAT9125 I2C driver"
> + depends on I2C
> + select IIO_BUFFER
> + help
> + Say yes here to build support for PAT9125 optical tracker
> + sensors.
> +
> +endmenu
> diff --git a/drivers/iio/ot/Makefile b/drivers/iio/ot/Makefile
> new file mode 100644
> index 000000000000..cf294917ae2c
> --- /dev/null
> +++ b/drivers/iio/ot/Makefile
> @@ -0,0 +1,6 @@
> +#
> +# Makefile for industrial I/O Optical tracker sensor drivers
> +#
> +
> +# When adding new entries keep the list in alphabetical order
> +obj-$(CONFIG_PAT9125) += pat9125.o
> diff --git a/drivers/iio/ot/pat9125.c b/drivers/iio/ot/pat9125.c
> new file mode 100644
> index 000000000000..48c1651b4e6a
> --- /dev/null
> +++ b/drivers/iio/ot/pat9125.c
> @@ -0,0 +1,487 @@
> +// SPDX-License-Identifier: (GPL-2.0)
> +/*
> + * Copyright (C) 2019 BayLibre, SAS
> + * Author: Alexandre Mergnat <amergnat@xxxxxxxxxxxx>
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/i2c.h>
> +#include <linux/iio/iio.h>
> +#include <linux/iio/sysfs.h>
> +#include <linux/iio/events.h>
> +#include <linux/iio/buffer.h>
> +#include <linux/iio/trigger.h>
> +#include <linux/iio/trigger_consumer.h>
> +#include <linux/iio/triggered_buffer.h>
> +#include <linux/iio/kfifo_buf.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +
> +/* I2C Address function to ID pin*/
> +#define PAT9125_I2C_ADDR_HI 0x73
> +#define PAT9125_I2C_ADDR_LO 0x75
> +#define PAT9125_I2C_ADDR_NC 0x79
> +
> +/* Registers */
> +#define PAT9125_PRD_ID1_REG 0x00
> +#define PAT9125_PRD_ID2_REG 0x01
> +#define PAT9125_MOTION_STATUS_REG 0x02
> +#define PAT9125_DELTA_X_LO_REG 0x03
> +#define PAT9125_DELTA_Y_LO_REG 0x04
> +#define PAT9125_OP_MODE_REG 0x05
> +#define PAT9125_CONFIG_REG 0x06
> +#define PAT9125_WRITE_PROTEC_REG 0x09
> +#define PAT9125_SLEEP1_REG 0x0A
> +#define PAT9125_SLEEP2_REG 0x0B
> +#define PAT9125_RES_X_REG 0x0D
> +#define PAT9125_RES_Y_REG 0x0E
> +#define PAT9125_DELTA_XY_HI_REG 0x12
> +#define PAT9125_SHUTER_REG 0x14
> +#define PAT9125_FRAME_AVG_REG 0x17
> +#define PAT9125_ORIENTATION_REG 0x19
> +
> +/* Bits */
> +#define PAT9125_VALID_MOTION_DATA_BIT 0x80
> +#define PAT9125_RESET_BIT 0x80
could use BIT()
> +
> +/* Registers' values */
> +#define PAT9125_SENSOR_ID_VAL 0x31
> +#define PAT9125_DISABLE_WRITE_PROTECT_VAL 0x5A
> +#define PAT9125_ENABLE_WRITE_PROTECT_VAL 0x00
> +#define PAT9125_CPI_RESOLUTION_X_VAL 0x65
> +#define PAT9125_CPI_RESOLUTION_Y_VAL 0xFF
> +
> +/* Default Value of sampled value size */
> +#define PAT9125_SAMPLED_VAL_BIT_SIZE 12
> +
> +struct pat9125_data {
> + struct regmap *regmap;
> + struct iio_trigger *indio_trig; /* Motion detection */
> + s64 ts; /* Timestamp */
> + s32 delta_x;
> + s32 delta_y;
> + s32 motion_detected;
> + bool buffer_mode;
> +};
> +
> +static u8 x_resolution = 0x14;
> +module_param(x_resolution, byte, 0644);
> +MODULE_PARM_DESC(x_resolution, "CPI resolution setting for X axis.");
> +
> +static u8 y_resolution = 0x14;
> +module_param(y_resolution, byte, 0644);
> +MODULE_PARM_DESC(y_resolution, "CPI resolution setting for Y axis.");
I think these should be exposed as IIO _SCALE
> +
> +static const struct iio_event_spec pat9125_event = {
> + .type = IIO_EV_TYPE_THRESH,
> + .dir = IIO_EV_DIR_RISING,
> + .mask_separate = BIT(IIO_EV_INFO_VALUE),
> +};
> +
> +static const struct iio_chan_spec pat9125_channels[] = {
> + {
> + .type = IIO_DISTANCE,
> + .modified = 1,
> + .channel2 = IIO_MOD_X,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
