On Wed, Mar 05, 2014 at 06:35:39PM +0100, Alexandre Belloni wrote:
> The atmel_tsadcc driver is not used anymore, it has been replaced by at91_adc so
> remove it.
>
> Signed-off-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxxxxxxxxx>
Acked-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
> ---
> MAINTAINERS | 6 -
> drivers/input/touchscreen/Kconfig | 12 --
> drivers/input/touchscreen/Makefile | 1 -
> drivers/input/touchscreen/atmel_tsadcc.c | 358 -------------------------------
> 4 files changed, 377 deletions(-)
> delete mode 100644 drivers/input/touchscreen/atmel_tsadcc.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index c6d0e93eff62..134dd63dfa17 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1591,12 +1591,6 @@ S: Supported
> F: drivers/misc/atmel_tclib.c
> F: drivers/clocksource/tcb_clksrc.c
>
> -ATMEL TSADCC DRIVER
> -M: Josh Wu <josh.wu@xxxxxxxxx>
> -L: linux-input@xxxxxxxxxxxxxxx
> -S: Supported
> -F: drivers/input/touchscreen/atmel_tsadcc.c
> -
> ATMEL USBA UDC DRIVER
> M: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>
> L: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx (moderated for non-subscribers)
> diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> index 07e9e82029d1..4090f69e78af 100644
> --- a/drivers/input/touchscreen/Kconfig
> +++ b/drivers/input/touchscreen/Kconfig
> @@ -559,18 +559,6 @@ config TOUCHSCREEN_TI_AM335X_TSC
> To compile this driver as a module, choose M here: the
> module will be called ti_am335x_tsc.
>
> -config TOUCHSCREEN_ATMEL_TSADCC
> - tristate "Atmel Touchscreen Interface"
> - depends on ARCH_AT91
> - help
> - Say Y here if you have a 4-wire touchscreen connected to the
> - ADC Controller on your Atmel SoC.
> -
> - If unsure, say N.
> -
> - To compile this driver as a module, choose M here: the
> - module will be called atmel_tsadcc.
> -
> config TOUCHSCREEN_UCB1400
> tristate "Philips UCB1400 touchscreen"
> depends on AC97_BUS
> diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
> index 62801f213346..f326a8290593 100644
> --- a/drivers/input/touchscreen/Makefile
> +++ b/drivers/input/touchscreen/Makefile
> @@ -13,7 +13,6 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879_I2C) += ad7879-i2c.o
> obj-$(CONFIG_TOUCHSCREEN_AD7879_SPI) += ad7879-spi.o
> obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
> obj-$(CONFIG_TOUCHSCREEN_ATMEL_MXT) += atmel_mxt_ts.o
> -obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o
> obj-$(CONFIG_TOUCHSCREEN_AUO_PIXCIR) += auo-pixcir-ts.o
> obj-$(CONFIG_TOUCHSCREEN_BU21013) += bu21013_ts.o
> obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110) += cy8ctmg110_ts.o
> diff --git a/drivers/input/touchscreen/atmel_tsadcc.c b/drivers/input/touchscreen/atmel_tsadcc.c
> deleted file mode 100644
> index a7c9d6967d1e..000000000000
> --- a/drivers/input/touchscreen/atmel_tsadcc.c
> +++ /dev/null
> @@ -1,358 +0,0 @@
> -/*
> - * Atmel Touch Screen Driver
> - *
> - * Copyright (c) 2008 ATMEL
> - * Copyright (c) 2008 Dan Liang
> - * Copyright (c) 2008 TimeSys Corporation
> - * Copyright (c) 2008 Justin Waters
> - *
> - * Based on touchscreen code from Atmel Corporation.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 as
> - * published by the Free Software Foundation.
