+#define INA2XX_CHAN(_type, _index, _address) { \
+ .type = (_type), \
+ .address = (_address), \
+ .indexed = 1, \
+ .channel = (_index), \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
+ .info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+ BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+ .scan_index = (_index), \
+ .scan_type = { \
+ .sign = 'u', \
+ .realbits = 16, \
+ .storagebits = 16, \
+ .endianness = IIO_BE, \
+ } \
+}
+
+/*
+ * Sampling Freq is a consequence of the integration times of
+ * the Voltage channels.
+ */
+#define INA2XX_CHAN_VOLTAGE(_index, _address) { \
+ .type = IIO_VOLTAGE, \
+ .address = (_address), \
+ .indexed = 1, \
+ .channel = (_index), \
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+ BIT(IIO_CHAN_INFO_INT_TIME), \
+ .scan_index = (_index), \
+ .scan_type = { \
+ .sign = 'u', \
+ .realbits = 16, \
+ .storagebits = 16, \
+ .endianness = IIO_BE, \
+ } \
+}
+
+static const struct iio_chan_spec ina2xx_channels[] = {
+ INA2XX_CHAN_VOLTAGE(0, INA2XX_SHUNT_VOLTAGE),
+ INA2XX_CHAN_VOLTAGE(1, INA2XX_BUS_VOLTAGE),
+ INA2XX_CHAN(IIO_CURRENT, 2, INA2XX_CURRENT),
+ INA2XX_CHAN(IIO_POWER, 3, INA2XX_POWER),
+ IIO_CHAN_SOFT_TIMESTAMP(4),
+};
+
+static int ina2xx_work_buffer(struct iio_dev *indio_dev)
+{
+ struct ina2xx_chip_info *chip = iio_priv(indio_dev);
+ unsigned short data[8];
+ int bit, ret, i = 0;
+ unsigned long buffer_us, elapsed_us;
+ s64 time_a, time_b;
+ unsigned int alert;
+
+ time_a = iio_get_time_ns();
+
+ /*
+ * Because the timer thread and the chip conversion clock
+ * are asynchronous, the period difference will eventually
+ * result in reading V[k-1] again, or skip V[k] at time Tk.
+ * In order to resync the timer with the conversion process
+ * we check the ConVersionReadyFlag.
+ * On hardware that supports using the ALERT pin to toggle a
+ * GPIO a triggered buffer could be used instead.
+ * For now, we pay for that extra read of the ALERT register
+ */
+ do {
+ ret = regmap_read(chip->regmap, INA226_ALERT_MASK,
+ &alert);
+ if (ret < 0)
+ return ret;
+
+ alert &= INA266_CVRF;
+ trace_printk("Conversion ready: %d\n", !!alert);
+
+ } while (!alert);
+
+ /*
+ * Single register reads: bulk_read will not work with ina226
+ * as there is no auto-increment of the address register for
+ * data length longer than 16bits.
+ */
+ for_each_set_bit(bit, indio_dev->active_scan_mask,
+ indio_dev->masklength) {
+ unsigned int val;
+
+ ret = regmap_read(chip->regmap,
+ INA2XX_SHUNT_VOLTAGE + bit, &val);
+ if (ret < 0)
+ return ret;
+
+ data[i++] = val;