> + .scan_index = 0,
> + .scan_type = {
> + .sign = 's', \
> + .realbits = 32, \
> + .storagebits = 32, \
> + .shift = 0, \
no need to specify shift = 0
> + .endianness = IIO_LE, \
> + },
> + .event_spec = &pat9125_event,
> + .num_event_specs = 1,
> + },
> + {
> + .type = IIO_DISTANCE,
> + .modified = 1,
> + .channel2 = IIO_MOD_Y,
> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
> + .scan_index = 1,
> + .scan_type = {
> + .sign = 's', \
> + .realbits = 32, \
> + .storagebits = 32, \
> + .shift = 0, \
> + .endianness = IIO_LE, \
endianness should be IIO_CPU, no _LE
data is handled by _read_delta() and happily used in arithmetic; maybe
there is endianness conversion missing in the regmap setup
> + },
> + .event_spec = &pat9125_event,
> + .num_event_specs = 1,
> + },
> + IIO_CHAN_SOFT_TIMESTAMP(2),
> +};
> +
> +static int pat9125_read_delta(struct pat9125_data *data)
> +{
> + struct regmap *regmap = data->regmap;
> + int status = 0;
> + int val_x = 0;
> + int val_y = 0;
> + int val_high_nibbles = 0;
> + int old_motion_status;
> + int ret;
> +
> + old_motion_status = data->motion_detected;
> + data->motion_detected = 0;
> + ret = regmap_read(regmap, PAT9125_MOTION_STATUS_REG, &status);
> + if (ret < 0) {
> + data->motion_detected = old_motion_status;
> + return ret;
> + }
> +
> + /* Check if motion is detected */
> + if (status & PAT9125_VALID_MOTION_DATA_BIT) {
> + ret = regmap_read(regmap, PAT9125_DELTA_X_LO_REG, &val_x);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_read(regmap, PAT9125_DELTA_Y_LO_REG, &val_y);
> + if (ret < 0)
> + return ret;
> +
> + ret = regmap_read(regmap, PAT9125_DELTA_XY_HI_REG, &val_high_nibbles);
> + if (ret < 0)
> + return ret;
> +
> + val_x |= (val_high_nibbles << 4) & 0xF00;
> + val_y |= (val_high_nibbles << 8) & 0xF00;
> +
> + val_x = sign_extend32(val_x,
> + PAT9125_SAMPLED_VAL_BIT_SIZE - 1);
> +
> + val_y = sign_extend32(val_y,
> + PAT9125_SAMPLED_VAL_BIT_SIZE - 1);
> +
> +
> + data->delta_x += val_x;
> + data->delta_y += val_y;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * pat9125_read_raw() - Sample and return the value(s)
> + * function to the associated channel info enum.
> + **/
> +static int pat9125_read_raw(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + struct pat9125_data *data = iio_priv(indio_dev);
> + int ret;
> +
> + switch (mask) {
> + case IIO_CHAN_INFO_RAW:
> + ret = pat9125_read_delta(data);
> + if (ret)
> + return ret;
> + switch (chan->channel2) {
> + case IIO_MOD_X:
> + *val = data->delta_x;
> + data->delta_x = 0;
> + break;
> + case IIO_MOD_Y:
> + *val = data->delta_y;
> + data->delta_y = 0;
> + break;
> + default:
> + return -EINVAL;
> + }
> + return IIO_VAL_INT;
I'd move the
return IIO_VAL_INT up, instead of the break;
> + default:
> + return -EINVAL;
> + }
> + return -EINVAL;
no need, dead code
> +}
> +
> +static irqreturn_t pat9125_trigger_handler(int irq, void *p)
> +{
> + struct iio_poll_func *pf = p;
> + struct iio_dev *indio_dev = pf->indio_dev;
> + struct pat9125_data *data = iio_priv(indio_dev);
> + u8 buf[16]; /* Payload: Delta_X (4) | Delta_Y (4) | Timestamp (8) */
> + int ret;
> +
> + ret = pat9125_read_delta(data);
> + if (ret) {
> + iio_trigger_notify_done(indio_dev->trig);
> + return IRQ_NONE;
> + }
> + data->ts = iio_get_time_ns(indio_dev);
> + memcpy(&buf[0], &data->delta_x, 4);
> + memcpy(&buf[4], &data->delta_y, 4);
why memcpy?
