on., 28.11.2007 kl. 10.09 +0900, skrev Tejun Heo: > Kjartan Maraas wrote: > > I get this exact error message on a normal first time boot here. I'm > > using the latest fedora development kernel which is 2.6.24-rc2-git6 > > based. And I have the latest BIOS from HP IIRC. > > > > This is an HP nc6400 intel based laptop: > > Care to post boot dmesg? Or does harddisk detection fail because of this? > Here you go. It shows the error two times and then it gets it right and continues to boot. No other problems arise from this that I can see. libata version 3.00 loaded. ahci 0000:00:1f.2: version 3.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 21 (level, low) -> IRQ 22 ahci 0000:00:1f.2: nr_ports (4) and implemented port map (0x1) don't match, using nr_ports ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf usb 2-1: new full speed USB device using uhci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 abar m1024@0xf4785000 port 0xf4785100 irq 220 ata2: SATA max UDMA/133 abar m1024@0xf4785000 port 0xf4785180 irq 220 ata3: SATA max UDMA/133 abar m1024@0xf4785000 port 0xf4785200 irq 220 ata4: SATA max UDMA/133 abar m1024@0xf4785000 port 0xf4785280 irq 220 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 failed (Emask=0x1 Stat=0x51 Err=0x04) ata1: failed to recover some devices, retrying in 5 secs input: PS/2 Generic Mouse as /class/input/input3 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 failed (Emask=0x1 Stat=0x51 Err=0x04) ata1.00: ACPI on devcfg failed the second time, disabling (errno=-5) ata1.00: revalidation failed (errno=1) ata1: failed to recover some devices, retrying in 5 secs ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: configured for UDMA/100 ata2: SATA link down (SStatus 0 SControl 0) ata3: SATA link down (SStatus 0 SControl 0) ata4: SATA link down (SStatus 0 SControl 0) scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2080B 892C PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk insmod used greatest stack depth: 596 bytes left EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds Cheers Kjartan - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