> - */
> -#include <linux/err.h>
> -#include <linux/kernel.h>
> -#include <linux/module.h>
> -#include <linux/input.h>
> -#include <linux/slab.h>
> -#include <linux/interrupt.h>
> -#include <linux/clk.h>
> -#include <linux/platform_device.h>
> -#include <linux/io.h>
> -#include <linux/platform_data/atmel.h>
> -#include <mach/cpu.h>
> -
> -/* Register definitions based on AT91SAM9RL64 preliminary draft datasheet */
> -
> -#define ATMEL_TSADCC_CR 0x00 /* Control register */
> -#define ATMEL_TSADCC_SWRST (1 << 0) /* Software Reset*/
> -#define ATMEL_TSADCC_START (1 << 1) /* Start conversion */
> -
> -#define ATMEL_TSADCC_MR 0x04 /* Mode register */
> -#define ATMEL_TSADCC_TSAMOD (3 << 0) /* ADC mode */
> -#define ATMEL_TSADCC_TSAMOD_ADC_ONLY_MODE (0x0) /* ADC Mode */
> -#define ATMEL_TSADCC_TSAMOD_TS_ONLY_MODE (0x1) /* Touch Screen Only Mode */
> -#define ATMEL_TSADCC_LOWRES (1 << 4) /* Resolution selection */
> -#define ATMEL_TSADCC_SLEEP (1 << 5) /* Sleep mode */
> -#define ATMEL_TSADCC_PENDET (1 << 6) /* Pen Detect selection */
> -#define ATMEL_TSADCC_PRES (1 << 7) /* Pressure Measurement Selection */
> -#define ATMEL_TSADCC_PRESCAL (0x3f << 8) /* Prescalar Rate Selection */
> -#define ATMEL_TSADCC_EPRESCAL (0xff << 8) /* Prescalar Rate Selection (Extended) */
> -#define ATMEL_TSADCC_STARTUP (0x7f << 16) /* Start Up time */
> -#define ATMEL_TSADCC_SHTIM (0xf << 24) /* Sample & Hold time */
> -#define ATMEL_TSADCC_PENDBC (0xf << 28) /* Pen Detect debouncing time */
> -
> -#define ATMEL_TSADCC_TRGR 0x08 /* Trigger register */
> -#define ATMEL_TSADCC_TRGMOD (7 << 0) /* Trigger mode */
> -#define ATMEL_TSADCC_TRGMOD_NONE (0 << 0)
> -#define ATMEL_TSADCC_TRGMOD_EXT_RISING (1 << 0)
> -#define ATMEL_TSADCC_TRGMOD_EXT_FALLING (2 << 0)
> -#define ATMEL_TSADCC_TRGMOD_EXT_ANY (3 << 0)
> -#define ATMEL_TSADCC_TRGMOD_PENDET (4 << 0)
> -#define ATMEL_TSADCC_TRGMOD_PERIOD (5 << 0)
> -#define ATMEL_TSADCC_TRGMOD_CONTINUOUS (6 << 0)
> -#define ATMEL_TSADCC_TRGPER (0xffff << 16) /* Trigger period */
> -
> -#define ATMEL_TSADCC_TSR 0x0C /* Touch Screen register */
> -#define ATMEL_TSADCC_TSFREQ (0xf << 0) /* TS Frequency in Interleaved mode */
> -#define ATMEL_TSADCC_TSSHTIM (0xf << 24) /* Sample & Hold time */
> -
> -#define ATMEL_TSADCC_CHER 0x10 /* Channel Enable register */
> -#define ATMEL_TSADCC_CHDR 0x14 /* Channel Disable register */
> -#define ATMEL_TSADCC_CHSR 0x18 /* Channel Status register */
> -#define ATMEL_TSADCC_CH(n) (1 << (n)) /* Channel number */
> -
> -#define ATMEL_TSADCC_SR 0x1C /* Status register */
> -#define ATMEL_TSADCC_EOC(n) (1 << ((n)+0)) /* End of conversion for channel N */
> -#define ATMEL_TSADCC_OVRE(n) (1 << ((n)+8)) /* Overrun error for channel N */
> -#define ATMEL_TSADCC_DRDY (1 << 16) /* Data Ready */
> -#define ATMEL_TSADCC_GOVRE (1 << 17) /* General Overrun Error */
> -#define ATMEL_TSADCC_ENDRX (1 << 18) /* End of RX Buffer */
