> On Wed, 07 Nov 2007 15:15:07 +0100 Roberto Oppedisano <roppedisano@xxxxxxxxxxxxxx> wrote: > Hello. > I noticed that after suspending to ram the DVD-ROM/CDRW > drive in no more recognized on my laptop. Looking at dmesg > after suspend i found: > > [ 5.313446] ata2.00: _GTF unexpected object type 0x1 > [ 5.313453] ata2.00: ACPI on devcfg failed the second time, disabling > (errno=-22) > [ 5.313457] ata2.00: revalidation failed (errno=1) > [ 5.313459] ata2.00: disabled > > > Not sure when the bug was introduced or if it has been always been there > (but I can investigate if needed). > > More details on request. > > Following dmesg pre and after suspend. > Yes, it would be useful if you could work ot whether this worked OK in an earlier kernel, thanks. > > - pre suspend > > roppedisano@poppero1:~$ dmesg > 3700] io scheduler noop registered > [ 11.443745] io scheduler anticipatory registered (default) > [ 11.443792] io scheduler deadline registered > [ 11.443896] io scheduler cfq registered > [ 11.444006] Boot video device is 0000:01:00.0 > [ 11.464741] Real Time Clock Driver v1.12ac > [ 11.464794] Linux agpgart interface v0.102 > [ 11.464880] agpgart: Detected an Intel 855PM Chipset. > [ 11.479558] agpgart: AGP aperture is 256M @ 0xb0000000 > [ 11.479673] ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2 > [ 11.479723] ipw2100: Copyright(c) 2003-2006 Intel Corporation > [ 11.479888] ata_piix 0000:00:1f.1: version 2.12 > [ 11.479901] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) > [ 11.479955] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI > 5 (level, low) -> IRQ 5 > [ 11.480114] PCI: Setting latency timer of device 0000:00:1f.1 to 64 > [ 11.480185] scsi0 : ata_piix > [ 11.480282] scsi1 : ata_piix > [ 11.480425] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4c40 > irq 14 > [ 11.480475] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4c48 > irq 15 > [ 11.671876] ata1.00: ATA-7: WDC WD1000UE-00KVT0, 01.03K01, max UDMA/100 > [ 11.671926] ata1.00: 195371568 sectors, multi 16: LBA48 > [ 11.675442] ata1.00: configured for UDMA/100 > [ 11.924993] Switched to high resolution mode on CPU 0 > [ 12.052537] ata2.00: ATAPI: SD-R2512, 1A04, max MWDMA2 > [ 12.228484] ata2.00: configured for MWDMA2 > [ 12.229348] scsi 0:0:0:0: Direct-Access ATA WDC WD1000UE-00K > 01.0 PQ: 0 ANSI: 5 > [ 12.229506] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors > (100030 MB) > [ 12.229565] sd 0:0:0:0: [sda] Write Protect is off > [ 12.229613] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 12.229627] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 12.229726] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors > (100030 MB) > [ 12.229781] sd 0:0:0:0: [sda] Write Protect is off > [ 12.229828] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 12.229841] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 12.229902] sda: sda1 sda2 < sda5 sda6 > > [ 12.302219] sd 0:0:0:0: [sda] Attached SCSI disk > [ 12.307592] scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-R2512 > 1A04 PQ: 0 ANSI: 5 > [ 12.307853] PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at > 0x60,0x64 irq 1,12 > [ 12.317941] i8042.c: Detected active multiplexing controller, rev 1.1. > [ 12.323459] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 12.323542] serio: i8042 AUX0 port at 0x60,0x64 irq 12 > [ 12.323590] serio: i8042 AUX1 port at 0x60,0x64 irq 12 > [ 12.323638] serio: i8042 AUX2 port at 0x60,0x64 irq 12 > [ 12.323685] serio: i8042 AUX3 port at 0x60,0x64 irq 12 > [ 12.323933] mice: PS/2 mouse device common for all mice > [ 12.346985] input: AT Translated Set 2 keyboard as /class/input/input0 > [ 12.360775] cpuidle: using governor ladder > [ 12.360821] cpuidle: using governor menu > [ 12.360951] TCP cubic registered > [ 12.361002] NET: Registered protocol family 1 > [ 12.361059] NET: Registered protocol family 17 > [ 12.361107] ieee80211: 802.11 data/management/control stack, git-1.1.13 > [ 12.361156] ieee80211: Copyright (C) 2004-2005 Intel Corporation > <jketreno@xxxxxxxxxxxxxxx> > [ 12.361226] ieee80211_crypt: registered algorithm 'NULL' > [ 12.361230] Using IPI Shortcut mode > [ 13.038080] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, > caps: 0x904713/0x10008 > [ 13.089011] input: SynPS/2 Synaptics TouchPad as /class/input/input1 > [ 13.223554] kjournald starting. Commit interval 5 seconds > [ 13.223608] EXT3-fs: mounted filesystem with ordered data mode. > [ 13.223661] VFS: Mounted root (ext3 filesystem) readonly. > [ 13.223809] Freeing unused kernel memory: 152k freed > [ 16.737952] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray > [ 16.738035] Uniform CD-ROM driver Revision: 3.20 > [ 16.738133] sr 1:0:0:0: Attached scsi CD-ROM sr0 > [ 16.815873] usbcore: registered new interface driver usbfs > [ 16.815949] usbcore: registered new interface driver hub > [ 16.817658] usbcore: registered new device driver usb > [ 16.859293] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 16.859368] sr 1:0:0:0: Attached scsi generic sg1 type 5 > [ 16.872367] ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10 > [ 16.872420] PCI: setting IRQ 10 as level-triggered > [ 16.872424] ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 16.872554] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt > [ 17.025230] input: Power Button (FF) as /class/input/input2 > [ 17.030684] ACPI: Power Button (FF) [PWRF] > [ 17.030813] input: Power Button (CM) as /class/input/input3 > [ 17.037689] ACPI: Power Button (CM) [C1BE] > [ 17.037783] input: Lid Switch as /class/input/input4 > [ 17.041787] ACPI: Lid Switch [C136] > [ 17.046878] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) > [ 17.047050] ACPI: Processor [CPU0] (supports 8 throttling states) > [ 17.096295] USB Universal Host Controller Interface driver v3.0 > [ 17.097066] ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10 > [ 17.097116] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 17.097247] PCI: Setting latency timer of device 0000:00:1d.0 to 64 > [ 17.097251] uhci_hcd 0000:00:1d.0: UHCI Host Controller > [ 17.097566] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned > bus number 1 > [ 17.097647] uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0 > [ 17.097849] usb usb1: configuration #1 chosen from 1 choice > [ 17.097927] hub 1-0:1.0: USB hub found > [ 17.097978] hub 1-0:1.0: 2 ports detected > [ 17.199123] ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5 > [ 17.199179] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI > 5 (level, low) -> IRQ 5 > [ 17.199309] PCI: Setting latency timer of device 0000:00:1d.1 to 64 > [ 17.199314] uhci_hcd 0000:00:1d.1: UHCI Host Controller > [ 17.199386] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned > bus number 2 > [ 17.199467] uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0 > [ 17.199626] usb usb2: configuration #1 chosen from 1 choice > [ 17.199712] hub 2-0:1.0: USB hub found > [ 17.199762] hub 2-0:1.0: 2 ports detected > [ 17.300845] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI > 5 (level, low) -> IRQ 5 > [ 17.300984] PCI: Setting latency timer of device 0000:00:1d.2 to 64 > [ 17.300988] uhci_hcd 0000:00:1d.2: UHCI Host Controller > [ 17.301058] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned > bus number 3 > [ 17.301138] uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00 > [ 17.301302] usb usb3: configuration #1 chosen from 1 choice > [ 17.301378] hub 3-0:1.0: USB hub found > [ 17.301427] hub 3-0:1.0: 2 ports detected > [ 17.313015] ACPI: AC Adapter [C134] (on-line) > [ 17.322009] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) > [ 17.356141] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, > 1.2.2kmprq > [ 17.356387] ipw2200: Copyright(c) 2003-2006 Intel Corporation > [ 17.384259] ACPI: Battery Slot [C11F] (battery present) > [ 17.384567] input: Video Bus as /class/input/input5 > [ 17.391776] ACPI: Video Device [C0D0] (multi-head: yes rom: no > post: no) > [ 17.402197] ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5 > [ 17.402251] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI > 5 (level, low) -> IRQ 5 > [ 17.402384] PCI: Setting latency timer of device 0000:00:1d.7 to 64 > [ 17.402388] ehci_hcd 0000:00:1d.7: EHCI Host Controller > [ 17.402460] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned > bus number 4 > [ 17.406415] ehci_hcd 0000:00:1d.7: debug port 1 > [ 17.406465] PCI: cache line size of 32 is not supported by device > 0000:00:1d.7 > [ 17.406473] ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000 > [ 17.409711] usb 1-1: new full speed USB device using uhci_hcd and > address 2 > [ 17.411845] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver > 10 Dec 2004 > [ 17.412005] usb usb4: configuration #1 chosen from 1 choice > [ 17.412079] hub 4-0:1.0: USB hub found > [ 17.412128] hub 4-0:1.0: 6 ports detected > [ 17.473565] wbsd: Winbond W83L51xD SD/MMC card interface driver > [ 17.473621] wbsd: Copyright(c) Pierre Ossman > [ 17.474374] wbsd 00:02: activated > [ 17.479535] mmc0: W83L51xD id 7112 at 0x248 irq 6 dma 0 PnP > [ 17.512862] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 17.513474] eth0: RTL-8139C+ at 0xf8830000, 00:0f:b0:0e:de:a8, IRQ 10 > [ 17.513614] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI > 5 (level, low) -> IRQ 5 > [ 17.519105] NET: Registered protocol family 23 > [ 17.521512] ipw2200: Detected Intel PRO/Wireless 2200BG Network > Connection > [ 17.535301] Detected unconfigured Compaq x1000 family SMSC IrDA chip, > pre-configuring device. > [ 17.535367] Setting up Intel 82801 controller and SMSC device > [ 17.535537] found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): > LPC47N227 > [ 17.535600] smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, > irq: 7, mode: 0x0e > [ 17.535670] SMsC IrDA Controller found > [ 17.535671] IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7 > [ 17.535831] No transceiver found. Defaulting to Fast pin select > [ 17.635719] Marking TSC unstable due to: TSC halts in idle. > [ 17.635781] Time: acpi_pm clocksource has been installed. > [ 17.783728] usb 4-1: new high speed USB device using ehci_hcd and > address 2 > [ 17.899592] usb 4-1: configuration #1 chosen from 1 choice > [ 17.934233] ipw2200: Radio Frequency Kill Switch is On: > [ 17.934235] Kill switch must be turned off for wireless networking to > work. > [ 17.937560] IrDA: Registered device irda0 > [ 17.945309] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 > 802.11a channels) > [ 17.945422] Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860] > [ 17.945487] Yenta: Using CSCINT to route CSC interrupts to PCI > [ 17.945535] Yenta: Routing CardBus interrupts to PCI > [ 17.945584] Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44 > [ 17.959053] udev: renamed network interface eth1 to eth2 > [ 17.963928] Initializing USB Mass Storage driver... > [ 18.054764] scsi2 : SCSI emulation for USB Mass Storage devices > [ 18.055003] usbcore: registered new interface driver usb-storage > [ 18.055054] USB Mass Storage support registered. > [ 18.056582] usb-storage: device found at 2 > [ 18.056585] usb-storage: waiting for device to settle before scanning > [ 18.168110] Yenta: ISA IRQ mask 0x0898, PCI irq 5 > [ 18.168161] Socket status: 30000006 > [ 18.168206] Yenta: Raising subordinate bus# of parent bus (#02) from > #03 to #06 > [ 18.168268] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff > [ 18.168318] cs: IO port probe 0x2000-0x2fff: clean. > [ 18.168623] pcmcia: parent PCI bridge Memory window: 0x90000000 - > 0x903fffff > [ 18.169296] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 18.224489] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] > MMIO=[90200000-902007ff] Max Packet=[2048] IR/IT contexts=[4/8] > [ 18.229750] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 18.229886] PCI: Setting latency timer of device 0000:00:1f.5 to 64 > [ 18.358686] usb 3-1: new low speed USB device using uhci_hcd and > address 2 > [ 18.518968] usb 3-1: configuration #1 chosen from 1 choice > [ 