On 10/08/13 04:48, Josh Wu wrote:
> AT91 ADC hardware integrate touch screen support. So this patch add touch
> screen support for at91 adc iio driver.
> To enable touch screen support in adc, you need to add the dt parameters:
> 1. which type of touch are used? (4 or 5 wires), sample period time.
> 2. correct pressure detect threshold value.
>
> In the meantime, since touch screen will use a interal period trigger of adc,
> so it is conflict to other hardware triggers. Driver will disable the hardware
> trigger support if touch screen is enabled.
>
> This driver has been tested in AT91SAM9X5-EK and SAMA5D3x-EK.
>
> Signed-off-by: Josh Wu <josh.wu@xxxxxxxxx>
> Cc: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx>
> CC: devicetree@xxxxxxxxxxxxxxx
Hi Josh. I am not going to take this for now both because I want to have
a close read of it when I have more time and because I want input from
Dmitry on this one.
Thanks,
Jonathan
> ---
> .../devicetree/bindings/arm/atmel-adc.txt | 7 +
> arch/arm/mach-at91/include/mach/at91_adc.h | 34 ++
> drivers/iio/adc/at91_adc.c | 388 ++++++++++++++++++--
> 3 files changed, 405 insertions(+), 24 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/arm/atmel-adc.txt
> index 0e65e01..d106146 100644
> --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt
> +++ b/Documentation/devicetree/bindings/arm/atmel-adc.txt
> @@ -23,6 +23,13 @@ Optional properties:
> resolution will be used.
> - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
> - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
> + - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
> + value is set, then adc driver will enable touch screen
> + support.
> + NOTE: when adc touch screen enabled, the adc hardware trigger will be
> + disabled. Since touch screen will occupied the trigger register.
> + - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
> + make touch detect more precision.
>
> Optional trigger Nodes:
> - Required properties:
> diff --git a/arch/arm/mach-at91/include/mach/at91_adc.h b/arch/arm/mach-at91/include/mach/at91_adc.h
> index 048a57f..c287307 100644
> --- a/arch/arm/mach-at91/include/mach/at91_adc.h
> +++ b/arch/arm/mach-at91/include/mach/at91_adc.h
> @@ -60,14 +60,48 @@
> #define AT91_ADC_IER 0x24 /* Interrupt Enable Register */
> #define AT91_ADC_IDR 0x28 /* Interrupt Disable Register */
> #define AT91_ADC_IMR 0x2C /* Interrupt Mask Register */
> +#define AT91_ADC_IER_PEN (1 << 29)
> +#define AT91_ADC_IER_NOPEN (1 << 30)
> +#define AT91_ADC_IER_XRDY (1 << 20)
> +#define AT91_ADC_IER_YRDY (1 << 21)
> +#define AT91_ADC_IER_PRDY (1 << 22)
> +#define AT91_ADC_ISR_PENS (1 << 31)
>
> #define AT91_ADC_CHR(n) (0x30 + ((n) * 4)) /* Channel Data Register N */
> #define AT91_ADC_DATA (0x3ff)
>
> #define AT91_ADC_CDR0_9X5 (0x50) /* Channel Data Register 0 for 9X5 */
>
> +#define AT91_ADC_ACR 0x94 /* Analog Control Register */
> +#define AT91_ADC_ACR_PENDETSENS (0x3 << 0) /* pull-up resistor */
> +
> +#define AT91_ADC_TSMR 0xB0
> +#define AT91_ADC_TSMR_TSMODE (3 << 0) /* Touch Screen Mode */
> +#define AT91_ADC_TSMR_TSMODE_NONE (0 << 0)