> -#define ATMEL_TSADCC_RXBUFF (1 << 19) /* TX Buffer full */
> -#define ATMEL_TSADCC_PENCNT (1 << 20) /* Pen contact */
> -#define ATMEL_TSADCC_NOCNT (1 << 21) /* No contact */
> -
> -#define ATMEL_TSADCC_LCDR 0x20 /* Last Converted Data register */
> -#define ATMEL_TSADCC_DATA (0x3ff << 0) /* Channel data */
> -
> -#define ATMEL_TSADCC_IER 0x24 /* Interrupt Enable register */
> -#define ATMEL_TSADCC_IDR 0x28 /* Interrupt Disable register */
> -#define ATMEL_TSADCC_IMR 0x2C /* Interrupt Mask register */
> -#define ATMEL_TSADCC_CDR0 0x30 /* Channel Data 0 */
> -#define ATMEL_TSADCC_CDR1 0x34 /* Channel Data 1 */
> -#define ATMEL_TSADCC_CDR2 0x38 /* Channel Data 2 */
> -#define ATMEL_TSADCC_CDR3 0x3C /* Channel Data 3 */
> -#define ATMEL_TSADCC_CDR4 0x40 /* Channel Data 4 */
> -#define ATMEL_TSADCC_CDR5 0x44 /* Channel Data 5 */
> -
> -#define ATMEL_TSADCC_XPOS 0x50
> -#define ATMEL_TSADCC_Z1DAT 0x54
> -#define ATMEL_TSADCC_Z2DAT 0x58
> -
> -#define PRESCALER_VAL(x) ((x) >> 8)
> -
> -#define ADC_DEFAULT_CLOCK 100000
> -
> -struct atmel_tsadcc {
> - struct input_dev *input;
> - char phys[32];
> - struct clk *clk;
> - int irq;
> - unsigned int prev_absx;
> - unsigned int prev_absy;
> - unsigned char bufferedmeasure;
> -};
> -
> -static void __iomem *tsc_base;
> -
> -#define atmel_tsadcc_read(reg) __raw_readl(tsc_base + (reg))
> -#define atmel_tsadcc_write(reg, val) __raw_writel((val), tsc_base + (reg))
> -
> -static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)
> -{
> - struct atmel_tsadcc *ts_dev = (struct atmel_tsadcc *)dev;
> - struct input_dev *input_dev = ts_dev->input;
> -
> - unsigned int status;
> - unsigned int reg;
> -
> - status = atmel_tsadcc_read(ATMEL_TSADCC_SR);
> - status &= atmel_tsadcc_read(ATMEL_TSADCC_IMR);
> -
> - if (status & ATMEL_TSADCC_NOCNT) {
> - /* Contact lost */
> - reg = atmel_tsadcc_read(ATMEL_TSADCC_MR) | ATMEL_TSADCC_PENDBC;
> -
> - atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
> - atmel_tsadcc_write(ATMEL_TSADCC_TRGR, ATMEL_TSADCC_TRGMOD_NONE);
> - atmel_tsadcc_write(ATMEL_TSADCC_IDR,
> - ATMEL_TSADCC_EOC(3) | ATMEL_TSADCC_NOCNT);
> - atmel_tsadcc_write(ATMEL_TSADCC_IER, ATMEL_TSADCC_PENCNT);
> -
> - input_report_key(input_dev, BTN_TOUCH, 0);
> - ts_dev->bufferedmeasure = 0;
> - input_sync(input_dev);
> -
> - } else if (status & ATMEL_TSADCC_PENCNT) {
> - /* Pen detected */
> - reg = atmel_tsadcc_read(ATMEL_TSADCC_MR);
> - reg &= ~ATMEL_TSADCC_PENDBC;
> -
> - atmel_tsadcc_write(ATMEL_TSADCC_IDR, ATMEL_TSADCC_PENCNT);
> - atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
> - atmel_tsadcc_write(ATMEL_TSADCC_IER,
> - ATMEL_TSADCC_EOC(3) | ATMEL_TSADCC_NOCNT);
> - atmel_tsadcc_write(ATMEL_TSADCC_TRGR,
> - ATMEL_TSADCC_TRGMOD_PERIOD | (0x0FFF << 16));
> -
> - } else if (status & ATMEL_TSADCC_EOC(3)) {
> - /* Conversion finished */
> -
> - if (ts_dev->bufferedmeasure) {
> - /* Last measurement is always discarded, since it can
> - * be erroneous.
