>-----Original Message----- >From: Rob Herring [mailto:robh@xxxxxxxxxx] >Sent: Monday, February 19, 2018 8:17 AM >To: Preetham Chandru <pchandru@xxxxxxxxxx> >Cc: thierry.reding@xxxxxxxxx; tj@xxxxxxxxxx; cyndis@xxxxxxxx; >mark.rutland@xxxxxxx; devicetree@xxxxxxxxxxxxxxx; preetham260@xxxxxxxxx; >linux-tegra@xxxxxxxxxxxxxxx; linux-ide@xxxxxxxxxxxxxxx; Venu Byravarasu ><vbyravarasu@xxxxxxxxxx>; Pavan Kunapuli <pkunapuli@xxxxxxxxxx> >Subject: Re: [PATCH V7 1/7] dt-bindings: ahci-tegra: add binding documentation > >On Mon, Feb 12, 2018 at 10:56:40PM +0530, Preetham Chandru Ramchandra >wrote: >> From: Preetham Ramchandra <pchandru@xxxxxxxxxx> >> >> This adds bindings documentation for the AHCI controller on Tegra210 >> >> Signed-off-by: Preetham Chandru R <pchandru@xxxxxxxxxx> >> --- >> v7: >> * For Aux register set drop the Tegra210 since this register >> set also works on Tegra124 >> * rephrase the sentence for cml1 clock >> * change the commit subject to include ahci-tegra >> * drop pll_e since CCF handles it automatically as >> CML1 is a child clock of it. >> v4: >> * changed the commit message >> * changed 'sata-cold' reset to mandatory for t210 and t124 >> * Removed the regulators for T210 since these regulators >> will be enabled in phy driver. >> v3: >> * Add AUX register. >> v2: >> * change cml1, pll_e and phy regulators as optional >> for T210. >> --- >> .../bindings/ata/nvidia,tegra124-ahci.txt | 35 ++++++++++++++-------- >> 1 file changed, 22 insertions(+), 13 deletions(-) >> >> diff --git >> a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> index 66c83c3e8915..0f4520a00716 100644 >> --- a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> +++ b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> @@ -1,20 +1,19 @@ >> -Tegra124 SoC SATA AHCI controller >> +Tegra SoC SATA AHCI controller >> >> Required properties : >> -- compatible : For Tegra124, must contain "nvidia,tegra124-ahci". >> Otherwise, >> - must contain '"nvidia,<chip>-ahci", "nvidia,tegra124-ahci"', where >> <chip> >> - is tegra132. >> -- reg : Should contain 2 entries: >> +- compatible : Must be one of: >> + - Tegra124 : "nvidia,tegra124-ahci" >> + - Tegra210 : "nvidia,tegra210-ahci" > >Are you dropping T132? > Okay will add. >> +- reg : Should contain 3 entries: > >You can't just add more entries to existing compatibles. Does this apply to T124? > Will keep this as per Thierry's suggestion. >> - AHCI register set (SATA BAR5) >> - SATA register set >> + - AUX register set >> - interrupts : Defines the interrupt used by SATA >> - clocks : Must contain an entry for each entry in clock-names. >> See ../clocks/clock-bindings.txt for details. >> - clock-names : Must include the following entries: >> - sata >> - sata-oob >> - - cml1 >> - - pll_e >> - resets : Must contain an entry for each entry in reset-names. >> See ../reset/reset.txt for details. >> - reset-names : Must include the following entries: >> @@ -24,9 +23,19 @@ Required properties : >> - phys : Must contain an entry for each entry in phy-names. >> See ../phy/phy-bindings.txt for details. >> - phy-names : Must include the following entries: >> - - sata-phy : XUSB PADCTL SATA PHY >> -- hvdd-supply : Defines the SATA HVDD regulator >> -- vddio-supply : Defines the SATA VDDIO regulator >> -- avdd-supply : Defines the SATA AVDD regulator >> -- target-5v-supply : Defines the SATA 5V power regulator >> -- target-12v-supply : Defines the SATA 12V power regulator >> + - For T124: >> + - sata-phy : XUSB PADCTL SATA PHY >> + - For T210: >> + - sata-0 > >-names is kind of pointless for a single entry. Differing names is even more >pointless. > Okay, will keep the name same as Tegra124 and move this to optional for T210 alone . Will not try to change the t124 part to optional since it is already present. >> +- For T124: >> + - hvdd-supply : Defines the SATA HVDD regulator >> + - vddio-supply : Defines the SATA VDDIO regulator >> + - avdd-supply : Defines the SATA AVDD regulator >> + - target-5v-supply : Defines the SATA 5V power regulator >> + - target-12v-supply : Defines the SATA 12V power regulator > >No supplies on T210? The last 2 sound like board level supplies to the drive. > This first 3 are related to phy and will be taken care by uphy driver for t210 and the last two are going to the SATA connectors. These two are always on for tegra210. >> + >> +Optional properties: >> +- clock-names : >> + - cml1 : >> + cml1 clock should be defined here if the PHY driver >> + doesn't manage them. If it does, they should not be. >> -- >> 2.7.4 >> -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