> +#define AT91_ADC_TSMR_TSMODE_4WIRE_NO_PRESS (1 << 0)
> +#define AT91_ADC_TSMR_TSMODE_4WIRE_PRESS (2 << 0)
> +#define AT91_ADC_TSMR_TSMODE_5WIRE (3 << 0)
> +#define AT91_ADC_TSMR_TSAV (3 << 4) /* Averages samples */
> +#define AT91_ADC_TSMR_TSAV_(x) ((x) << 4)
> +#define AT91_ADC_TSMR_SCTIM (0x0f << 16) /* Switch closure time */
> +#define AT91_ADC_TSMR_PENDBC (0x0f << 28) /* Pen Debounce time */
> +#define AT91_ADC_TSMR_PENDBC_(x) ((x) << 28)
> +#define AT91_ADC_TSMR_NOTSDMA (1 << 22) /* No Touchscreen DMA */
> +#define AT91_ADC_TSMR_PENDET_DIS (0 << 24) /* Pen contact detection disable */
> +#define AT91_ADC_TSMR_PENDET_ENA (1 << 24) /* Pen contact detection enable */
> +
> +#define AT91_ADC_TSXPOSR 0xB4
> +#define AT91_ADC_TSYPOSR 0xB8
> +#define AT91_ADC_TSPRESSR 0xBC
> +
> #define AT91_ADC_TRGR_9260 AT91_ADC_MR
> #define AT91_ADC_TRGR_9G45 0x08
> #define AT91_ADC_TRGR_9X5 0xC0
>
> +/* Trigger Register bit field */
> +#define AT91_ADC_TRGR_TRGPER (0xffff << 16)
> +#define AT91_ADC_TRGR_TRGPER_(x) ((x) << 16)
> +#define AT91_ADC_TRGR_TRGMOD (0x7 << 0)
> +#define AT91_ADC_TRGR_MOD_PERIOD_TRIG (5 << 0)
> +
> #endif
> diff --git a/drivers/iio/adc/at91_adc.c b/drivers/iio/adc/at91_adc.c
> index 22cf61d2..68ddd7f 100644
> --- a/drivers/iio/adc/at91_adc.c
> +++ b/drivers/iio/adc/at91_adc.c
> @@ -11,6 +11,7 @@
> #include <linux/clk.h>
> #include <linux/err.h>
> #include <linux/io.h>
> +#include <linux/input.h>
> #include <linux/interrupt.h>
> #include <linux/jiffies.h>
> #include <linux/kernel.h>
> @@ -39,7 +40,23 @@
> #define at91_adc_writel(st, reg, val) \
> (writel_relaxed(val, st->reg_base + reg))
>
> +#define DRIVER_NAME "at91_adc"
> +#define MAX_POS_BITS 12
> +
> +#define TOUCH_SAMPLE_PERIOD_US 2000 /* 2ms */
> +#define TOUCH_PEN_DETECT_DEBOUNCE_US 200
> +
> struct at91_adc_caps {
> + bool has_ts; /* Support touch screen */
> + bool has_tsmr; /* only at91sam9x5, sama5d3 have TSMR reg */
> + /*
> + * Numbers of sampling data will be averaged. Can be 0~3.
> + * Hardware can average (2 ^ ts_filter_average) sample data.
> + */
> + u8 ts_filter_average;
> + /* Pen Detection input pull-up resistor, can be 0~3 */
> + u8 ts_pen_detect_sensitivity;
> +
> /* startup time calculate function */
> u32 (*calc_startup_ticks)(u8 startup_time, u32 adc_clk_khz);
>
> @@ -47,6 +64,12 @@ struct at91_adc_caps {
> struct at91_adc_reg_desc registers;
> };
>
> +enum atmel_adc_ts_type {
> + ATMEL_ADC_TOUCHSCREEN_NONE = 0,
> + ATMEL_ADC_TOUCHSCREEN_4WIRE = 4,
> + ATMEL_ADC_TOUCHSCREEN_5WIRE = 5,
> +};
> +
> struct at91_adc_state {
> struct clk *adc_clk;
> u16 *buffer;
> @@ -71,6 +94,26 @@ struct at91_adc_state {
> bool low_res; /* the resolution corresponds to the lowest one */
> wait_queue_head_t wq_data_avail;
> struct at91_adc_caps *caps;
> +
> + /*
> + * Following ADC channels are shared by touchscreen:
> + *
> + * CH0 -- Touch screen XP/UL
> + * CH1 -- Touch screen XM/UR
> + * CH2 -- Touch screen YP/LL
> + * CH3 -- Touch screen YM/Sense
> + * CH4 -- Touch screen LR(5-wire only)
> + *
> + * The bitfields below represents the reserved channel in the
> + * touchscreen mode.