> - * Always report previous measurement */
> - input_report_abs(input_dev, ABS_X, ts_dev->prev_absx);
> - input_report_abs(input_dev, ABS_Y, ts_dev->prev_absy);
> - input_report_key(input_dev, BTN_TOUCH, 1);
> - input_sync(input_dev);
> - } else
> - ts_dev->bufferedmeasure = 1;
> -
> - /* Now make new measurement */
> - ts_dev->prev_absx = atmel_tsadcc_read(ATMEL_TSADCC_CDR3) << 10;
> - ts_dev->prev_absx /= atmel_tsadcc_read(ATMEL_TSADCC_CDR2);
> -
> - ts_dev->prev_absy = atmel_tsadcc_read(ATMEL_TSADCC_CDR1) << 10;
> - ts_dev->prev_absy /= atmel_tsadcc_read(ATMEL_TSADCC_CDR0);
> - }
> -
> - return IRQ_HANDLED;
> -}
> -
> -/*
> - * The functions for inserting/removing us as a module.
> - */
> -
> -static int atmel_tsadcc_probe(struct platform_device *pdev)
> -{
> - struct atmel_tsadcc *ts_dev;
> - struct input_dev *input_dev;
> - struct resource *res;
> - struct at91_tsadcc_data *pdata = dev_get_platdata(&pdev->dev);
> - int err;
> - unsigned int prsc;
> - unsigned int reg;
> -
> - if (!pdata)
> - return -EINVAL;
> -
> - res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> - if (!res) {
> - dev_err(&pdev->dev, "no mmio resource defined.\n");
> - return -ENXIO;
> - }
> -
> - /* Allocate memory for device */
> - ts_dev = kzalloc(sizeof(struct atmel_tsadcc), GFP_KERNEL);
> - if (!ts_dev) {
> - dev_err(&pdev->dev, "failed to allocate memory.\n");
> - return -ENOMEM;
> - }
> - platform_set_drvdata(pdev, ts_dev);
> -
> - input_dev = input_allocate_device();
> - if (!input_dev) {
> - dev_err(&pdev->dev, "failed to allocate input device.\n");
> - err = -EBUSY;
> - goto err_free_mem;
> - }
> -
> - ts_dev->irq = platform_get_irq(pdev, 0);
> - if (ts_dev->irq < 0) {
> - dev_err(&pdev->dev, "no irq ID is designated.\n");
> - err = -ENODEV;
> - goto err_free_dev;
> - }
> -
> - if (!request_mem_region(res->start, resource_size(res),
> - "atmel tsadcc regs")) {
> - dev_err(&pdev->dev, "resources is unavailable.\n");
> - err = -EBUSY;
> - goto err_free_dev;
> - }
> -
> - tsc_base = ioremap(res->start, resource_size(res));
> - if (!tsc_base) {
> - dev_err(&pdev->dev, "failed to map registers.\n");
> - err = -ENOMEM;
> - goto err_release_mem;
> - }
> -
> - err = request_irq(ts_dev->irq, atmel_tsadcc_interrupt, 0,
> - pdev->dev.driver->name, ts_dev);
> - if (err) {
> - dev_err(&pdev->dev, "failed to allocate irq.\n");
> - goto err_unmap_regs;
> - }
> -
> - ts_dev->clk = clk_get(&pdev->dev, "tsc_clk");
> - if (IS_ERR(ts_dev->clk)) {
> - dev_err(&pdev->dev, "failed to get ts_clk\n");
> - err = PTR_ERR(ts_dev->clk);
> - goto err_free_irq;
> - }
> -
> - ts_dev->input = input_dev;
> - ts_dev->bufferedmeasure = 0;
> -
> - snprintf(ts_dev->phys, sizeof(ts_dev->phys),
> - "%s/input0", dev_name(&pdev->dev));
> -
> - input_dev->name = "atmel touch screen controller";
> - input_dev->phys = ts_dev->phys;
> - input_dev->dev.parent = &pdev->dev;
> -
> - __set_bit(EV_ABS, input_dev->evbit);
> - input_set_abs_params(input_dev, ABS_X, 0, 0x3FF, 0, 0);