4 == sizeof(s32)
> + data->delta_x = 0;
> + data->delta_y = 0;
> + iio_push_to_buffers_with_timestamp(indio_dev, buf, data->ts);
> + iio_trigger_notify_done(indio_dev->trig);
> + return IRQ_HANDLED;
> +}
> +
> +/**
> + * pat9125_event_handler() - handling ring and non ring events
> + * @irq: The irq being handled.
> + * @private: struct iio_device pointer for the device.
> + */
> +static irqreturn_t pat9125_event_handler(int irq, void *private)
> +{
> + struct iio_dev *indio_dev = private;
> + struct pat9125_data *data = iio_priv(indio_dev);
> +
> + iio_trigger_poll(data->indio_trig);
> + data->motion_detected = 1;
> + return IRQ_HANDLED;
> +}
> +
> +static int pat9125_buffer_postenable(struct iio_dev *indio_dev)
> +{
> + struct pat9125_data *data = iio_priv(indio_dev);
> + int ret = 0;
> +
> + ret = iio_triggered_buffer_postenable(indio_dev);
> + if (ret)
> + return ret;
> + data->buffer_mode = true;
> + /* Release IRQ on the chip */
> + return pat9125_read_delta(data);
> +}
> +
> +static int pat9125_buffer_predisable(struct iio_dev *indio_dev)
> +{
> + struct pat9125_data *data = iio_priv(indio_dev);
> +
> + data->buffer_mode = false;
> + return iio_triggered_buffer_predisable(indio_dev);
> +}
> +
> +static const struct iio_buffer_setup_ops pat9125_buffer_ops = {
> + .preenable = NULL,
> + .postenable = pat9125_buffer_postenable,
> + .predisable = pat9125_buffer_predisable,
> + .postdisable = NULL,
> +};
> +
> +
> +static const struct regmap_config pat9125_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> +};
> +
> +static const struct iio_info pat9125_info = {
> + .read_raw = pat9125_read_raw,
> +};
> +
> +/*
> + * To avoid infinite loop in "iio_trigger_notify_done",
> + * try_reenable must return 0 when it isn't in buffer mode.
> + * This implementation avoid corner case.
> + */
> +static int pat9125_trig_try_reen(struct iio_trigger *trig)
maybe spell out try_reenable to match comment above
> +{
> + struct pat9125_data *data = iio_trigger_get_drvdata(trig);
> +
> + if (data->buffer_mode)
> + return data->motion_detected;
> + else
> + return 0;
> +}
> +
> +static const struct iio_trigger_ops pat9125_trigger_ops = {
> + .try_reenable = pat9125_trig_try_reen,
> +};
> +
> +static int pat9125_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct pat9125_data *data;
> + struct iio_dev *indio_dev;
> + int ret, sensor_pid;
> +
> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
> + if (!indio_dev) {
> + dev_err(&client->dev, "IIO device allocation failed");
I'd rather remove the error message, it probably will never happen :)
dev_err() wants \n at the end of the message (here and elsewhere)
> + return -ENOMEM;
> + }
> +
> + data = iio_priv(indio_dev);
> +
> + indio_dev->dev.parent = &client->dev;
> + indio_dev->name = id->name;
> + indio_dev->channels = pat9125_channels;
> + indio_dev->num_channels = ARRAY_SIZE(pat9125_channels);
> + indio_dev->info = &pat9125_info;
> + indio_dev->modes = INDIO_DIRECT_MODE;
> + data->motion_detected = 0;
> + data->buffer_mode = false;
> +
> + ret = iio_triggered_buffer_setup(indio_dev, NULL, pat9125_trigger_handler,
> + &pat9125_buffer_ops);
> + if (ret) {
> + dev_err(&client->dev, "unable to setup triggered buffer\n");
> + return ret;
> + }
> +
> + data->indio_trig = devm_iio_trigger_alloc(&client->dev, "%s-dev%d",
> + indio_dev->name, indio_dev->id);
> + if (!data->indio_trig) {
> + return -ENOMEM;
> + }
> + data->indio_trig->dev.parent = &client->dev;
> + data->indio_trig->ops = &pat9125_trigger_ops;
> + iio_trigger_set_drvdata(data->indio_trig, data);
> + ret = iio_trigger_register(data->indio_trig);
> + if (ret) {
> + iio_trigger_unregister(data->indio_trig);
no need to unregister trigger if trigger_register() failed?
> + return ret;
> + }
> +
> + data->regmap = devm_regmap_init_i2c(client, &pat9125_regmap_config);
> + if (IS_ERR(data->regmap)) {
> + dev_err(&client->dev, "regmap init failed %ld",
> + PTR_ERR(data->regmap));
> + return PTR_ERR(data->regmap);
> + }
> +
> + /* Check device ID */
> + ret = regmap_read(data->regmap, PAT9125_PRD_ID1_REG, &sensor_pid);
> + if (ret < 0) {
> + dev_err(&client->dev, "register 0x%x access failed %d",
> + PAT9125_PRD_ID1_REG, ret);
> + return ret;
> + }
> + if (sensor_pid != PAT9125_SENSOR_ID_VAL)
> + return -ENODEV;
> +
> + /*
> + * Software reset
> + */
single line comment?