> + */
> +#define CHAN_MASK_TOUCHSCREEN_4WIRE (0xf << 0)
> +#define CHAN_MASK_TOUCHSCREEN_5WIRE (0x1f << 0)
> + enum atmel_adc_ts_type touchscreen_type;
> + struct input_dev *ts_input;
> +
> + u16 ts_sample_period_val;
> + u32 ts_pressure_threshold;
> };
>
> static irqreturn_t at91_adc_trigger_handler(int irq, void *p)
> @@ -105,14 +148,10 @@ static irqreturn_t at91_adc_trigger_handler(int irq, void *p)
> return IRQ_HANDLED;
> }
>
> -static irqreturn_t at91_adc_eoc_trigger(int irq, void *private)
> +/* Handler for classic adc channel eoc trigger */
> +void handle_adc_eoc_trigger(int irq, struct iio_dev *idev)
> {
> - struct iio_dev *idev = private;
> struct at91_adc_state *st = iio_priv(idev);
> - u32 status = at91_adc_readl(st, st->registers->status_register);
> -
> - if (!(status & st->registers->drdy_mask))
> - return IRQ_HANDLED;
>
> if (iio_buffer_enabled(idev)) {
> disable_irq_nosync(irq);
> @@ -122,6 +161,115 @@ static irqreturn_t at91_adc_eoc_trigger(int irq, void *private)
> st->done = true;
> wake_up_interruptible(&st->wq_data_avail);
> }
> +}
> +
> +static int at91_ts_sample(struct at91_adc_state *st)
> +{
> + unsigned int xscale, yscale, reg, z1, z2;
> + unsigned int x, y, pres, xpos, ypos;
> + unsigned int rxp = 1;
> + unsigned int factor = 1000;
> + struct iio_dev *idev = iio_priv_to_dev(st);
> +
> + unsigned int xyz_mask_bits = st->res;
> + unsigned int xyz_mask = (1 << xyz_mask_bits) - 1;
> +
> + /* calculate position */
> + /* x position = (x / xscale) * max, max = 2^MAX_POS_BITS - 1 */
> + reg = at91_adc_readl(st, AT91_ADC_TSXPOSR);
> + xpos = reg & xyz_mask;
> + x = (xpos << MAX_POS_BITS) - xpos;
> + xscale = (reg >> 16) & xyz_mask;
> + if (xscale == 0) {
> + dev_err(&idev->dev, "Error: xscale == 0!\n");
> + return -1;
> + }
> + x /= xscale;
> +
> + /* y position = (y / yscale) * max, max = 2^MAX_POS_BITS - 1 */
> + reg = at91_adc_readl(st, AT91_ADC_TSYPOSR);
> + ypos = reg & xyz_mask;
> + y = (ypos << MAX_POS_BITS) - ypos;
> + yscale = (reg >> 16) & xyz_mask;
> + if (yscale == 0) {
> + dev_err(&idev->dev, "Error: yscale == 0!\n");
> + return -1;
> + }
> + y /= yscale;
> +
> + /* calculate the pressure */
> + reg = at91_adc_readl(st, AT91_ADC_TSPRESSR);
> + z1 = reg & xyz_mask;
> + z2 = (reg >> 16) & xyz_mask;
> +
> + if (z1 != 0)
> + pres = rxp * (x * factor / 1024) * (z2 * factor / z1 - factor)
> + / factor;
> + else
> + pres = st->ts_pressure_threshold; /* no pen contacted */
> +
> + dev_dbg(&idev->dev, "xpos = %d, xscale = %d, ypos = %d, yscale = %d, z1 = %d, z2 = %d, press = %d\n",
> + xpos, xscale, ypos, yscale, z1, z2, pres);
> +
> + if (pres < st->ts_pressure_threshold) {
> + dev_dbg(&idev->dev, "x = %d, y = %d, pressure = %d\n",
> + x, y, pres / factor);
> + input_report_abs(st->ts_input, ABS_X, x);
> + input_report_abs(st->ts_input, ABS_Y, y);
> + input_report_abs(st->ts_input, ABS_PRESSURE, pres);
