This is the latest update of the sata_mv conversion to new EH. I'm
looking for testers, of two configurations:
2.6.22 + patch #1 (baseline)
2.6.22 + patch #1 + this patch (sata_mv new EH)
This patch contains a small but key race fix in the interrupt handler,
which should improve things over version 4 of this patch (posted
05/26/2007).
If we are lucky, this will fix the warning messages
WARNING: at drivers/ata/sata_mv.c:1287 mv_qc_issue()
and
WARNING: at drivers/ata/sata_mv.c:1333 mv_get_crpb_status()
but the probability of that happening in reality is below 50%.
I attached a Hitachi NCQ disk to my Gen-II chip, but was unable to
get those WARNINGS to trigger for me, on any kernel. I'll continue to
search for hardware that successfully reproduces the problem. You guys
(Dave, dean) definitely have NCQ disks from different vendors than
me (hopefully I can track down something comparable here at home)
and might have a different chip rev, so I'm not giving up hope of
reproducing it locally yet.
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 3873b29..5a0fe43 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -236,8 +236,10 @@ enum {
EDMA_ERR_DEV_DCON = (1 << 3),
EDMA_ERR_DEV_CON = (1 << 4),
EDMA_ERR_SERR = (1 << 5),
- EDMA_ERR_SELF_DIS = (1 << 7),
+ EDMA_ERR_SELF_DIS = (1 << 7), /* Gen II/IIE self-disable */
+ EDMA_ERR_SELF_DIS_5 = (1 << 8), /* Gen I self-disable */
EDMA_ERR_BIST_ASYNC = (1 << 8),
+ EDMA_ERR_TRANS_IRQ_7 = (1 << 8), /* Gen IIE transprt layer irq */
EDMA_ERR_CRBQ_PAR = (1 << 9),
EDMA_ERR_CRPB_PAR = (1 << 10),
EDMA_ERR_INTRL_PAR = (1 << 11),
@@ -248,13 +250,33 @@ enum {
EDMA_ERR_LNK_CTRL_TX = (0x1f << 21),
EDMA_ERR_LNK_DATA_TX = (0x1f << 26),
EDMA_ERR_TRANS_PROTO = (1 << 31),
- EDMA_ERR_FATAL = (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
- EDMA_ERR_DEV_DCON | EDMA_ERR_CRBQ_PAR |
- EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR |
- EDMA_ERR_IORDY | EDMA_ERR_LNK_CTRL_RX_2 |
- EDMA_ERR_LNK_DATA_RX |
- EDMA_ERR_LNK_DATA_TX |
- EDMA_ERR_TRANS_PROTO),
+ EDMA_ERR_OVERRUN_5 = (1 << 5),
+ EDMA_ERR_UNDERRUN_5 = (1 << 6),
+ EDMA_EH_FREEZE = EDMA_ERR_D_PAR |
+ EDMA_ERR_PRD_PAR |
+ EDMA_ERR_DEV_DCON |
+ EDMA_ERR_DEV_CON |
+ EDMA_ERR_SERR |
+ EDMA_ERR_SELF_DIS |
+ EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_INTRL_PAR |
+ EDMA_ERR_IORDY |
+ EDMA_ERR_LNK_CTRL_RX_2 |
+ EDMA_ERR_LNK_DATA_RX |
+ EDMA_ERR_LNK_DATA_TX |
+ EDMA_ERR_TRANS_PROTO,
+ EDMA_EH_FREEZE_5 = EDMA_ERR_D_PAR |
+ EDMA_ERR_PRD_PAR |
+ EDMA_ERR_DEV_DCON |
+ EDMA_ERR_DEV_CON |
+ EDMA_ERR_OVERRUN_5 |
+ EDMA_ERR_UNDERRUN_5 |
+ EDMA_ERR_SELF_DIS_5 |
+ EDMA_ERR_CRBQ_PAR |
+ EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_INTRL_PAR |
+ EDMA_ERR_IORDY,
EDMA_REQ_Q_BASE_HI_OFS = 0x10,
EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */
@@ -288,6 +310,7 @@ enum {
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0),
MV_PP_FLAG_EDMA_DS_ACT = (1 << 1),
+ MV_PP_FLAG_HAD_A_RESET = (1 << 2),
};
#define IS_50XX(hpriv) ((hpriv)->hp_flags & MV_HP_50XX)
@@ -384,14 +407,14 @@ static u32 mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
static void mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
static u32 mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in);
static void mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val);
