Re: [PATCH 2.6.32.3] ahci: AHCI and RAID mode SATA patch for Intel Cougar Point DeviceIDs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jan 13, 2010 at 12:18 PM, Krzysztof Halasa <khc@xxxxxxxxx> wrote:
> Jeff Garzik <jgarzik@xxxxxxxxx> writes:
>
>> I'm not sure I understand your point.  Are there ahci problems with
>> the generic entries, that remain unresolved?
>
> It seems JMB363 on MSI Neo2 motherboard (P45 + ICH10R) still doesn't
> work correctly, flooding the kernel logs. No SATA devices connected,
> a CD-ROM connected to PATA (and it works fine). I've sent a report to
> the IDE  list some time ago, please let me know if you need more details
> or testing etc.
>
> JMB363 set in BIOS setup to non-RAID mode (it seems this means disabling
> the JMB BIOS). Last tested with 2.6.32.1 x86-64 SMP. IRQ 16 is shared.
>
> Currently the IRQ in PCI registers is 10 (JMB363 SATA is not handled),
> I can enable and check again if needed.
>
> 02:00.0 SATA controller: JMicron Technologies, Inc. 20360/20363 Serial ATA Controller (rev 03) (prog-if 01 [AHCI 1.0])
>        Subsystem: Micro-Star International Co., Ltd. Device 7512
>        Control: I/O+ Mem+ BusMaster+ the_rest-
>        Status: Cap+ the_rest-
>        Latency: 0, Cache Line Size: 32 bytes
>        Interrupt: pin A routed to IRQ 10
>        Region 5: Memory at fe9fe000 (32-bit, non-prefetchable) [size=8K]
>        Capabilities: <access denied>
>
> ahci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
> ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part
> ahci 0000:02:00.0: setting latency timer to 64
> scsi6 : ahci
> scsi7 : ahci
> ata7: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe100 irq 16
> ata8: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe180 irq 16
> ata8: SATA link down (SStatus 0 SControl 300)
> ata7: SATA link down (SStatus 0 SControl 300)
>
> then every few seconds (ata8 only, nothing on ata7):
>
> ata8: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
> ata8: irq_stat 0x00000040, connection status changed
> ata8: SError: { CommWake DevExch }
> ata8: hard resetting link
> ata8: SATA link down (SStatus 0 SControl 300)
> ata8: EH complete

That would seem like a board-specific problem, as I have an Asus
P7P55D PRO board with the same JMicron controller and I don't see any
such errors. The JMicron BIOS isn't enabled.

The behavior here is strange, the controller reports a connection
status change interrupt with CommWake which should indicate that some
device completed the handshake with the controller, but then the SATA
link shows down. I assume there's nothing plugged into the two JMicron
SATA ports?
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Device Mapper]

  Powered by Linux