> + input_report_key(st->ts_input, BTN_TOUCH, 1);
> + input_sync(st->ts_input);
> + } else {
> + dev_dbg(&idev->dev, "pressure too low: not reporting\n");
> + }
> +
> + return 0;
> +}
> +
> +static irqreturn_t at91_adc_interrupt(int irq, void *private)
> +{
> + struct iio_dev *idev = private;
> + struct at91_adc_state *st = iio_priv(idev);
> + u32 status = at91_adc_readl(st, st->registers->status_register);
> + const uint32_t ts_data_irq_mask =
> + AT91_ADC_IER_XRDY |
> + AT91_ADC_IER_YRDY |
> + AT91_ADC_IER_PRDY;
> +
> + if (status & st->registers->drdy_mask)
> + handle_adc_eoc_trigger(irq, idev);
> +
> + if (status & AT91_ADC_IER_PEN) {
> + at91_adc_writel(st, AT91_ADC_IDR, AT91_ADC_IER_PEN);
> + at91_adc_writel(st, AT91_ADC_IER, AT91_ADC_IER_NOPEN |
> + ts_data_irq_mask);
> + /* Set up period trigger for sampling */
> + at91_adc_writel(st, st->registers->trigger_register,
> + AT91_ADC_TRGR_MOD_PERIOD_TRIG |
> + AT91_ADC_TRGR_TRGPER_(st->ts_sample_period_val));
> + } else if (status & AT91_ADC_IER_NOPEN) {
> + at91_adc_writel(st, st->registers->trigger_register, 0);
> + at91_adc_writel(st, AT91_ADC_IDR, AT91_ADC_IER_NOPEN |
> + ts_data_irq_mask);
> + at91_adc_writel(st, AT91_ADC_IER, AT91_ADC_IER_PEN);
> +
> + input_report_key(st->ts_input, BTN_TOUCH, 0);
> + input_sync(st->ts_input);
> + } else if ((status & ts_data_irq_mask) == ts_data_irq_mask) {
> + /* Now all touchscreen data is ready */
> +
> + if (status & AT91_ADC_ISR_PENS) {
> + /* validate data by pen contact */
> + at91_ts_sample(st);
> + } else {
> + /* triggered by event that is no pen contact, just read
> + * them to clean the interrupt and discard all.
> + */
> + at91_adc_readl(st, AT91_ADC_TSXPOSR);
> + at91_adc_readl(st, AT91_ADC_TSYPOSR);
> + at91_adc_readl(st, AT91_ADC_TSPRESSR);
> + }
> + }
>
> return IRQ_HANDLED;
> }
> @@ -131,6 +279,16 @@ static int at91_adc_channel_init(struct iio_dev *idev)
> struct at91_adc_state *st = iio_priv(idev);
> struct iio_chan_spec *chan_array, *timestamp;
> int bit, idx = 0;
> + unsigned long rsvd_mask = 0;
> +
> + /* If touchscreen is enable, then reserve the adc channels */
> + if (st->touchscreen_type == ATMEL_ADC_TOUCHSCREEN_4WIRE)
> + rsvd_mask = CHAN_MASK_TOUCHSCREEN_4WIRE;
> + else if (st->touchscreen_type == ATMEL_ADC_TOUCHSCREEN_5WIRE)
> + rsvd_mask = CHAN_MASK_TOUCHSCREEN_5WIRE;
> +
> + /* set up the channel mask to reserve touchscreen channels */
> + st->channels_mask &= ~rsvd_mask;
>
> idev->num_channels = bitmap_weight(&st->channels_mask,
> st->num_channels) + 1;
> @@ -479,6 +637,39 @@ static u32 calc_startup_ticks_9x5(u8 startup_time, u32 adc_clk_khz)
>
> static const struct of_device_id at91_adc_dt_ids[];
>
> +static int at91_adc_probe_dt_ts(struct device_node *node,
> + struct at91_adc_state *st, struct device *dev)
> +{
> + int ret;
> + u32 prop;
> +