18.595042] usbcore: registered new interface driver hiddev > [ 18.608225] input: PS/2+USB Mouse as /class/input/input6 > [ 18.613904] input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on > usb-0000:00:1d.2-1 > [ 18.614093] usbcore: registered new interface driver usbhid > [ 18.614142] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver > [ 18.676639] cs: IO port probe 0x100-0x4ff: excluding 0x140-0x14f > 0x200-0x20f 0x378-0x37f > [ 18.679305] cs: IO port probe 0x800-0x8ff: clean. > [ 18.680107] cs: IO port probe 0xc00-0xcff: clean. > [ 18.680953] cs: IO port probe 0xa00-0xaff: clean. > [ 19.041708] intel8x0_measure_ac97_clock: measured 50439 usecs > [ 19.041762] intel8x0: clocking to 48000 > [ 19.043620] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 19.043771] PCI: Setting latency timer of device 0000:00:1f.6 to 64 > [ 19.487840] ieee1394: Host added: ID:BUS[0-00:1023] > GUID[00023f494a405951] > [ 20.432072] Adding 971892k swap on /dev/sda5. Priority:-1 extents:1 > across:971892k > [ 20.708471] EXT3 FS on sda6, internal journal > [ 21.386927] IA-32 Microcode Update Driver: v1.14a > <tigran@xxxxxxxxxxxxxxxxxxxx> > [ 21.419174] usbcore: registered new interface driver usbserial > [ 21.419238] drivers/usb/serial/usb-serial.c: USB Serial support > registered for generic > [ 21.419310] usbcore: registered new interface driver usbserial_generic > [ 21.419359] drivers/usb/serial/usb-serial.c: USB Serial Driver core > [ 21.501969] device-mapper: uevent: version 1.0.3 > [ 21.502043] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) > initialised: dm-devel@xxxxxxxxxx > [ 21.885393] NTFS driver 2.1.29 [Flags: R/W MODULE]. > [ 21.975324] NTFS volume version 3.1. > [ 21.975377] NTFS-fs warning (device sda1): load_system_files(): > Unsupported volume flags 0x4000 encountered. > [ 21.975440] NTFS-fs error (device sda1): load_system_files(): Volume > has unsupported flags set. Mounting read-only. Run chkdsk and mount in > Windows. > [ 23.056920] scsi 2:0:0:0: Direct-Access USB 2.0 Flash Disk > 1100 PQ: 0 ANSI: 0 CCS > [ 23.061899] sd 2:0:0:0: [sdb] 3963904 512-byte hardware sectors (2030 MB) > [ 23.062893] sd 2:0:0:0: [sdb] Write Protect is off > [ 23.062941] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 > [ 23.062944] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [ 23.065516] sd 2:0:0:0: [sdb] 3963904 512-byte hardware sectors (2030 MB) > [ 23.066515] sd 2:0:0:0: [sdb] Write Protect is off > [ 23.066563] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 > [ 23.066565] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [ 23.066615] sdb: sdb1 > [ 23.067639] sd 2:0:0:0: [sdb] Attached SCSI removable disk > [ 23.067728] sd 2:0:0:0: Attached scsi generic sg2 type 0 > [ 23.067976] usb-storage: device scan complete > [ 24.114262] ieee80211_crypt: registered algorithm 'WEP' > [ 24.924188] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 > [ 42.014307] Clocksource tsc unstable (delta = -135778174 ns) > [ 71.993044] NET: Registered protocol family 10 > [ 71.997147] lo: Disabled Privacy Extensions > [ 71.998745] ADDRCONF(NETDEV_UP): eth2: link is not ready > [ 78.327134] usbcore: registered new interface driver usblp > [ 41.561843] Bluetooth: Core ver 2.11 > [ 41.561961] NET: Registered protocol family 31 > [ 41.562007] Bluetooth: HCI device and connection manager initialized > [ 41.562056] Bluetooth: HCI socket layer initialized > [ 41.613902] Bluetooth: L2CAP ver 2.9 > [ 41.615504] Bluetooth: L2CAP socket layer initialized > [ 41.694692] Bluetooth: RFCOMM socket layer initialized > [ 41.694913] Bluetooth: RFCOMM TTY layer initialized > [ 41.694961] Bluetooth: RFCOMM ver 1.8 > [ 43.781048] [drm] Initialized drm 1.1.0 20060810 > [ 43.785506] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 43.786123] [drm] Initialized radeon 1.28.0 20060524 on minor 0 > [ 45.160388] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. > [ 45.160518] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode > [ 45.160550] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode > [ 123.009876] [drm] Setting GART location based on new memory map > [ 123.010070] [drm] Loading R200 Microcode > [ 123.010133] [drm] writeback test succeeded in 2 usecs > > > > poppero1:/home/roppedisano# s2ram > Switching from vt7 to vt1 > Calling save_state > Allocated buffer at 0x2010 (base is 0x0) > ES: 0x0201 EBX: 0x0000 > Calling get_mode > Calling restore_state_from > Function not supported? > Calling set_vbe_mode > switching back to vt7 > > > - after suspend > > roppedisano@poppero1:~$ dmesg > ime: acpi_pm clocksource has been installed. > [ 17.783728] usb 4-1: new high speed USB device using ehci_hcd and > address 2 > [ 17.899592] usb 4-1: configuration #1 chosen from 1 choice > [ 17.934233] ipw2200: Radio Frequency Kill Switch is On: > [ 17.934235] Kill switch must be turned off for wireless networking to > work. > [ 17.937560] IrDA: Registered device irda0 > [ 17.945309] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 > 802.11a channels) > [ 17.945422] Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860] > [ 17.945487] Yenta: Using CSCINT to route CSC interrupts to PCI > [ 17.945535] Yenta: Routing CardBus interrupts to PCI > [ 17.945584] Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44 > [ 17.959053] udev: renamed network interface eth1 to eth2 > [ 17.963928] Initializing USB Mass Storage driver... > [ 18.054764] scsi2 : SCSI emulation for USB Mass Storage devices > [ 18.055003] usbcore: registered new interface driver usb-storage > [ 18.055054] USB Mass Storage support registered. > [ 18.056582] usb-storage: device found at 2 > [ 18.056585] usb-storage: waiting for device to settle before scanning > [ 18.168110] Yenta: ISA IRQ mask 0x0898, PCI irq 5 > [ 18.168161] Socket status: 30000006 > [ 18.168206] Yenta: Raising subordinate bus# of parent bus (#02) from > #03 to #06 > [ 18.168268] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff > [ 18.168318] cs: IO port probe 0x2000-0x2fff: clean. > [ 18.168623] pcmcia: parent PCI bridge Memory window: 0x90000000 - > 0x903fffff > [ 18.169296] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 18.224489] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] > MMIO=[90200000-902007ff] Max Packet=[2048] IR/IT contexts=[4/8] > [ 18.229750] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 18.229886] PCI: Setting latency timer of device 0000:00:1f.5 to 64 > [ 18.358686] usb 3-1: new low speed USB device using uhci_hcd and > address 2 > [ 18.518968] usb 3-1: configuration #1 chosen from 1 choice > [ 18.595042] usbcore: registered new interface driver hiddev > [ 18.608225] input: PS/2+USB Mouse as /class/input/input6 > [ 18.613904] input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on > usb-0000:00:1d.2-1 > [ 18.614093] usbcore: registered new interface driver usbhid > [ 18.614142] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver > [ 18.676639] cs: IO port probe 0x100-0x4ff: excluding 0x140-0x14f > 0x200-0x20f 0x378-0x37f > [ 18.679305] cs: IO port probe 0x800-0x8ff: clean. > [ 18.680107] cs: IO port probe 0xc00-0xcff: clean. > [ 18.680953] cs: IO port probe 0xa00-0xaff: clean. > [ 19.041708] intel8x0_measure_ac97_clock: measured 50439 usecs > [ 19.041762] intel8x0: clocking to 48000 > [ 19.043620] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 19.043771] PCI: Setting latency timer of device 0000:00:1f.6 to 64 > [ 19.487840] ieee1394: Host added: ID:BUS[0-00:1023] > GUID[00023f494a405951] > [ 20.432072] Adding 971892k swap on /dev/sda5. Priority:-1 extents:1 > across:971892k > [ 20.708471] EXT3 FS on sda6, internal journal > [ 21.386927] IA-32 Microcode Update Driver: v1.14a > <tigran@xxxxxxxxxxxxxxxxxxxx> > [ 21.419174] usbcore: registered new interface driver usbserial > [ 21.419238] drivers/usb/serial/usb-serial.c: USB Serial support > registered for generic > [ 21.419310] usbcore: registered new interface driver usbserial_generic > [ 21.419359] drivers/usb/serial/usb-serial.c: USB Serial Driver core > [ 21.501969] device-mapper: uevent: version 1.0.3 > [ 21.502043] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) > initialised: dm-devel@xxxxxxxxxx > [ 21.885393] NTFS driver 2.1.29 [Flags: R/W MODULE]. > [ 21.975324] NTFS volume version 3.1. > [ 21.975377] NTFS-fs warning (device sda1): load_system_files(): > Unsupported volume flags 0x4000 encountered. > [ 21.975440] NTFS-fs error (device sda1): load_system_files(): Volume > has unsupported flags set. Mounting read-only. Run chkdsk and mount in > Windows. > [ 23.056920] scsi 2:0:0:0: Direct-Access USB 2.0 Flash Disk > 1100 PQ: 0 ANSI: 0 CCS > [ 23.061899] sd 2:0:0:0: [sdb] 3963904 512-byte hardware sectors (2030 MB) > [ 23.062893] sd 2:0:0:0: [sdb] Write Protect is off > [ 23.062941] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 > [ 23.062944] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [ 23.065516] sd 2:0:0:0: [sdb] 3963904 512-byte hardware sectors (2030 MB) > [ 23.066515] sd 2:0:0:0: [sdb] Write Protect is off > [ 23.066563] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00 > [ 23.066565] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [ 23.066615] sdb: sdb1 > [ 23.067639] sd 2:0:0:0: [sdb] Attached SCSI removable disk > [ 23.067728] sd 2:0:0:0: Attached scsi generic sg2 type 0 > [ 23.067976] usb-storage: device scan complete > [ 24.114262] ieee80211_crypt: registered algorithm 'WEP' > [ 24.924188] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 > [ 42.014307] Clocksource tsc unstable (delta = -135778174 ns) > [ 71.993044] NET: Registered protocol family 10 > [ 71.997147] lo: Disabled Privacy Extensions > [ 71.998745] ADDRCONF(NETDEV_UP): eth2: link is not ready > [ 78.327134] usbcore: registered new interface driver usblp > [ 41.561843] Bluetooth: Core ver 2.11 > [ 41.561961] NET: Registered protocol family 31 > [ 41.562007] Bluetooth: HCI device and connection manager initialized > [ 41.562056] Bluetooth: HCI socket layer initialized > [ 41.613902] Bluetooth: L2CAP ver 2.9 > [ 41.615504] Bluetooth: L2CAP socket layer initialized > [ 41.694692] Bluetooth: RFCOMM socket layer initialized > [ 41.694913] Bluetooth: RFCOMM TTY layer initialized > [ 41.694961] Bluetooth: RFCOMM ver 1.8 > [ 43.781048] [drm] Initialized drm 1.1.0 20060810 > [ 43.785506] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 43.786123] [drm] Initialized radeon 1.28.0 20060524 on minor 0 > [ 45.160388] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. > [ 45.160518] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode > [ 45.160550] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode > [ 123.009876] [drm] Setting GART location based on new memory map > [ 123.010070] [drm] Loading R200 Microcode > [ 123.010133] [drm] writeback test succeeded in 2 usecs > [ 555.546384] Syncing filesystems ... done. > [ 555.995405] Freezing user space processes ... (elapsed 0.02 seconds) > done. > [ 556.015925] Freezing remaining freezable tasks ... (elapsed 0.00 > seconds) done. > [ 556.016084] Suspending console(s) > [ 556.094907] sd 0:0:0:0: [sda] Synchronizing SCSI cache > [ 556.095062] sd 0:0:0:0: [sda] Stopping disk > [ 556.096308] ACPI handle has no context! > [ 556.096578] wbsd 00:02: disabled > [ 556.096637] eth2: Going into suspend... > [ 556.096672] ACPI: PCI interrupt for device 0000:02:02.0 disabled > [ 556.096677] ACPI handle has no context! > [ 556.102017] ACPI handle has no context! > [ 556.113013] ACPI: PCI interrupt for device 0000:00:1f.6 disabled > [ 556.124013] codec_write 0: semaphore is not ready for register 0x26 > [ 556.124019] ACPI: PCI interrupt for device 0000:00:1f.5 disabled > [ 556.124686] ACPI: PCI interrupt for device 0000:00:1f.1 disabled > [ 556.124771] ACPI: PCI interrupt for device 0000:00:1d.7 disabled > [ 556.124920] ACPI: PCI interrupt for device 0000:00:1d.2 disabled > [ 556.124946] ACPI: PCI interrupt for device 0000:00:1d.1 disabled > [ 556.124972] ACPI: PCI interrupt for device 0000:00:1d.0 disabled > [ 0.445798] Intel machine check architecture supported. > [ 0.445805] Intel machine