-static void mv_phy_reset(struct ata_port *ap);
-static void __mv_phy_reset(struct ata_port *ap, int can_sleep);
static int mv_port_start(struct ata_port *ap);
static void mv_port_stop(struct ata_port *ap);
static void mv_qc_prep(struct ata_queued_cmd *qc);
static void mv_qc_prep_iie(struct ata_queued_cmd *qc);
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc);
-static void mv_eng_timeout(struct ata_port *ap);
+static void mv_error_handler(struct ata_port *ap);
+static void mv_eh_freeze(struct ata_port *ap);
+static void mv_eh_thaw(struct ata_port *ap);
static int mv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio,
@@ -415,7 +438,6 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio);
static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio);
static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
unsigned int port_no);
-static void mv_stop_and_reset(struct ata_port *ap);
static struct scsi_host_template mv_sht = {
.module = THIS_MODULE,
@@ -444,19 +466,20 @@ static const struct ata_port_operations mv5_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = mv_phy_reset,
.cable_detect = ata_cable_sata,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
.data_xfer = ata_data_xfer,
- .eng_timeout = mv_eng_timeout,
-
.irq_clear = mv_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
+ .error_handler = mv_error_handler,
+ .freeze = mv_eh_freeze,
+ .thaw = mv_eh_thaw,
+
.scr_read = mv5_scr_read,
.scr_write = mv5_scr_write,
@@ -473,19 +496,20 @@ static const struct ata_port_operations mv6_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = mv_phy_reset,
.cable_detect = ata_cable_sata,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
.data_xfer = ata_data_xfer,
- .eng_timeout = mv_eng_timeout,
-
.irq_clear = mv_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
+ .error_handler = mv_error_handler,
+ .freeze = mv_eh_freeze,
+ .thaw = mv_eh_thaw,
+
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -502,19 +526,20 @@ static const struct ata_port_operations mv_iie_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = mv_phy_reset,
.cable_detect = ata_cable_sata,
.qc_prep = mv_qc_prep_iie,
.qc_issue = mv_qc_issue,
.data_xfer = ata_data_xfer,
- .eng_timeout = mv_eng_timeout,
-
.irq_clear = mv_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
+ .error_handler = mv_error_handler,
+ .freeze = mv_eh_freeze,
+ .thaw = mv_eh_thaw,
+
.scr_read = mv_scr_read,
.scr_write = mv_scr_write,
@@ -739,12 +764,12 @@ static void mv_start_dma(void __iomem *base, struct mv_port_priv *pp)
* LOCKING:
* Inherited from caller.
*/
-static void mv_stop_dma(struct ata_port *ap)
+static int mv_stop_dma(struct ata_port *ap)
{
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
u32 reg;
- int i;
+ int i, err = 0;
if (MV_PP_FLAG_EDMA_EN & pp->pp_flags) {
/* Disable EDMA if active. The disable bit auto clears.
@@ -764,10 +789,12 @@ static void mv_stop_dma(struct ata_port *ap)
udelay(100);
}
- if (EDMA_EN & reg) {
+ if (reg & EDMA_EN) {
ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n");
- /* FIXME: Consider doing a reset here to recover */
+ err = -EIO;
}
+
+ return err;
}
#ifdef ATA_DEBUG
@@ -1331,30 +1358,95 @@ static u8 mv_get_crpb_status(struct ata_port *ap)
* LOCKING:
* Inherited from caller.