> + ret = of_property_read_u32(node, "atmel,adc-ts-wires", &prop);
> + if (ret) {
> + dev_info(dev, "ADC Touch screen is disabled.\n");
> + return 0;
> + }
> +
> + switch (prop) {
> + case 4:
> + case 5:
> + st->touchscreen_type = prop;
> + break;
> + default:
> + dev_err(dev, "Unsupported number of touchscreen wires (%d). Should be 4 or 5.\n", prop);
> + return -EINVAL;
> + }
> +
> + prop = 0;
> + of_property_read_u32(node, "atmel,adc-ts-pressure-threshold", &prop);
> + st->ts_pressure_threshold = prop;
> + if (st->ts_pressure_threshold) {
> + return 0;
> + } else {
> + dev_err(dev, "Invalid pressure threshold for the touchscreen\n");
> + return -EINVAL;
> + }
> +}
> +
> static int at91_adc_probe_dt(struct at91_adc_state *st,
> struct platform_device *pdev)
> {
> @@ -560,6 +751,12 @@ static int at91_adc_probe_dt(struct at91_adc_state *st,
> i++;
> }
>
> + /* Check if touchscreen is supported. */
> + if (st->caps->has_ts)
> + return at91_adc_probe_dt_ts(node, st, &idev->dev);
> + else
> + dev_info(&idev->dev, "not support touchscreen in the adc compatible string.\n");
> +
> return 0;
>
> error_ret:
> @@ -591,6 +788,114 @@ static const struct iio_info at91_adc_info = {
> .read_raw = &at91_adc_read_raw,
> };
>
> +/* Touchscreen related functions */
> +static int atmel_ts_open(struct input_dev *dev)
> +{
> + struct at91_adc_state *st = input_get_drvdata(dev);
> +
> + at91_adc_writel(st, AT91_ADC_IER, AT91_ADC_IER_PEN);
> + return 0;
> +}
> +
> +static void atmel_ts_close(struct input_dev *dev)
> +{
> + struct at91_adc_state *st = input_get_drvdata(dev);
> +
> + at91_adc_writel(st, AT91_ADC_IDR, AT91_ADC_IER_PEN);
> +}
> +
> +static int at91_ts_hw_init(struct at91_adc_state *st, u32 adc_clk_khz)
> +{
> + u32 reg = 0, pendbc;
> + int i = 0;
> +
> + if (st->touchscreen_type == ATMEL_ADC_TOUCHSCREEN_4WIRE)
> + reg = AT91_ADC_TSMR_TSMODE_4WIRE_PRESS;
> + else
> + reg = AT91_ADC_TSMR_TSMODE_5WIRE;
> +
> + /* a Pen Detect Debounce Time is necessary for the ADC Touch to avoid
> + * pen detect noise.
> + * The formula is : Pen Detect Debounce Time = (2 ^ pendbc) / ADCClock
> + */
> + pendbc = round_up(TOUCH_PEN_DETECT_DEBOUNCE_US * adc_clk_khz / 1000, 1);
> +
> + while (pendbc >> ++i)
> + ; /* Empty! Find the shift offset */
> + if (abs(pendbc - (1 << i)) < abs(pendbc - (1 << (i - 1))))
> + pendbc = i;
> + else
> + pendbc = i - 1;
> +
> + if (st->caps->has_tsmr) {
> + reg |= AT91_ADC_TSMR_TSAV_(st->caps->ts_filter_average)
> + & AT91_ADC_TSMR_TSAV;
> + reg |= AT91_ADC_TSMR_PENDBC_(pendbc) & AT91_ADC_TSMR_PENDBC;
> + reg |= AT91_ADC_TSMR_NOTSDMA;
> + reg |= AT91_ADC_TSMR_PENDET_ENA;
> + reg |= 0x03 << 8; /* TSFREQ, need bigger than TSAV */
> +
> + at91_adc_writel(st, AT91_ADC_TSMR, reg);
> + } else {
> + /* TODO: for 9g45 which has no TSMR */
> + }
> +
> + /* Change adc internal resistor value for better pen detection,
> + * default value is 100 kOhm.
