Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@xxxxxx>
Cc: Denis Ciocca <denis.ciocca@xxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
ChangeLog v2->v3:
- Fix the missing IHL (IEA) setting for the LSM303AGR
magnetometer
- Drop the active low settings for the gyros: these have
DRDY on INT2 and that does not support setting polarity or
open drain. Insert an explanatory comment instead.
ChangeLog v1->v2:
- Rebased to come first in the series independently of the
request_any_context_irq() change.
- Fixed some errorpath issues found by Denis, including a
cleanup to return out directly on the first error.
---
drivers/iio/accel/st_accel_core.c | 16 +++++++
drivers/iio/common/st_sensors/st_sensors_core.c | 6 +--
drivers/iio/common/st_sensors/st_sensors_core.h | 8 ++++
drivers/iio/common/st_sensors/st_sensors_trigger.c | 52 +++++++++++++++++-----
drivers/iio/gyro/st_gyro_core.c | 15 +++++++
drivers/iio/magnetometer/st_magn_core.c | 4 ++
drivers/iio/pressure/st_pressure_core.c | 8 ++++
include/linux/iio/common/st_sensors.h | 4 ++
8 files changed, 100 insertions(+), 13 deletions(-)
create mode 100644 drivers/iio/common/st_sensors/st_sensors_core.h
diff --git a/drivers/iio/accel/st_accel_core.c b/drivers/iio/accel/st_accel_core.c
index 197a08b4e2f3..1132224cbc10 100644
--- a/drivers/iio/accel/st_accel_core.c
+++ b/drivers/iio/accel/st_accel_core.c
@@ -67,6 +67,8 @@
#define ST_ACCEL_1_DRDY_IRQ_ADDR 0x22
#define ST_ACCEL_1_DRDY_IRQ_INT1_MASK 0x10
#define ST_ACCEL_1_DRDY_IRQ_INT2_MASK 0x08
+#define ST_ACCEL_1_IHL_IRQ_ADDR 0x25
+#define ST_ACCEL_1_IHL_IRQ_MASK 0x02
#define ST_ACCEL_1_MULTIREAD_BIT true
/* CUSTOM VALUES FOR SENSOR 2 */
@@ -92,6 +94,8 @@
#define ST_ACCEL_2_DRDY_IRQ_ADDR 0x22
#define ST_ACCEL_2_DRDY_IRQ_INT1_MASK 0x02
#define ST_ACCEL_2_DRDY_IRQ_INT2_MASK 0x10
+#define ST_ACCEL_2_IHL_IRQ_ADDR 0x22
+#define ST_ACCEL_2_IHL_IRQ_MASK 0x80
#define ST_ACCEL_2_MULTIREAD_BIT true
/* CUSTOM VALUES FOR SENSOR 3 */
@@ -125,6 +129,8 @@
#define ST_ACCEL_3_DRDY_IRQ_ADDR 0x23
#define ST_ACCEL_3_DRDY_IRQ_INT1_MASK 0x80
#define ST_ACCEL_3_DRDY_IRQ_INT2_MASK 0x00
+#define ST_ACCEL_3_IHL_IRQ_ADDR 0x23
+#define ST_ACCEL_3_IHL_IRQ_MASK 0x40
#define ST_ACCEL_3_IG1_EN_ADDR 0x23
#define ST_ACCEL_3_IG1_EN_MASK 0x08
#define ST_ACCEL_3_MULTIREAD_BIT false
@@ -169,6 +175,8 @@
#define ST_ACCEL_5_DRDY_IRQ_ADDR 0x22
#define ST_ACCEL_5_DRDY_IRQ_INT1_MASK 0x04
#define ST_ACCEL_5_DRDY_IRQ_INT2_MASK 0x20
+#define ST_ACCEL_5_IHL_IRQ_ADDR 0x22
+#define ST_ACCEL_5_IHL_IRQ_MASK 0x80
#define ST_ACCEL_5_IG1_EN_ADDR 0x21
#define ST_ACCEL_5_IG1_EN_MASK 0x08
#define ST_ACCEL_5_MULTIREAD_BIT false
@@ -291,6 +299,8 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
.addr = ST_ACCEL_1_DRDY_IRQ_ADDR,
.mask_int1 = ST_ACCEL_1_DRDY_IRQ_INT1_MASK,
.mask_int2 = ST_ACCEL_1_DRDY_IRQ_INT2_MASK,