*/
-static void mv_err_intr(struct ata_port *ap, int reset_allowed)
+static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc,
+ unsigned int err_mask)
{
void __iomem *port_mmio = mv_ap_base(ap);
- u32 edma_err_cause, serr = 0;
+ u32 edma_err_cause, eh_freeze_mask, serr = 0;
+ struct mv_port_priv *pp = ap->private_data;
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ unsigned int edma_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN);
+ unsigned int action = 0;
+ struct ata_eh_info *ehi = &ap->eh_info;
- edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+ ata_ehi_clear_desc(ehi);
- if (EDMA_ERR_SERR & edma_err_cause) {
+ if (!edma_enabled) {
+ /* just a guess: do we need to do this? should we
+ * expand this, and do it in all cases?
+ */
sata_scr_read(ap, SCR_ERROR, &serr);
sata_scr_write_flush(ap, SCR_ERROR, serr);
}
- if (EDMA_ERR_SELF_DIS & edma_err_cause) {
- struct mv_port_priv *pp = ap->private_data;
- pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+
+ edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ ata_ehi_push_desc(ehi, "edma_err 0x%08x", edma_err_cause);
+
+ /*
+ * all generations share these EDMA error cause bits
+ */
+
+ if (edma_err_cause & EDMA_ERR_DEV)
+ err_mask |= AC_ERR_DEV;
+ if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR |
+ EDMA_ERR_CRBQ_PAR | EDMA_ERR_CRPB_PAR |
+ EDMA_ERR_INTRL_PAR)) {
+ err_mask |= AC_ERR_ATA_BUS;
+ action |= ATA_EH_HARDRESET;
+ ata_ehi_push_desc(ehi, ", parity error");
+ }
+ if (edma_err_cause & (EDMA_ERR_DEV_DCON | EDMA_ERR_DEV_CON)) {
+ ata_ehi_hotplugged(ehi);
+ ata_ehi_push_desc(ehi, edma_err_cause & EDMA_ERR_DEV_DCON ?
+ ", dev disconnect" : ", dev connect");
+ }
+
+ if (IS_50XX(hpriv)) {
+ eh_freeze_mask = EDMA_EH_FREEZE_5;
+
+ if (edma_err_cause & EDMA_ERR_SELF_DIS_5) {
+ struct mv_port_priv *pp = ap->private_data;
+ pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ ata_ehi_push_desc(ehi, ", EDMA self-disable");
+ }
+ } else {
+ eh_freeze_mask = EDMA_EH_FREEZE;
+
+ if (edma_err_cause & EDMA_ERR_SELF_DIS) {
+ struct mv_port_priv *pp = ap->private_data;
+ pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ ata_ehi_push_desc(ehi, ", EDMA self-disable");
+ }
+
+ if (edma_err_cause & EDMA_ERR_SERR) {
+ sata_scr_read(ap, SCR_ERROR, &serr);
+ sata_scr_write_flush(ap, SCR_ERROR, serr);
+ err_mask = AC_ERR_ATA_BUS;
+ action |= ATA_EH_HARDRESET;
+ }
}
- DPRINTK(KERN_ERR "ata%u: port error; EDMA err cause: 0x%08x "
- "SERR: 0x%08x\n", ap->print_id, edma_err_cause, serr);
/* Clear EDMA now that SERR cleanup done */
writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- /* check for fatal here and recover if needed */
- if (reset_allowed && (EDMA_ERR_FATAL & edma_err_cause))
- mv_stop_and_reset(ap);
+ if (!err_mask) {
+ err_mask = AC_ERR_OTHER;
+ action |= ATA_EH_HARDRESET;
+ }
+
+ ehi->serror |= serr;
+ ehi->action |= action;
+
+ if (qc)
+ qc->err_mask |= err_mask;
+ else
+ ehi->err_mask |= err_mask;
+
+ if (edma_err_cause & eh_freeze_mask)
+ ata_port_freeze(ap);
+ else
+ ata_port_abort(ap);
}
/**
@@ -1389,8 +1481,10 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
/* we'll need the HC success int register in most cases */
hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
- if (hc_irq_cause)
- writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (!hc_irq_cause)
+ return;
+
+ writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n",
hc,relevant,hc_irq_cause);
@@ -1399,9 +1493,11 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
u8 ata_status = 0;
struct ata_port *ap = host->ports[port];
struct mv_port_priv *pp = ap->private_data;
+ int have_err_bits;
hard_port = mv_hardport_from_port(port); /* range 0..3 */
handled = 0; /* ensure ata_status is set if handled++ */
+ err_mask = 0;
/* Note that DEV_IRQ might happen spuriously during EDMA,
* and should be ignored in such cases.