> + * 0 = 200 kOhm, 1 = 150 kOhm, 2 = 100 kOhm, 3 = 50 kOhm
> + * option only available on ES2 and higher
> + */
> + at91_adc_writel(st, AT91_ADC_ACR, st->caps->ts_pen_detect_sensitivity
> + & AT91_ADC_ACR_PENDETSENS);
> +
> + /* Sample Peroid Time = (TRGPER + 1) / ADCClock */
> + st->ts_sample_period_val = round_up((TOUCH_SAMPLE_PERIOD_US *
> + adc_clk_khz / 1000) - 1, 1);
> +
> + return 0;
> +}
> +
> +static int at91_ts_register(struct at91_adc_state *st,
> + struct platform_device *pdev)
> +{
> + struct input_dev *input;
> + struct iio_dev *idev = iio_priv_to_dev(st);
> + int ret;
> +
> + input = input_allocate_device();
> + if (!input) {
> + dev_err(&idev->dev, "Failed to allocate TS device!\n");
> + return -ENOMEM;
> + }
> +
> + input->name = DRIVER_NAME;
> + input->id.bustype = BUS_HOST;
> + input->dev.parent = &pdev->dev;
> + input->open = atmel_ts_open;
> + input->close = atmel_ts_close;
> +
> + __set_bit(EV_ABS, input->evbit);
> + __set_bit(EV_KEY, input->evbit);
> + __set_bit(BTN_TOUCH, input->keybit);
> + input_set_abs_params(input, ABS_X, 0, (1 << MAX_POS_BITS) - 1, 0, 0);
> + input_set_abs_params(input, ABS_Y, 0, (1 << MAX_POS_BITS) - 1, 0, 0);
> + input_set_abs_params(input, ABS_PRESSURE, 0, 0xffffff, 0, 0);
> +
> + st->ts_input = input;
> + input_set_drvdata(input, st);
> +
> + ret = input_register_device(input);
> + if (ret)
> + input_free_device(st->ts_input);
> +
> + return ret;
> +}
> +
> +static void at91_ts_unregister(struct at91_adc_state *st)
> +{
> + input_unregister_device(st->ts_input);
> +}
> +
> static int at91_adc_probe(struct platform_device *pdev)
> {
> unsigned int prsc, mstrclk, ticks, adc_clk, adc_clk_khz, shtim;
> @@ -642,7 +947,7 @@ static int at91_adc_probe(struct platform_device *pdev)
> at91_adc_writel(st, AT91_ADC_CR, AT91_ADC_SWRST);
> at91_adc_writel(st, AT91_ADC_IDR, 0xFFFFFFFF);
> ret = request_irq(st->irq,
> - at91_adc_eoc_trigger,
> + at91_adc_interrupt,
> 0,
> pdev->dev.driver->name,
> idev);
> @@ -687,6 +992,10 @@ static int at91_adc_probe(struct platform_device *pdev)
> mstrclk = clk_get_rate(st->clk);
> adc_clk = clk_get_rate(st->adc_clk);
> adc_clk_khz = adc_clk / 1000;
> +
> + dev_dbg(&pdev->dev, "Master clock is set as: %d Hz, adc_clk should set as: %d Hz\n",
> + mstrclk, adc_clk);
> +
> prsc = (mstrclk / (2 * adc_clk)) - 1;
>
> if (!st->startup_time) {
> @@ -723,30 +1032,52 @@ static int at91_adc_probe(struct platform_device *pdev)
> init_waitqueue_head(&st->wq_data_avail);
> mutex_init(&st->lock);
>
> - ret = at91_adc_buffer_init(idev);
> - if (ret < 0) {
> - dev_err(&pdev->dev, "Couldn't initialize the buffer.\n");
> - goto error_disable_adc_clk;
> - }
> + /*
> + * Since touch screen will set trigger register as period trigger. So
> + * when touch screen is enabled, then we have to disable hardware
> + * trigger for classic adc.