> - input_set_abs_params(input_dev, ABS_Y, 0, 0x3FF, 0, 0);
> -
> - input_set_capability(input_dev, EV_KEY, BTN_TOUCH);
> -
> - /* clk_enable() always returns 0, no need to check it */
> - clk_enable(ts_dev->clk);
> -
> - prsc = clk_get_rate(ts_dev->clk);
> - dev_info(&pdev->dev, "Master clock is set at: %d Hz\n", prsc);
> -
> - if (!pdata->adc_clock)
> - pdata->adc_clock = ADC_DEFAULT_CLOCK;
> -
> - prsc = (prsc / (2 * pdata->adc_clock)) - 1;
> -
> - /* saturate if this value is too high */
> - if (cpu_is_at91sam9rl()) {
> - if (prsc > PRESCALER_VAL(ATMEL_TSADCC_PRESCAL))
> - prsc = PRESCALER_VAL(ATMEL_TSADCC_PRESCAL);
> - } else {
> - if (prsc > PRESCALER_VAL(ATMEL_TSADCC_EPRESCAL))
> - prsc = PRESCALER_VAL(ATMEL_TSADCC_EPRESCAL);
> - }
> -
> - dev_info(&pdev->dev, "Prescaler is set at: %d\n", prsc);
> -
> - reg = ATMEL_TSADCC_TSAMOD_TS_ONLY_MODE |
> - ((0x00 << 5) & ATMEL_TSADCC_SLEEP) | /* Normal Mode */
> - ((0x01 << 6) & ATMEL_TSADCC_PENDET) | /* Enable Pen Detect */
> - (prsc << 8) |
> - ((0x26 << 16) & ATMEL_TSADCC_STARTUP) |
> - ((pdata->pendet_debounce << 28) & ATMEL_TSADCC_PENDBC);
> -
> - atmel_tsadcc_write(ATMEL_TSADCC_CR, ATMEL_TSADCC_SWRST);
> - atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
> - atmel_tsadcc_write(ATMEL_TSADCC_TRGR, ATMEL_TSADCC_TRGMOD_NONE);
> - atmel_tsadcc_write(ATMEL_TSADCC_TSR,
> - (pdata->ts_sample_hold_time << 24) & ATMEL_TSADCC_TSSHTIM);
> -
> - atmel_tsadcc_read(ATMEL_TSADCC_SR);
> - atmel_tsadcc_write(ATMEL_TSADCC_IER, ATMEL_TSADCC_PENCNT);
> -
> - /* All went ok, so register to the input system */
> - err = input_register_device(input_dev);
> - if (err)
> - goto err_fail;
> -
> - return 0;
> -
> -err_fail:
> - clk_disable(ts_dev->clk);
> - clk_put(ts_dev->clk);
> -err_free_irq:
> - free_irq(ts_dev->irq, ts_dev);
> -err_unmap_regs:
> - iounmap(tsc_base);
> -err_release_mem:
> - release_mem_region(res->start, resource_size(res));
> -err_free_dev:
> - input_free_device(input_dev);
> -err_free_mem:
> - kfree(ts_dev);
> - return err;
> -}
> -
> -static int atmel_tsadcc_remove(struct platform_device *pdev)
> -{
> - struct atmel_tsadcc *ts_dev = platform_get_drvdata(pdev);
> - struct resource *res;
> -
> - free_irq(ts_dev->irq, ts_dev);
> -
> - input_unregister_device(ts_dev->input);
> -
> - res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> - iounmap(tsc_base);
> - release_mem_region(res->start, resource_size(res));
> -
> - clk_disable(ts_dev->clk);
> - clk_put(ts_dev->clk);
> -
> - kfree(ts_dev);
> -
> - return 0;
> -}
> -
> -static struct platform_driver atmel_tsadcc_driver = {
> - .probe = atmel_tsadcc_probe,
> - .remove = atmel_tsadcc_remove,
> - .driver = {
> - .name = "atmel_tsadcc",
> - },
> -};
> -module_platform_driver(atmel_tsadcc_driver);
> -
> -MODULE_LICENSE("GPL");
> -MODULE_DESCRIPTION("Atmel TouchScreen Driver");
> -MODULE_AUTHOR("Dan Liang <dan.liang@xxxxxxxxx>");
> -
> --
> 1.8.3.2
>
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