@@ -1429,32 +1525,66 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc)
if (ap && (ap->flags & ATA_FLAG_DISABLED))
continue;
- err_mask = ac_err_mask(ata_status);
+ if (handled)
+ err_mask = ac_err_mask(ata_status);
shift = port << 1; /* (port * 2) */
if (port >= MV_PORTS_PER_HC) {
shift++; /* skip bit 8 in the HC Main IRQ reg */
}
- if ((PORT0_ERR << shift) & relevant) {
- mv_err_intr(ap, 1);
- err_mask |= AC_ERR_OTHER;
- handled = 1;
+ have_err_bits = ((PORT0_ERR << shift) & relevant);
+
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+
+ if ((qc) && (!(qc->tf.flags & ATA_TFLAG_POLLING))) {
+ if (have_err_bits || err_mask)
+ mv_err_intr(ap, qc, err_mask);
+ else
+ ata_qc_complete(qc);
}
+ else if ((!qc) && (have_err_bits || err_mask))
+ mv_err_intr(ap, qc, err_mask);
+ }
+ VPRINTK("EXIT\n");
+}
- if (handled) {
+static void mv_pci_error(struct ata_host *host, void __iomem *mmio)
+{
+ struct ata_port *ap;
+ struct ata_queued_cmd *qc;
+ struct ata_eh_info *ehi;
+ unsigned int i, err_mask, printed = 0;
+ u32 err_cause;
+
+ err_cause = readl(mmio + PCI_IRQ_CAUSE_OFS);
+
+ dev_printk(KERN_ERR, host->dev, "PCI ERROR; PCI IRQ cause=0x%08x\n",
+ err_cause);
+
+ DPRINTK("All regs @ PCI error\n");
+ mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev));
+
+ writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
+
+ for (i = 0; i < host->n_ports; i++) {
+ ap = host->ports[i];
+ if (!ata_port_offline(ap)) {
+ ehi = &ap->eh_info;
+ ata_ehi_clear_desc(ehi);
+ if (!printed++)
+ ata_ehi_push_desc(ehi,
+ "PCI err cause 0x%08x", err_cause);
+ err_mask = AC_ERR_HOST_BUS;
+ ehi->action = ATA_EH_HARDRESET;
qc = ata_qc_from_tag(ap, ap->active_tag);
- if (qc && (qc->flags & ATA_QCFLAG_ACTIVE)) {
- VPRINTK("port %u IRQ found for qc, "
- "ata_status 0x%x\n", port,ata_status);
- /* mark qc status appropriately */
- if (!(qc->tf.flags & ATA_TFLAG_POLLING)) {
- qc->err_mask |= err_mask;
- ata_qc_complete(qc);
- }
- }
+ if (qc)
+ qc->err_mask |= err_mask;
+ else
+ ehi->err_mask |= err_mask;
+
+ ata_port_freeze(ap);
}
}
- VPRINTK("EXIT\n");
}
/**
@@ -1491,17 +1621,27 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
n_hcs = mv_get_hc_count(host->ports[0]->flags);
spin_lock(&host->lock);
+ if (unlikely(irq_stat & PCI_ERR)) {
+ mv_pci_error(host, mmio);
+ handled = 1;
+ goto out_unlock; /* skip all other HC irq handling */
+ }
+
for (hc = 0; hc < n_hcs; hc++) {
u32 relevant = irq_stat & (HC0_IRQ_PEND << (hc * HC_SHIFT));
if (relevant) {
mv_host_intr(host, relevant, hc);
- handled++;
+ handled = 1;
}
}
hpriv = host->private_data;
if (IS_60XX(hpriv)) {
- /* deal with the interrupt coalescing bits */
+ /*
+ * deal with the interrupt coalescing bits; they
+ * are masked via HC_MAIN_MASKED_IRQS, so we shouldn't
+ * need to do this.