> + */
> + if (!st->touchscreen_type) {
> + ret = at91_adc_buffer_init(idev);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "Couldn't initialize the buffer.\n");
> + goto error_disable_adc_clk;
> + }
>
> - ret = at91_adc_trigger_init(idev);
> - if (ret < 0) {
> - dev_err(&pdev->dev, "Couldn't setup the triggers.\n");
> - goto error_unregister_buffer;
> + ret = at91_adc_trigger_init(idev);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "Couldn't setup the triggers.\n");
> + at91_adc_buffer_remove(idev);
> + goto error_disable_adc_clk;
> + }
> + } else {
> + if (!st->caps->has_tsmr) {
> + dev_err(&pdev->dev, "We don't support non-TSMR adc\n");
> + goto error_disable_adc_clk;
> + }
> +
> + ret = at91_ts_register(st, pdev);
> + if (ret)
> + goto error_disable_adc_clk;
> +
> + at91_ts_hw_init(st, adc_clk_khz);
> }
>
> ret = iio_device_register(idev);
> if (ret < 0) {
> dev_err(&pdev->dev, "Couldn't register the device.\n");
> - goto error_remove_triggers;
> + goto error_iio_device_register;
> }
>
> return 0;
>
> -error_remove_triggers:
> - at91_adc_trigger_remove(idev);
> -error_unregister_buffer:
> - at91_adc_buffer_remove(idev);
> +error_iio_device_register:
> + if (!st->touchscreen_type) {
> + at91_adc_trigger_remove(idev);
> + at91_adc_buffer_remove(idev);
> + } else {
> + at91_ts_unregister(st);
> + }
> error_disable_adc_clk:
> clk_disable_unprepare(st->adc_clk);
> error_disable_clk:
> @@ -762,8 +1093,12 @@ static int at91_adc_remove(struct platform_device *pdev)
> struct at91_adc_state *st = iio_priv(idev);
>
> iio_device_unregister(idev);
> - at91_adc_trigger_remove(idev);
> - at91_adc_buffer_remove(idev);
> + if (!st->touchscreen_type) {
> + at91_adc_trigger_remove(idev);
> + at91_adc_buffer_remove(idev);
> + } else {
> + at91_ts_unregister(st);
> + }
> clk_disable_unprepare(st->adc_clk);
> clk_disable_unprepare(st->clk);
> free_irq(st->irq, idev);
> @@ -786,6 +1121,7 @@ static struct at91_adc_caps at91sam9260_caps = {
> };
>
> static struct at91_adc_caps at91sam9g45_caps = {
> + .has_ts = true,
> .calc_startup_ticks = calc_startup_ticks_9260, /* same as 9260 */
> .num_channels = 8,
> .registers = {
> @@ -799,6 +1135,10 @@ static struct at91_adc_caps at91sam9g45_caps = {
> };
>
> static struct at91_adc_caps at91sam9x5_caps = {
> + .has_ts = true,
> + .has_tsmr = true,
> + .ts_filter_average = 3,
> + .ts_pen_detect_sensitivity = 2,
> .calc_startup_ticks = calc_startup_ticks_9x5,
> .num_channels = 12,
> .registers = {
> @@ -825,7 +1165,7 @@ static struct platform_driver at91_adc_driver = {
> .probe = at91_adc_probe,
> .remove = at91_adc_remove,
> .driver = {
> - .name = "at91_adc",
> + .name = DRIVER_NAME,
> .of_match_table = of_match_ptr(at91_adc_dt_ids),
> },
> };
>
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