+ .addr_ihl = ST_ACCEL_1_IHL_IRQ_ADDR,
+ .mask_ihl = ST_ACCEL_1_IHL_IRQ_MASK,
},
.multi_read_bit = ST_ACCEL_1_MULTIREAD_BIT,
.bootime = 2,
@@ -354,6 +364,8 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
.addr = ST_ACCEL_2_DRDY_IRQ_ADDR,
.mask_int1 = ST_ACCEL_2_DRDY_IRQ_INT1_MASK,
.mask_int2 = ST_ACCEL_2_DRDY_IRQ_INT2_MASK,
+ .addr_ihl = ST_ACCEL_2_IHL_IRQ_ADDR,
+ .mask_ihl = ST_ACCEL_2_IHL_IRQ_MASK,
},
.multi_read_bit = ST_ACCEL_2_MULTIREAD_BIT,
.bootime = 2,
@@ -429,6 +441,8 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
.addr = ST_ACCEL_3_DRDY_IRQ_ADDR,
.mask_int1 = ST_ACCEL_3_DRDY_IRQ_INT1_MASK,
.mask_int2 = ST_ACCEL_3_DRDY_IRQ_INT2_MASK,
+ .addr_ihl = ST_ACCEL_3_IHL_IRQ_ADDR,
+ .mask_ihl = ST_ACCEL_3_IHL_IRQ_MASK,
.ig1 = {
.en_addr = ST_ACCEL_3_IG1_EN_ADDR,
.en_mask = ST_ACCEL_3_IG1_EN_MASK,
@@ -536,6 +550,8 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
.addr = ST_ACCEL_5_DRDY_IRQ_ADDR,
.mask_int1 = ST_ACCEL_5_DRDY_IRQ_INT1_MASK,
.mask_int2 = ST_ACCEL_5_DRDY_IRQ_INT2_MASK,
+ .addr_ihl = ST_ACCEL_5_IHL_IRQ_ADDR,
+ .mask_ihl = ST_ACCEL_5_IHL_IRQ_MASK,
},
.multi_read_bit = ST_ACCEL_5_MULTIREAD_BIT,
.bootime = 2, /* guess */
diff --git a/drivers/iio/common/st_sensors/st_sensors_core.c b/drivers/iio/common/st_sensors/st_sensors_core.c
index 25258e2c1a82..ed6f54d5c932 100644
--- a/drivers/iio/common/st_sensors/st_sensors_core.c
+++ b/drivers/iio/common/st_sensors/st_sensors_core.c
@@ -17,7 +17,7 @@
#include <linux/of.h>
#include <asm/unaligned.h>
#include <linux/iio/common/st_sensors.h>
-
+#include "st_sensors_core.h"
#define ST_SENSORS_WAI_ADDRESS 0x0f
@@ -26,8 +26,8 @@ static inline u32 st_sensors_get_unaligned_le24(const u8 *p)
return (s32)((p[0] | p[1] << 8 | p[2] << 16) << 8) >> 8;
}
-static int st_sensors_write_data_with_mask(struct iio_dev *indio_dev,
- u8 reg_addr, u8 mask, u8 data)
+int st_sensors_write_data_with_mask(struct iio_dev *indio_dev,
+ u8 reg_addr, u8 mask, u8 data)
{
int err;
u8 new_data;
diff --git a/drivers/iio/common/st_sensors/st_sensors_core.h b/drivers/iio/common/st_sensors/st_sensors_core.h
new file mode 100644
index 000000000000..cd88098ff6f1
--- /dev/null
+++ b/drivers/iio/common/st_sensors/st_sensors_core.h
@@ -0,0 +1,8 @@
+/*
+ * Local functions in the ST Sensors core
+ */
+#ifndef __ST_SENSORS_CORE_H
+#define __ST_SENSORS_CORE_H
+int st_sensors_write_data_with_mask(struct iio_dev *indio_dev,
+ u8 reg_addr, u8 mask, u8 data);
+#endif
diff --git a/drivers/iio/common/st_sensors/st_sensors_trigger.c b/drivers/iio/common/st_sensors/st_sensors_trigger.c
index 3c0aa17d753f..54115ccdada2 100644
--- a/drivers/iio/common/st_sensors/st_sensors_trigger.c
+++ b/drivers/iio/common/st_sensors/st_sensors_trigger.c
@@ -14,33 +14,66 @@
#include <linux/iio/iio.h>
#include <linux/iio/trigger.h>
#include <linux/interrupt.h>
-
#include <linux/iio/common/st_sensors.h>
