November 10, 2022 4:06 AM, "Damien Le Moal" <damien.lemoal@xxxxxxxxxxxxxxxxxx> wrote: > This of course does not mean that this is not a bug in the ahci-mvebu > driver. We can try digging into that. First thing to try: enable debug > messages in libata and libahci/ahci-mvebu. See > Documentation/admin-guide/dynamic-debug-howto.rst for that. Then connect > your eSATA box and see what it says. > > -- > Damien Le Moal > Western Digital Research I used: cd /proc/dynamic_debug/ echo -n "file *ata* +pflmt" > control echo -n "file *ahci* +pflmt" > control echo -n "module ahci_mvebu +pflmt" > control echo -n "module libata +pflmt" > control There are no errors running the commands. Check: root@(none):/proc/dynamic_debug# grep libata control include/linux/libata.h:2049 [libata]ata_wait_idle =pmflt "ata%u: abnormal Status 0x%X\n" drivers/ata/libata-sff.c:2107 [libata]ata_sff_drain_fifo =pmflt "ata%u: drained %d bytes to clear DRQ\n" drivers/ata/libata-transport.c:344 [libata]ata_port_classify =pmflt "ata%u: found %s device by sig\n" drivers/ata/libata-eh.c:2747 [libata]ata_eh_reset =pmflt "ata%u.%02u: link status unknown, clearing UNKNOWN to NONE\n" drivers/ata/libata-eh.c:2742 [libata]ata_eh_reset =pmflt "ata%u.%02u: link offline, clearing class %d to NONE\n" drivers/ata/libata-eh.c:2736 [libata]ata_eh_reset =pmflt "ata%u.%02u: link online but device misclassified\n" drivers/ata/libata-eh.c:2542 [libata]ata_eh_reset =pmflt "ata%u: port disabled--ignoring\n" drivers/ata/libata-eh.c:2542 [libata]ata_eh_reset =pmflt "ata%u.%02u: port disabled--ignoring\n" drivers/ata/libata-scsi.c:4244 [libata]ata_scsi_assign_ofnode =pmflt "found matching device node\n" drivers/ata/libata-core.c:3344 [libata]ata_dev_set_mode =pmflt "ata%u.%02u: xfer_shift=%u, xfer_mode=0x%x\n" drivers/ata/libata-core.c:4305 [libata]ata_dev_set_xfermode =pmflt "ata%u.%02u: set features - xfer mode\n" drivers/ata/libata-core.c:2356 [libata]ata_dev_config_trusted =pmflt "ata%u.%02u: Trusted Computing capability qword not valid!\n" drivers/ata/libata-core.c:2274 [libata]ata_dev_config_sense_reporting =pmflt "ata%u.%02u: failed to enable Sense Data Reporting, Emask 0x%x\n" drivers/ata/libata-core.c:2124 [libata]ata_dev_config_ncq_send_recv =pmflt "ata%u.%02u: disabling queued TRIM support\n" drivers/ata/libata-core.c:1363 [libata]ata_dump_id =pmflt "ata%u.%02u: 49==0x%04x 53==0x%04x 63==0x%04x 64==0x%04x 75==0x%04x\n80==0x%04x 81==0x%04x 82==0x%04x 83==0x%04x 84==0x%04x\n88==0x%04x 93==0x%04x\n" drivers/ata/libata-core.c:2596 [libata]ata_dev_configure =pmflt "ata%u.%02u: %s: cfg 49:%04x 82:%04x 83:%04x 84:%04x 85:%04x 86:%04x 87:%04x 88:%04x\n" drivers/ata/libata-core.c:2545 [libata]ata_dev_configure =pmflt "ata%u.%02u: no device\n" drivers/ata/libata-core.c:4391 [libata]ata_dev_init_params =pmflt "ata%u.%02u: init dev params \n" drivers/ata/libata-core.c:1877 [libata]ata_dev_read_id =pmflt "ata%u.%02u: host indicates ignore ATA devices, ignored\n" drivers/ata/libata-core.c:1843 [libata]ata_dev_read_id =pmflt "ata%u.%02u: both IDENTIFYs aborted, assuming NODEV\n" drivers/ata/libata-core.c:1811 [libata]ata_dev_read_id =pmflt "ata%u.%02u: NODEV after polling detection\n" drivers/ata/libata-core.c:1970 [libata]ata_read_log_page =pmflt "ata%u.