On Mon, Dec 24, 2007 at 11:48:13PM +0300, Alexey Dobriyan wrote:
> Hi, I occasionally get those "soft resetting link" messages
> right after STR. Typical messages below (from photos):
>
>
> eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
> i8042 kbd 00:0a: activation failed
> sd 0:0:0:0: [sda] Starting disk
> ata2.01: ACPI cmd ef/03:44:00:00:00:b0 filtered out
> ata2.01: ACPI cmd ef/03:44:00:00:00:b0 filtered out
> ata2.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out
> ata2.01: configured for UDMA/66
> ata2.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out
> ata2.01: ACPI cmd ef/03:45:00:00:00:b0 filtered out
> ata2.01: ACPI cmd ef/03:0c:00:00:00:b0 filtered out
> ata2.01: configured for UDMA/133
> sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors (160042 MB)
> sd 2:0:0:0: [sdb] Write Protect is off
> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> ata2.01: ACPI cmd ef/03:42:00:00:00:a0 filtered out
> ata2.01: ACPI cmd ef/03:42:00:00:00:a0 filtered out
> ata2.01: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
> ata1.00: configured for UDMA/33
> sd 2:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
> sd 2:0:0:0: [sdb] Write Protect is off
> sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 2:0:0:0: [sdb] Starting disk
> ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
> ata3.00: cmd ca/00:28:ff:c0:00/00:00:00:00:00/e0 tag 0 dma 20480 out
> res 51/84:28:ff:c0:00/00:00:00:00:00/e0 Emask 0x30 (host bus error)
> ata3.00: status: { DRDY ERR }
> ata3.00: error: { ICRC ABRT }
>
> ...
>
> ata3: soft resetting link
> ata3: EH complete
> ata3.00: limiting speed to UDMA/100:PIO4
> ata3.00: BMDMA stat 0x6
> ata3.00: cmd ca/00:28:ff:c0:00/00:00:00:00:00/e0 tag 0 dma 20480 out
> res 51/84:28:ff:c0:00/00:00:00:00:00/e0 Emask 0x30 (host bus error)
> ata3.00: status: { DRDY ERR }
> ata3.00: error: { ICRC ABRT }
>
> ...
>
> ata3: soft resetting link
> ata3.00: configured for UDMA/100
> sd 2:0:0:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
> sd 2:0:0:0: [sdb] Sense Key: 0xb [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 47 00 00 00 00 0[ce] 00 0a 80 00 00 00 00 /* border of photo*/
>
> ...
>
> ata3.00: configured for UDMA/100
> ata3: EH complete
> sd 2:0:0:0: [sdb] ... 160G disk
> ...
> ata3.00: limiting speed to UDMA/33:PIO4
> ata3.00: exception Emask 0x0 Sact 0x0 Serr 0x0 action 0x2
> ata3.00: BMDMA stat 0x6
> ata3.00: cmd ca/00:08:47:66:6e/00:00:00:00:00/eb tag 0 dma 4096 out
> res 51/84:08:47:66:6e/00:00:00:00:00/eb Emask 0x30 (host bus error)
> ata3.00: status: { DRDY ERR }
> ata3.00: error: { ICRC ABRT }
> ata3: soft resetting link
host bus == PCI
So, your PCI bus is crapping itself in a major way.
One thing to try might be "libata.noacpi=1"
Jeff
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