-
+#include "st_sensors_core.h"
int st_sensors_allocate_trigger(struct iio_dev *indio_dev,
const struct iio_trigger_ops *trigger_ops)
{
- int err;
+ int err, irq;
struct st_sensor_data *sdata = iio_priv(indio_dev);
+ unsigned long irq_trig;
sdata->trig = iio_trigger_alloc("%s-dev%d",
indio_dev->name, indio_dev->id);
if (sdata->trig == NULL) {
- err = -ENOMEM;
dev_err(&indio_dev->dev, "failed to allocate iio trigger.\n");
- goto iio_trigger_alloc_error;
+ return -ENOMEM;
}
- err = request_threaded_irq(sdata->get_irq_data_ready(indio_dev),
+ irq = sdata->get_irq_data_ready(indio_dev);
+ irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
+ /*
+ * If the IRQ is triggered on falling edge, we need to mark the
+ * interrupt as active low, if the hardware supports this.
+ */
+ if (irq_trig == IRQF_TRIGGER_FALLING) {
+ if (!sdata->sensor_settings->drdy_irq.addr_ihl) {
+ dev_err(&indio_dev->dev,
+ "falling edge specified for IRQ but hardware "
+ "only support rising edge, will request "
+ "rising edge\n");
+ irq_trig = IRQF_TRIGGER_RISING;
+ } else {
+ /* Set up INT active low i.e. falling edge */
+ err = st_sensors_write_data_with_mask(indio_dev,
+ sdata->sensor_settings->drdy_irq.addr_ihl,
+ sdata->sensor_settings->drdy_irq.mask_ihl, 1);
+ if (err < 0)
+ goto iio_trigger_free;
+ dev_info(&indio_dev->dev,
+ "interrupts on the falling edge\n");
+ }
+ } else if (irq_trig == IRQF_TRIGGER_RISING) {
+ dev_info(&indio_dev->dev,
+ "interrupts on the rising edge\n");
+
+ } else {
+ dev_err(&indio_dev->dev,
+ "unsupported IRQ trigger specified (%lx), only "
+ "rising and falling edges supported, enforce "
+ "rising edge\n", irq_trig);
+ irq_trig = IRQF_TRIGGER_RISING;
+ }
+ err = request_threaded_irq(irq,
iio_trigger_generic_data_rdy_poll,
NULL,
- IRQF_TRIGGER_RISING,
+ irq_trig,
sdata->trig->name,
sdata->trig);
if (err) {
dev_err(&indio_dev->dev, "failed to request trigger IRQ.\n");
- goto request_irq_error;
+ goto iio_trigger_free;
}
iio_trigger_set_drvdata(sdata->trig, indio_dev);
@@ -58,9 +91,8 @@ int st_sensors_allocate_trigger(struct iio_dev *indio_dev,
iio_trigger_register_error:
free_irq(sdata->get_irq_data_ready(indio_dev), sdata->trig);
-request_irq_error:
+iio_trigger_free:
iio_trigger_free(sdata->trig);
-iio_trigger_alloc_error:
return err;
}
EXPORT_SYMBOL(st_sensors_allocate_trigger);
diff --git a/drivers/iio/gyro/st_gyro_core.c b/drivers/iio/gyro/st_gyro_core.c
index 02eddcebeea3..110f95b6e52f 100644
--- a/drivers/iio/gyro/st_gyro_core.c
+++ b/drivers/iio/gyro/st_gyro_core.c
@@ -185,6 +185,11 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = {
.drdy_irq = {
.addr = ST_GYRO_1_DRDY_IRQ_ADDR,
.mask_int2 = ST_GYRO_1_DRDY_IRQ_INT2_MASK,
+ /*
+ * The sensor has IHL (active low) and open
+ * drain settings, but only for INT1 and not
+ * for the DRDY line on INT2.
