After looking into the HPT370 manual (now that I have it) and re-checking all
the timing tables, here's what I have discovered:
- at 33 MHz clock, PIO mode 0 timings turned to be overclocked, and all other
PIO modes underclocked;
- at 50 MHz clock, PIO modes 0 to 2 turned to be overclocked;
- at 66 MHz clock, PIO mode 0 was overclocked too.
Finally, the taskfile timing (matching PIO mode 0) turned to be overclocked at
all clock frequencies (and in all manuals)...
The new timings have been tested on HPT370 chip (at 33 MHz PCI clock) and on
HPT371N chip (at both 50 and 66 MHz DPLL clock).
Signed-off-by: Sergei Shtylyov <sshtylyov@xxxxxxxxxxxxx>
---
Many PIO modes at 55/66 MHz (as well as MDDMA modes at all clocks) are also
underclocked but I decided not to touch them, at least for the time being.
The patch is against the Linus' tree, with PIO0 setup time correct this time...
drivers/ide/pci/hpt366.c | 71 ++++++++++++++++++++++++++++++++++++++++++++++-
1 files changed, 70 insertions(+), 1 deletion(-)
Index: linux-2.6/drivers/ide/pci/hpt366.c
===================================================================
--- linux-2.6.orig/drivers/ide/pci/hpt366.c
+++ linux-2.6/drivers/ide/pci/hpt366.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/ide/pci/hpt366.c Version 1.21 Oct 23, 2007
+ * linux/drivers/ide/pci/hpt366.c Version 1.22 Dec 4, 2007
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@xxxxxxxxxxxxx>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
@@ -310,6 +310,8 @@ static u32 twenty_five_base_hpt36x[] = {
/* XFER_PIO_0 */ 0xc0d08585
};
+#if 0
+/* These are the timing tables from the HighPoint open source drivers... */
static u32 thirty_three_base_hpt37x[] = {
/* XFER_UDMA_6 */ 0x12446231, /* 0x12646231 ?? */
/* XFER_UDMA_5 */ 0x12446231,
@@ -369,6 +371,73 @@ static u32 sixty_six_base_hpt37x[] = {
/* XFER_PIO_1 */ 0x0d029d26,
/* XFER_PIO_0 */ 0x0d029d5e
};
+#else
+/*
+ * The following are the new timing tables with PIO mode data/taskfile transfer
+ * overclocking fixed...
+ */
+
+/* This table is taken from the HPT370 data manual rev. 1.02 */
+static u32 thirty_three_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x16455031, /* 0x16655031 ?? */
+ /* XFER_UDMA_5 */ 0x16455031,
+ /* XFER_UDMA_4 */ 0x16455031,
+ /* XFER_UDMA_3 */ 0x166d5031,
+ /* XFER_UDMA_2 */ 0x16495031,
+ /* XFER_UDMA_1 */ 0x164d5033,
+ /* XFER_UDMA_0 */ 0x16515097,
+
+ /* XFER_MW_DMA_2 */ 0x26515031,
+ /* XFER_MW_DMA_1 */ 0x26515033,
+ /* XFER_MW_DMA_0 */ 0x26515097,
+
+ /* XFER_PIO_4 */ 0x06515021,
+ /* XFER_PIO_3 */ 0x06515022,
+ /* XFER_PIO_2 */ 0x06515033,
+ /* XFER_PIO_1 */ 0x06915065,
+ /* XFER_PIO_0 */ 0x06d1508a
+};
+
+static u32 fifty_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x1a861842,
+ /* XFER_UDMA_5 */ 0x1a861842,
+ /* XFER_UDMA_4 */ 0x1aae1842,
+ /* XFER_UDMA_3 */ 0x1a8e1842,
+ /* XFER_UDMA_2 */ 0x1a0e1842,
+ /* XFER_UDMA_1 */ 0x1a161854,
+ /* XFER_UDMA_0 */ 0x1a1a18ea,
+
+ /* XFER_MW_DMA_2 */ 0x2a821842,
+ /* XFER_MW_DMA_1 */ 0x2a821854,
+ /* XFER_MW_DMA_0 */ 0x2a8218ea,
+
+ /* XFER_PIO_4 */ 0x0a821842,
+ /* XFER_PIO_3 */ 0x0a821843,
+ /* XFER_PIO_2 */ 0x0a821855,
+ /* XFER_PIO_1 */ 0x0ac218a8,
+ /* XFER_PIO_0 */ 0x0b02190c
+};
+
+static u32 sixty_six_base_hpt37x[] = {
+ /* XFER_UDMA_6 */ 0x1c86fe62,
+ /* XFER_UDMA_5 */ 0x1caefe62, /* 0x1c8afe62 */
+ /* XFER_UDMA_4 */ 0x1c8afe62,
+ /* XFER_UDMA_3 */ 0x1c8efe62,
+ /* XFER_UDMA_2 */ 0x1c92fe62,
+ /* XFER_UDMA_1 */ 0x1c9afe62,
+ /* XFER_UDMA_0 */ 0x1c82fe62,
+
+ /* XFER_MW_DMA_2 */ 0x2c82fe62,
+ /* XFER_MW_DMA_1 */ 0x2c82fe66,
+ /* XFER_MW_DMA_0 */ 0x2c82ff2e,
+
+ /* XFER_PIO_4 */ 0x0c82fe62,
+ /* XFER_PIO_3 */ 0x0c82fe84,
+ /* XFER_PIO_2 */ 0x0c82fea6,
+ /* XFER_PIO_1 */ 0x0d02ff26,
+ /* XFER_PIO_0 */ 0x0d42ff7f
+};
+#endif
#define HPT366_DEBUG_DRIVE_INFO 0
#define HPT371_ALLOW_ATA133_6 1
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
