Mikael Pettersson wrote:
Mikael Pettersson writes:
> Robert Hancock writes:
> > On 12/27/2009 02:37 PM, thomas schorpp wrote:
> > > LG GH22NS40 NL01 (possibly Renesas chipset)
> > > VIA8237 SATA (produces basically same errors), Promise SATA II 150 20579
> > > HBAs.
> > >
> > > Linux 2.6.32.2
> > > hal polling
> > > devkit polling
> > > wodim
> > > growisofs
> > >
> > > port_status 0x20280000 (Data Transfer Overrun Error & Target Device Fault)?
> > >
> > > Looks like a hardware combination incompatibility.
> > > Most applicable ATA_HORKAGES in sourcecode already tried.
> > >
> > > Not found the sense code yet since FEATURE specific according to
> > > T13/1410D revision 3b.
> > >
> > > Comments?
> > >
> > > y
> > > tom
> > >
> > > dmesg |grep -A 10 ata
> > >
> > > sata_promise 0000:00:0d.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
> > > scsi5 : sata_promise
> > > scsi6 : sata_promise
> > > scsi7 : sata_promise
> > > ata6: SATA max UDMA/133 mmio m4096@0xfbefe000 ata 0xfbefe200 irq 17
> > > ata7: SATA max UDMA/133 mmio m4096@0xfbefe000 ata 0xfbefe280 irq 17
> > > ata8: PATA max UDMA/133 mmio m4096@0xfbefe000 ata 0xfbefe300 irq 17
> > > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > > ata6.00: ATAPI: HL-DT-ST DVDRAM GH22NS40, NL01, max UDMA/100
> > > ata6.00: configured for UDMA/100
> > > scsi 5:0:0:0: CD-ROM HL-DT-ST DVDRAM GH22NS40 NL01 PQ: 0 ANSI: 5
> > > sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
> > > sr 5:0:0:0: Attached scsi CD-ROM sr0
> > > sr 5:0:0:0: Attached scsi generic sg2 type 5
> > > ata7: SATA link down (SStatus 0 SControl 300)
> > > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > > ata6.00: port_status 0x20280000
> > > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 40 00
> > > ata6.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
> > > res 51/54:03:00:00:fc/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > > ata6.00: status: { DRDY ERR }
> > > ata6: hard resetting link
> > > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > > ata6.00: configured for UDMA/100
> > > ata6: EH complete
> > > ...
> > > <period, ~10 times in series>
> > > ...
> > > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > > ata6.00: port_status 0x20280000
> > > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> > > ata6.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
> > > res 51/54:03:00:00:10/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > > ata6.00: status: { DRDY ERR }
> > > ata6: hard resetting link
> > > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > > ata6.00: configured for UDMA/100
> > > ata6: EH complete
> > > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > > ata6.00: port_status 0x20280000
> > > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> > > ata6.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
> > > res 51/54:03:00:00:10/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > > ata6.00: status: { DRDY ERR }
> > > ata6: hard resetting link
> > > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > > ata6.00: configured for UDMA/100
> > > ata6: EH complete
> > > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > > ata6.00: port_status 0x20280000
> > > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> > > ata6.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
> > > res 51/54:03:00:00:10/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > > ata6.00: status: { DRDY ERR }
> > > ata6: hard resetting link
> > > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > > ata6.00: configured for UDMA/100
> > > sr 5:0:0:0: [sr0] Result: hostbyte=0x00 driverbyte=0x08
> > > sr 5:0:0:0: [sr0] Sense Key : 0x5 [current] Info fld=0x0
> > > sr 5:0:0:0: [sr0] ASC=0x21 ASCQ=0x0
> > > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> >
> > Well, it's a READ command, and the response is "LOGICAL BLOCK ADDRESS
> > OUT OF RANGE". Seems reasonable if it's a blank disc in the drive (is it?)
> >
> > According to the code comments in sata_promise, "overrun error" means
> > the S/G byte count was larger than the drive requires. Which I suppose
> > would happen here, because the drive didn't actually transfer any data.
> > sata_promise raises an HSM error on that though which triggers resets
> > and such. Seems like an overreaction, for ATAPI commands anyway, as that
> > can happen normally. CCing Mikael.
>
> Thanks for the report. I'll try to come up with a patch to reduce
> the severity of overruns to something less than HSM.
I've looked at the available AC_ERR_ values and how they're treated by
libata-eh, and to avoid resets but allow for retries it seems that one
should use AC_ERR_OTHER, or possibly AC_ERR_DEV, or possibly no AC_ERR_
at all (i.e., zero). So please first try the patch below. If it doesn't
eliminate the reset loop, change the AC_ERR_OTHER to AC_ERR_DEV and try
again. And if that one still causes reset loops, try a plain 0.
/Mikael
--- linux-2.6.32/drivers/ata/sata_promise.c.~1~ 2009-12-03 12:38:32.000000000 +0100
+++ linux-2.6.32/drivers/ata/sata_promise.c 2010-01-03 22:08:08.000000000 +0100
@@ -862,7 +862,7 @@ static void pdc_error_intr(struct ata_po
if (port_status & PDC_DRIVE_ERR)
ac_err_mask |= AC_ERR_DEV;
if (port_status & (PDC_OVERRUN_ERR | PDC_UNDERRUN_ERR))
- ac_err_mask |= AC_ERR_HSM;
+ ac_err_mask |= AC_ERR_OTHER; /* or AC_ERR_DEV, or zero */
if (port_status & (PDC2_ATA_HBA_ERR | PDC2_ATA_DMA_CNT_ERR))
ac_err_mask |= AC_ERR_ATA_BUS;
if (port_status & (PDC_PH_ERR | PDC_SH_ERR | PDC_DH_ERR | PDC2_HTO_ERR
FIXED with AC_ERR_OTHER.
TESTED Drive reads and writes media fine.
Many Thanks :-)
y
tom
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html