+ */
},
.multi_read_bit = ST_GYRO_1_MULTIREAD_BIT,
.bootime = 2,
@@ -248,6 +253,11 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = {
.drdy_irq = {
.addr = ST_GYRO_2_DRDY_IRQ_ADDR,
.mask_int2 = ST_GYRO_2_DRDY_IRQ_INT2_MASK,
+ /*
+ * The sensor has IHL (active low) and open
+ * drain settings, but only for INT1 and not
+ * for the DRDY line on INT2.
+ */
},
.multi_read_bit = ST_GYRO_2_MULTIREAD_BIT,
.bootime = 2,
@@ -307,6 +317,11 @@ static const struct st_sensor_settings st_gyro_sensors_settings[] = {
.drdy_irq = {
.addr = ST_GYRO_3_DRDY_IRQ_ADDR,
.mask_int2 = ST_GYRO_3_DRDY_IRQ_INT2_MASK,
+ /*
+ * The sensor has IHL (active low) and open
+ * drain settings, but only for INT1 and not
+ * for the DRDY line on INT2.
+ */
},
.multi_read_bit = ST_GYRO_3_MULTIREAD_BIT,
.bootime = 2,
diff --git a/drivers/iio/magnetometer/st_magn_core.c b/drivers/iio/magnetometer/st_magn_core.c
index b27f0146647b..501f858df413 100644
--- a/drivers/iio/magnetometer/st_magn_core.c
+++ b/drivers/iio/magnetometer/st_magn_core.c
@@ -175,6 +175,8 @@
#define ST_MAGN_3_BDU_MASK 0x10
#define ST_MAGN_3_DRDY_IRQ_ADDR 0x62
#define ST_MAGN_3_DRDY_INT_MASK 0x01
+#define ST_MAGN_3_IHL_IRQ_ADDR 0x63
+#define ST_MAGN_3_IHL_IRQ_MASK 0x04
#define ST_MAGN_3_FS_AVL_15000_GAIN 1500
#define ST_MAGN_3_MULTIREAD_BIT false
#define ST_MAGN_3_OUT_X_L_ADDR 0x68
@@ -480,6 +482,8 @@ static const struct st_sensor_settings st_magn_sensors_settings[] = {
.drdy_irq = {
.addr = ST_MAGN_3_DRDY_IRQ_ADDR,
.mask_int1 = ST_MAGN_3_DRDY_INT_MASK,
+ .addr_ihl = ST_MAGN_3_IHL_IRQ_ADDR,
+ .mask_ihl = ST_MAGN_3_IHL_IRQ_MASK,
},
.multi_read_bit = ST_MAGN_3_MULTIREAD_BIT,
.bootime = 2,
diff --git a/drivers/iio/pressure/st_pressure_core.c b/drivers/iio/pressure/st_pressure_core.c
index b39a2fb0671c..172393ad34af 100644
--- a/drivers/iio/pressure/st_pressure_core.c
+++ b/drivers/iio/pressure/st_pressure_core.c
@@ -62,6 +62,8 @@
#define ST_PRESS_LPS331AP_DRDY_IRQ_ADDR 0x22
#define ST_PRESS_LPS331AP_DRDY_IRQ_INT1_MASK 0x04
#define ST_PRESS_LPS331AP_DRDY_IRQ_INT2_MASK 0x20
+#define ST_PRESS_LPS331AP_IHL_IRQ_ADDR 0x22
+#define ST_PRESS_LPS331AP_IHL_IRQ_MASK 0x80