check reporting enabled on CPU#0. > [ 0.445812] Back to C! > [ 0.454486] PCI: Enabling device 0000:00:1d.0 (0000 -> 0001) > [ 0.454491] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 0.454499] PCI: Setting latency timer of device 0000:00:1d.0 to 64 > [ 0.454505] PM: Writing back config space on device 0000:00:1d.0 at > offset f (was 100, writing 10a) > [ 0.454517] PM: Writing back config space on device 0000:00:1d.0 at > offset 8 (was 1, writing 48c1) > [ 0.454546] usb usb1: root hub lost power or was reset > [ 0.454561] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001) > [ 0.454565] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI > 5 (level, low) -> IRQ 5 > [ 0.454572] PCI: Setting latency timer of device 0000:00:1d.1 to 64 > [ 0.454577] PM: Writing back config space on device 0000:00:1d.1 at > offset f (was 200, writing 205) > [ 0.454589] PM: Writing back config space on device 0000:00:1d.1 at > offset 8 (was 1, writing 48e1) > [ 0.454616] usb usb2: root hub lost power or was reset > [ 0.454630] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001) > [ 0.454633] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI > 5 (level, low) -> IRQ 5 > [ 0.454640] PCI: Setting latency timer of device 0000:00:1d.2 to 64 > [ 0.454646] PM: Writing back config space on device 0000:00:1d.2 at > offset f (was 300, writing 305) > [ 0.454658] PM: Writing back config space on device 0000:00:1d.2 at > offset 8 (was 1, writing 4c01) > [ 0.454685] usb usb3: root hub lost power or was reset > [ 0.464886] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002) > [ 0.464889] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI > 5 (level, low) -> IRQ 5 > [ 0.464897] PCI: Setting latency timer of device 0000:00:1d.7 to 64 > [ 0.464909] PM: Writing back config space on device 0000:00:1d.7 at > offset f (was 400, writing 405) > [ 0.464927] PM: Writing back config space on device 0000:00:1d.7 at > offset 4 (was 0, writing a0000000) > [ 0.464957] PM: Writing back config space on device 0000:00:1e.0 at > offset 7 (was 22802020, writing 2802020) > [ 0.464974] PCI: Setting latency timer of device 0000:00:1e.0 to 64 > [ 0.465001] PM: Writing back config space on device 0000:00:1f.1 at > offset f (was 100, writing 105) > [ 0.465012] PM: Writing back config space on device 0000:00:1f.1 at > offset 9 (was 0, writing 50000000) > [ 0.465030] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI > 5 (level, low) -> IRQ 5 > [ 0.465036] PCI: Setting latency timer of device 0000:00:1f.1 to 64 > [ 0.466472] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 0.466479] PCI: Setting latency timer of device 0000:00:1f.5 to 64 > [ 0.925828] ata2.00: _GTF unexpected object type 0x1 > [ 0.925831] ata2.00: revalidation failed (errno=-22) > [ 0.925833] ata2: failed to recover some devices, retrying in 5 secs > [ 1.482119] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI > 10 (level, low) -> IRQ 10 > [ 1.482126] PCI: Setting latency timer of device 0000:00:1f.6 to 64 > [ 1.848445] ipw2200: Unable to load ucode: -22 > [ 1.848472] ipw2200: Unable to load firmware: -22 > [ 1.848474] ipw2200: Failed to up device > [ 2.486789] PM: Writing back config space on device 0000:01:00.0 at > offset 6 (was 0, writing 90400000) > [ 2.486796] PM: Writing back config space on device 0000:01:00.0 at > offset 3 (was 0, writing 8008) > [ 2.486815] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI > 10 (level, low) -> IRQ 10 > [ 2.497297] PM: Writing back config space on device 0000:02:00.0 at > offset f (was 20000100, writing 2000010a) > [ 2.497312] PM: Writing back config space on device 0000:02:00.0 at > offset 5 (was 1, writing 2401) > [ 2.497317] PM: Writing back config space on device 0000:02:00.0 at > offset 4 (was 0, writing 90200000) > [ 2.497322] PM: Writing back config space on device 0000:02:00.0 at > offset 3 (was 0, writing 8008) > [ 2.497328] PM: Writing back config space on device 0000:02:00.0 at > offset 1 (was 2100080, writing 2100007) > [ 