%02u: read log page - log 0x%x, page 0x%x\n" drivers/ata/libata-core.c:4351 [libata]ata_dev_set_feature =pmflt "ata%u.%02u: set features\n" root@(none):/proc/dynamic_debug# grep ahci control drivers/ata/libahci.c:1313 [libahci]ahci_init_controller =pmflt "HOST_CTL 0x%x\n" drivers/ata/libahci.c:1310 [libahci]ahci_init_controller =pmflt "HOST_CTL 0x%x\n" drivers/ata/libahci.c:1279 [libahci]ahci_port_init =pmflt "PORT_IRQ_STAT 0x%x\n" drivers/ata/libahci.c:1274 [libahci]ahci_port_init =pmflt "PORT_SCR_ERR 0x%x\n" I don't see any ahci_mvebu debug strings. Kernel log: ---- Connect laptop HDD ---- [ 195.229143][ T108] [108] libata:ata_port_classify:344: ata2: found ata device by sig [ 195.409141][ T108] [108] libata:ata_port_classify:344: ata2: found ata device by sig [ 195.417008][ T108] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 195.685415][ T108] [108] libata:ata_dev_configure:2596: ata2.00: ata_dev_configure: cfg 49:2f00 82:346b 83:7d09 84:6123 85:3469 86:bc09 87:6123 88:007f [ 195.699132][ T108] [108] libata:ata_dump_id:1363: ata2.00: 49==0x2f00 53==0x0007 63==0x0407 64==0x0003 75==0x001f [ 195.699132][ T108] 80==0x01f0 81==0x0029 82==0x346b 83==0x7d09 84==0x6123 [ 195.699132][ T108] 88==0x007f 93==0x0000 [ 195.721221][ T108] ata2.00: ATA-8: ST9500325AS, 0001SDM1, max UDMA/133 [ 195.727865][ T108] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32) [ 195.735129][ T108] [108] libata:ata_dev_set_xfermode:4305: ata2.00: set features - xfer mode [ 195.745985][ T108] [108] libata:ata_dev_configure:2596: ata2.00: ata_dev_configure: cfg 49:2f00 82:346b 83:7d09 84:6123 85:3469 86:bc09 87:6123 88:407f [ 195.759699][ T108] [108] libata:ata_dump_id:1363: ata2.00: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f [ 195.759699][ T108] 80==0x01f0 81==0x0029 82==0x346b 83==0x7d09 84==0x6123 [ 195.759699][ T108] 88==0x407f 93==0x0000 [ 195.781791][ T108] [108] libata:ata_dev_set_mode:3344: ata2.00: xfer_shift=12, xfer_mode=0x46 [ 195.790443][ T108] ata2.00: configured for UDMA/133 [ 195.795640][ T87] scsi 1:0:0:0: Direct-Access ATA ST9500325AS SDM1 PQ: 0 ANSI: 5 [ 195.804660][ T87] device: 'target1:0:0': device_add [ 195.809750][ T87] bus: 'scsi': add device target1:0:0 [ 195.815024][ T87] device: '1:0:0:0': device_add [ 195.819805][ T87] bus: 'scsi': add device 1:0:0:0 [ 195.825210][ T87] scsi 1:0:0:0: scheduling asynchronous probe [ 195.831480][ T28] bus: 'scsi': __driver_probe_device: matched device 1:0:0:0 with driver sd [ 195.831688][ T87] device: '1:0:0:0': device_add [ 195.840063][ T28] bus: 'scsi': really_probe: probing driver sd with device 1:0:0:0 [ 195.852567][ T28] sd 1:0:0:0: no default pinctrl state [ 195.857932][ T28] device: '1:0:0:0': device_add [ 195.863018][ T28] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 195.871262][ T28] sd 1:0:0:0: [sdb] Write Protect is off [ 195.876774][ T28] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 195.882593][ T28] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 195.892422][ T28] sd 1:0:0:0: [sdb] Preferred minimum I/O size 512 bytes [ 195.899336][ T28] device: 'sdb': device_add [ 195.905171][ T28] device: '8:16': device_add [ 195.932431][ T28] sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 195.938644][ T28] driver: 'sd': driver_bound: bound to device '1:0:0:0' [ 195.945486][ T28] bus: 'scsi': really_probe: bound device 1:0:0:0 to driver sd [ 195.952927][ T28] sd 1:0:0:0: async probe completed ---- Disconnect HDD ---- [ 243.349142][ T108] ata2: SATA link down (SStatus 0 SControl 300) [ 248.750304][ T108] ata2: SATA link down (SStatus 0 SControl 300) [ 254.110303][ T108] ata2: SATA link down (SStatus 0 SControl 300) [ 254.116424][ T108] ata2.00: disable device [ 254.120641][ T87] ata2.00: detaching (SCSI 1:0:0:0) [ 254.125714][ T87] device: '1:0:0:0': device_unregister [ 254.131477][ T87] bus: 'scsi': remove device 1:0:0:0 [ 254.136793][ T87] device: '8:16': device_unregister [ 254.141898][ T87] device: '8:16': device_create_release [ 254.199147][ T87] sd 1:0:0:0: [sdb] Synchronizing SCSI cache [ 254.205047][ T87] sd 1:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK [ 254.215099][ T87] sd 1:0:0:0: [sdb] Stopping disk [ 254.220012][ T87] sd 1:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK [ 254.229591][ T87] bus: 'scsi': remove device target1:0:0 ---- Connect Areca DAS ---- [ 385.299142][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 386.979141][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 388.109141][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 389.999141][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 390.879141][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 390.885440][ T108] ata2: EH pending after 5 tries, giving up No more messages appear after this. Not even when I unplug the cable. The laptop HDD that worked before is no longer detected. The port is dead. After hard reset, with the same dynamic_debug setup: ---- Connect Areca DAS ---- [ 548.949140][ T108] ata2: COMRESET failed (errno=-32) [ 548.954221][ T108] ata2: reset failed (errno=-32), retrying in 8 secs [ 559.089139][ T108] ata2: COMRESET failed (errno=-32) [ 559.094212][ T108] ata2: reset failed (errno=-32), retrying in 8 secs [ 569.289139][ T108] ata2: COMRESET failed (errno=-32) [ 569.294211][ T108] ata2: reset failed (errno=-32), retrying in 33 secs [ 604.339139][ T108] ata2: COMRESET failed (errno=-32) [ 604.344212][ T108] ata2: reset failed, giving up [ 606.599139][ T108] ata2: COMRESET failed (errno=-32) [ 606.604211][ T108] ata2: reset failed (errno=-32), retrying in 8 secs [ 615.799142][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 616.999142][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 619.459139][ T108] ata2: COMRESET failed (errno=-32) [ 619.464211][ T108] ata2: reset failed (errno=-32), retrying in 8 secs [ 628.809141][ T108] ata2: SATA link down (SStatus 101 SControl 300) [ 631.059139][ T108] ata2: COMRESET failed (errno=-32) [ 631.064211][ T108] ata2: reset failed (errno=-32), retrying in 8 secs [ 641.579139][ T108] ata2: COMRESET failed (errno=-32) [ 641.584211][ T108] ata2: reset failed (errno=-32), retrying in 8 secs [ 651.779139][ T108] ata2: COMRESET failed (errno=-32) [ 651.784211][ T108] ata2: reset failed (errno=-32), retrying in 33 secs [ 685.399141][ T108] ata2: SATA link down (SStatus 100 SControl 300) [ 685.405439][ T108] ata2: EH pending after 5 tries, giving up After this, the port is dead again. No more messages appear. Notice there is no COMRESET error if I connect the laptop HDD first. Marius Dinu