#define ST_PRESS_LPS331AP_MULTIREAD_BIT true
#define ST_PRESS_LPS331AP_TEMP_OFFSET 42500
@@ -100,6 +102,8 @@
#define ST_PRESS_LPS25H_DRDY_IRQ_ADDR 0x23
#define ST_PRESS_LPS25H_DRDY_IRQ_INT1_MASK 0x01
#define ST_PRESS_LPS25H_DRDY_IRQ_INT2_MASK 0x10
+#define ST_PRESS_LPS25H_IHL_IRQ_ADDR 0x22
+#define ST_PRESS_LPS25H_IHL_IRQ_MASK 0x80
#define ST_PRESS_LPS25H_MULTIREAD_BIT true
#define ST_PRESS_LPS25H_TEMP_OFFSET 42500
#define ST_PRESS_LPS25H_OUT_XL_ADDR 0x28
@@ -220,6 +224,8 @@ static const struct st_sensor_settings st_press_sensors_settings[] = {
.addr = ST_PRESS_LPS331AP_DRDY_IRQ_ADDR,
.mask_int1 = ST_PRESS_LPS331AP_DRDY_IRQ_INT1_MASK,
.mask_int2 = ST_PRESS_LPS331AP_DRDY_IRQ_INT2_MASK,
+ .addr_ihl = ST_PRESS_LPS331AP_IHL_IRQ_ADDR,
+ .mask_ihl = ST_PRESS_LPS331AP_IHL_IRQ_MASK,
},
.multi_read_bit = ST_PRESS_LPS331AP_MULTIREAD_BIT,
.bootime = 2,
@@ -304,6 +310,8 @@ static const struct st_sensor_settings st_press_sensors_settings[] = {
.addr = ST_PRESS_LPS25H_DRDY_IRQ_ADDR,
.mask_int1 = ST_PRESS_LPS25H_DRDY_IRQ_INT1_MASK,
.mask_int2 = ST_PRESS_LPS25H_DRDY_IRQ_INT2_MASK,
+ .addr_ihl = ST_PRESS_LPS25H_IHL_IRQ_ADDR,
+ .mask_ihl = ST_PRESS_LPS25H_IHL_IRQ_MASK,
},
.multi_read_bit = ST_PRESS_LPS25H_MULTIREAD_BIT,
.bootime = 2,
diff --git a/include/linux/iio/common/st_sensors.h b/include/linux/iio/common/st_sensors.h
index 2fe939c73cd2..6670c3d25c58 100644
--- a/include/linux/iio/common/st_sensors.h
+++ b/include/linux/iio/common/st_sensors.h
@@ -119,6 +119,8 @@ struct st_sensor_bdu {
* @addr: address of the register.
* @mask_int1: mask to enable/disable IRQ on INT1 pin.
* @mask_int2: mask to enable/disable IRQ on INT2 pin.
+ * @addr_ihl: address to enable/disable active low on the INT lines.
+ * @mask_ihl: mask to enable/disable active low on the INT lines.
* struct ig1 - represents the Interrupt Generator 1 of sensors.
* @en_addr: address of the enable ig1 register.
* @en_mask: mask to write the on/off value for enable.
@@ -127,6 +129,8 @@ struct st_sensor_data_ready_irq {
u8 addr;
u8 mask_int1;
u8 mask_int2;
+ u8 addr_ihl;
+ u8 mask_ihl;
struct {
u8 en_addr;
u8 en_mask;
--
2.4.3
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