2.550487] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] > MMIO=[90200000-902007ff] Max Packet=[1024] IR/IT contexts=[4/8] > [ 2.563619] PM: Writing back config space on device 0000:02:01.0 at > offset 1 (was 2900007, writing 2900017) > [ 2.563653] eth2: Coming out of suspend... > [ 2.563759] PCI: Enabling device 0000:02:02.0 (0000 -> 0002) > [ 2.563763] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI > 5 (level, low) -> IRQ 5 > [ 2.563773] PM: Writing back config space on device 0000:02:02.0 at > offset f (was 18030100, writing 1803010b) > [ 2.563789] PM: Writing back config space on device 0000:02:02.0 at > offset 4 (was 0, writing 90000000) > [ 2.563794] PM: Writing back config space on device 0000:02:02.0 at > offset 3 (was 0, writing 8008) > [ 2.563800] PM: Writing back config space on device 0000:02:02.0 at > offset 1 (was 2900002, writing 2900006) > [ 2.563862] PM: Writing back config space on device 0000:02:04.0 at > offset f (was 34001ff, writing 5c00105) > [ 2.563868] PM: Writing back config space on device 0000:02:04.0 at > offset e (was 0, writing 2cfc) > [ 2.563873] PM: Writing back config space on device 0000:02:04.0 at > offset d (was 0, writing 2c00) > [ 2.563878] PM: Writing back config space on device 0000:02:04.0 at > offset c (was 0, writing 28fc) > [ 2.563883] PM: Writing back config space on device 0000:02:04.0 at > offset b (was 0, writing 2800) > [ 2.563888] PM: Writing back config space on device 0000:02:04.0 at > offset a (was 0, writing 5bfff000) > [ 2.563893] PM: Writing back config space on device 0000:02:04.0 at > offset 9 (was 0, writing 58000000) > [ 2.563898] PM: Writing back config space on device 0000:02:04.0 at > offset 8 (was 0, writing 57fff000) > [ 2.563903] PM: Writing back config space on device 0000:02:04.0 at > offset 7 (was 0, writing 54000000) > [ 2.563909] PM: Writing back config space on device 0000:02:04.0 at > offset 6 (was 0, writing b0060302) > [ 2.563915] PM: Writing back config space on device 0000:02:04.0 at > offset 4 (was 0, writing 90100000) > [ 2.563920] PM: Writing back config space on device 0000:02:04.0 at > offset 3 (was 20000, writing 2a820) > [ 2.563926] PM: Writing back config space on device 0000:02:04.0 at > offset 1 (was 2100000, writing 2100007) > [ 2.610134] wbsd 00:02: activated > [ 2.615366] sd 0:0:0:0: [sda] Starting disk > [ 2.661801] ata1.00: configured for UDMA/100 > [ 2.663248] ata1.00: configured for UDMA/100 > [ 2.663251] ata1: EH complete > [ 2.663431] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors > (100030 MB) > [ 2.663443] sd 0:0:0:0: [sda] Write Protect is off > [ 2.663446] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 2.663460] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 2.663474] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors > (100030 MB) > [ 2.663482] sd 0:0:0:0: [sda] Write Protect is off > [ 2.663484] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 2.663497] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > [ 3.344191] Restarting tasks ... <6>usb 3-1: USB disconnect, address 2 > [ 3.360943] done. > [ 3.541329] ipw2200: Radio Frequency Kill Switch is On: > [ 3.541331] Kill switch must be turned off for wireless networking to > work. > [ 3.582665] usb 3-1: new low speed USB device using uhci_hcd and > address 3 > [ 3.737808] usb 3-1: configuration #1 chosen from 1 choice > [ 3.756110] input: PS/2+USB Mouse as /class/input/input7 > [ 3.762983] input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on > usb-0000:00:1d.2-1 > [ 4.837211] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. > [ 4.837232] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode > [ 4.837263] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode > [ 4.837290] [drm] Loading R200 Microcode > [ 5.313446] ata2.00: _GTF unexpected object type 0x1 > [ 5.313453] ata2.00: ACPI on devcfg failed the second time, disabling > (errno=-22) > [ 5.313457] ata2.00: revalidation failed (errno=1) > [ 5.313459] ata2.00: disabled - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