> + ret = regmap_write_bits(data->regmap,
> + PAT9125_CONFIG_REG,
> + PAT9125_RESET_BIT,
> + 1);
> + if (ret < 0) {
> + dev_err(&client->dev, "register 0x%x access failed %d",
> + PAT9125_CONFIG_REG, ret);
> + return ret;
> + }
> +
> + msleep(20);
> +
> + ret = regmap_write(data->regmap,
> + PAT9125_WRITE_PROTEC_REG,
> + PAT9125_DISABLE_WRITE_PROTECT_VAL);
> + if (ret < 0) {
> + dev_err(&client->dev, "register 0x%x access failed %d",
> + PAT9125_WRITE_PROTEC_REG, ret);
> + return ret;
> + }
> + ret = regmap_write(data->regmap,
> + PAT9125_RES_X_REG,
> + x_resolution);
> + if (ret < 0) {
> + dev_err(&client->dev, "register 0x%x access failed %d",
> + PAT9125_RES_X_REG, ret);
> + return ret;
> + }
> + ret = regmap_write(data->regmap,
> + PAT9125_RES_Y_REG,
> + y_resolution);
> + if (ret < 0) {
> + dev_err(&client->dev, "register 0x%x access failed %d",
> + PAT9125_RES_Y_REG, ret);
> + return ret;
> + }
> + /* Enable write protection */
> + ret = regmap_write(data->regmap,
> + PAT9125_WRITE_PROTEC_REG,
> + PAT9125_ENABLE_WRITE_PROTECT_VAL);
> + if (ret < 0) {
> + dev_err(&client->dev, "register 0x%x access failed %d",
> + PAT9125_WRITE_PROTEC_REG, ret);
> + return ret;
> + }
> +
> + ret = devm_iio_device_register(&client->dev, indio_dev);
> + if (ret) {
> + dev_err(&client->dev, "IIO device register failed");
> + iio_triggered_buffer_cleanup(indio_dev);
> + return ret;
> + }
> +
> + i2c_set_clientdata(client, indio_dev);
> +
> + dev_info(&client->dev, "%s: sensor '%s'\n",
> + dev_name(&indio_dev->dev),
> + client->name);
please avoid log output, it just clutters the log
> +
> + /* Make read to reset motion bit status */
> + ret = pat9125_read_delta(data);
> + if (ret) {
> + dev_err(&client->dev, "Read register failed");
> + return ret;
> + }
> +
> + /* Init GPIO IRQ */
> + if (client->irq) {
> + ret = devm_request_threaded_irq(&client->dev,
> + client->irq,
> + pat9125_event_handler,
> + NULL,
> + IRQF_TRIGGER_FALLING,
> + "pat9125",
> + indio_dev);
> + if (ret) {
> + dev_err(&client->dev, "GPIO IRQ init failed");
> + return ret;
> + }
> + }
> + return 0;
> +}
> +
> +static int pat9125_remove(struct i2c_client *client)
> +{
> + struct iio_dev *indio_dev = devm_iio_device_alloc(&client->dev, sizeof(struct pat9125_data));
> +
> + iio_device_unregister(indio_dev);
> + iio_triggered_buffer_cleanup(indio_dev);
> +
> + dev_info(&client->dev, "PAT9125 removed\n");
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id pat9125_id[] = {
> + { "pat9125", 0 },
> + {}
> +};
> +MODULE_DEVICE_TABLE(i2c, pat9125_id);
> +
> +static const unsigned short normal_i2c[] = {
> + PAT9125_I2C_ADDR_HI,
> + PAT9125_I2C_ADDR_LO,
> + PAT9125_I2C_ADDR_NC,
> + I2C_CLIENT_END
> +};
> +
> +static struct i2c_driver pat9125_driver = {
> + .driver = {
> + .name = "pat9125",
> + },
> + .probe = pat9125_probe,
> + .remove = pat9125_remove,
> + .address_list = normal_i2c,
> + .id_table = pat9125_id,
> +};
> +
> +module_i2c_driver(pat9125_driver);
> +
> +MODULE_AUTHOR("Alexandre Mergnat <amergnat@xxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Optical Tracking sensor");
> +MODULE_LICENSE("GPL");
> \ No newline at end of file
>
--
Peter Meerwald-Stadler
Mobile: +43 664 24 44 418
