The same code for enabling and disabling SATA clock was found in multiple
places in the driver. Implement functions that enable/disable the SATA clock
and use them in such places instead of duplicating the code.
Signed-off-by: Marek Vasut <marex@xxxxxxx>
Cc: Shawn Guo <shawn.guo@xxxxxxxxxx>
Cc: Richard Zhu <r65037@xxxxxxxxxxxxx>
Cc: Tejun Heo <tj@xxxxxxxxxx>
Cc: Linux-IDE <linux-ide@xxxxxxxxxxxxxxx>
---
drivers/ata/ahci_imx.c | 133 ++++++++++++++++++++++++++++---------------------
1 file changed, 75 insertions(+), 58 deletions(-)
diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
index ae2d73f..c7ee505 100644
--- a/drivers/ata/ahci_imx.c
+++ b/drivers/ata/ahci_imx.c
@@ -47,6 +47,73 @@ static int ahci_imx_hotplug;
module_param_named(hotplug, ahci_imx_hotplug, int, 0644);
MODULE_PARM_DESC(hotplug, "AHCI IMX hot-plug support (0=Don't support, 1=support)");
+static int imx_sata_clock_enable(struct device *dev, bool config)
+{
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+ int ret;
+
+ imxpriv->gpr =
+ syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+ if (IS_ERR(imxpriv->gpr)) {
+ dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
+ return PTR_ERR(imxpriv->gpr);
+ }
+
+ ret = clk_prepare_enable(imxpriv->sata_ref_clk);
+ if (ret < 0) {
+ dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ return ret;
+ }
+
+ /*
+ * set PHY Paremeters, two steps to configure the GPR13,
+ * one write for rest of parameters, mask of first write
+ * is 0x07fffffd, and the other one write for setting
+ * the mpll_clk_en.
+ */
+ if (config) {
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
+ | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK
+ | IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK
+ | IMX6Q_GPR13_SATA_SPD_MODE_MASK
+ | IMX6Q_GPR13_SATA_MPLL_SS_EN
+ | IMX6Q_GPR13_SATA_TX_ATTEN_MASK
+ | IMX6Q_GPR13_SATA_TX_BOOST_MASK
+ | IMX6Q_GPR13_SATA_TX_LVL_MASK
+ | IMX6Q_GPR13_SATA_TX_EDGE_RATE
+ , IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
+ | IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M
+ | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
+ | IMX6Q_GPR13_SATA_SPD_MODE_3P0G
+ | IMX6Q_GPR13_SATA_MPLL_SS_EN
+ | IMX6Q_GPR13_SATA_TX_ATTEN_9_16
+ | IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB
+ | IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
+ }
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+
+ ret = clk_prepare_enable(imxpriv->sata_ref_clk);
+ if (ret < 0) {
+ dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void imx_sata_clock_disable(struct device *dev)
+{
+ struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
+
+ regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
+ IMX6Q_GPR13_SATA_MPLL_CLK_EN,
+ !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
+ clk_disable_unprepare(imxpriv->sata_ref_clk);
+}
+
static void ahci_imx_error_handler(struct ata_port *ap)
{
u32 reg_val;
@@ -72,10 +139,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)
*/
reg_val = readl(mmio + PORT_PHY_CTL);
writel(reg_val | PORT_PHY_CTL_PDDQ_LOC, mmio + PORT_PHY_CTL);
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
+ imx_sata_clock_disable(ap->dev);
imxpriv->no_device = true;
}
@@ -97,44 +161,10 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
unsigned int reg_val;
struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
- imxpriv->gpr =
- syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
- if (IS_ERR(imxpriv->gpr)) {
- dev_err(dev, "failed to find fsl,imx6q-iomux-gpr regmap\n");
- return PTR_ERR(imxpriv->gpr);
- }
-
- ret = clk_prepare_enable(imxpriv->sata_ref_clk);
- if (ret < 0) {
- dev_err(dev, "prepare-enable sata_ref clock err:%d\n", ret);
+ ret = imx_sata_clock_enable(dev, true);
+ if (ret < 0)
return ret;
- }
- /*
- * set PHY Paremeters, two steps to configure the GPR13,
- * one write for rest of parameters, mask of first write
- * is 0x07fffffd, and the other one write for setting
- * the mpll_clk_en.
- */
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
- | IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK
- | IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK
- | IMX6Q_GPR13_SATA_SPD_MODE_MASK
- | IMX6Q_GPR13_SATA_MPLL_SS_EN
- | IMX6Q_GPR13_SATA_TX_ATTEN_MASK
- | IMX6Q_GPR13_SATA_TX_BOOST_MASK
- | IMX6Q_GPR13_SATA_TX_LVL_MASK
- | IMX6Q_GPR13_SATA_TX_EDGE_RATE
- , IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
- | IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M
- | IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
- | IMX6Q_GPR13_SATA_SPD_MODE_3P0G
- | IMX6Q_GPR13_SATA_MPLL_SS_EN
- | IMX6Q_GPR13_SATA_TX_ATTEN_9_16
- | IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB
- | IMX6Q_GPR13_SATA_TX_LVL_1_025_V);
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
usleep_range(100, 200);
/*
@@ -163,11 +193,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
static void imx6q_sata_exit(struct device *dev)
{
- struct imx_ahci_priv *imxpriv = dev_get_drvdata(dev->parent);
-
- regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
+ imx_sata_clock_disable(dev);
}
static int imx_ahci_suspend(struct device *dev)
@@ -178,12 +204,8 @@ static int imx_ahci_suspend(struct device *dev)
* If no_device is set, The CLKs had been gated off in the
* initialization so don't do it again here.
*/
- if (!imxpriv->no_device) {
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- !IMX6Q_GPR13_SATA_MPLL_CLK_EN);
- clk_disable_unprepare(imxpriv->sata_ref_clk);
- }
+ if (!imxpriv->no_device)
+ imx_sata_clock_disable(dev);
return 0;
}
@@ -194,15 +216,10 @@ static int imx_ahci_resume(struct device *dev)
int ret;
if (!imxpriv->no_device) {
- ret = clk_prepare_enable(imxpriv->sata_ref_clk);
- if (ret < 0) {
- dev_err(dev, "pre-enable sata_ref clock err:%d\n", ret);
+ ret = imx_sata_clock_enable(dev, false);
+ if (ret < 0)
return ret;
- }
- regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN,
- IMX6Q_GPR13_SATA_MPLL_CLK_EN);
usleep_range(1000, 2000);
}
--
1.8.4.2
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