+ */
if (irq_stat & (TRAN_LO_DONE | TRAN_HI_DONE | PORTS_0_7_COAL_DONE)) {
writelfl(0, mmio + MV_IRQ_COAL_CAUSE_LO);
writelfl(0, mmio + MV_IRQ_COAL_CAUSE_HI);
@@ -1509,16 +1649,7 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance)
}
}
- if (PCI_ERR & irq_stat) {
- printk(KERN_ERR DRV_NAME ": PCI ERROR; PCI IRQ cause=0x%08x\n",
- readl(mmio + PCI_IRQ_CAUSE_OFS));
-
- DPRINTK("All regs @ PCI error\n");
- mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev));
-
- writelfl(0, mmio + PCI_IRQ_CAUSE_OFS);
- handled++;
- }
+out_unlock:
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
@@ -1927,28 +2058,8 @@ static void mv_channel_reset(struct mv_host_priv *hpriv, void __iomem *mmio,
mdelay(1);
}
-static void mv_stop_and_reset(struct ata_port *ap)
-{
- struct mv_host_priv *hpriv = ap->host->private_data;
- void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
-
- mv_stop_dma(ap);
-
- mv_channel_reset(hpriv, mmio, ap->port_no);
-
- __mv_phy_reset(ap, 0);
-}
-
-static inline void __msleep(unsigned int msec, int can_sleep)
-{
- if (can_sleep)
- msleep(msec);
- else
- mdelay(msec);
-}
-
/**
- * __mv_phy_reset - Perform eDMA reset followed by COMRESET
+ * mv_phy_reset - Perform eDMA reset followed by COMRESET
* @ap: ATA channel to manipulate
*
* Part of this is taken from __sata_phy_reset and modified to
@@ -1958,14 +2069,12 @@ static inline void __msleep(unsigned int msec, int can_sleep)
* Inherited from caller. This is coded to safe to call at
* interrupt level, i.e. it does not sleep.
*/
-static void __mv_phy_reset(struct ata_port *ap, int can_sleep)
+static void mv_phy_reset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
struct mv_port_priv *pp = ap->private_data;
struct mv_host_priv *hpriv = ap->host->private_data;
void __iomem *port_mmio = mv_ap_base(ap);
- struct ata_taskfile tf;
- struct ata_device *dev = &ap->device[0];
- unsigned long timeout;
int retry = 5;
u32 sstatus;
@@ -1978,19 +2087,18 @@ static void __mv_phy_reset(struct ata_port *ap, int can_sleep)
/* Issue COMRESET via SControl */
comreset_retry:
sata_scr_write_flush(ap, SCR_CONTROL, 0x301);
- __msleep(1, can_sleep);
+ msleep(1);
sata_scr_write_flush(ap, SCR_CONTROL, 0x300);
- __msleep(20, can_sleep);
+ msleep(20);
- timeout = jiffies + msecs_to_jiffies(200);
do {
sata_scr_read(ap, SCR_STATUS, &sstatus);
if (((sstatus & 0x3) == 3) || ((sstatus & 0x3) == 0))
break;
- __msleep(1, can_sleep);
- } while (time_before(jiffies, timeout));
+ msleep(1);
+ } while (time_before(jiffies, deadline));
/* work around errata */
if (IS_60XX(hpriv) &&
@@ -2002,13 +2110,8 @@ comreset_retry:
"SCtrl 0x%08x\n", mv_scr_read(ap, SCR_STATUS),
mv_scr_read(ap, SCR_ERROR), mv_scr_read(ap, SCR_CONTROL));
- if (ata_port_online(ap)) {
- ata_port_probe(ap);
- } else {
- sata_scr_read(ap, SCR_STATUS, &sstatus);
- ata_port_printk(ap, KERN_INFO,
- "no device found (phy stat %08x)\n", sstatus);
- ata_port_disable(ap);
+ if (ata_port_offline(ap)) {
+ *class = ATA_DEV_NONE;
return;
}
@@ -2022,68 +2125,147 @@ comreset_retry:
u8 drv_stat = ata_check_status(ap);
if ((drv_stat != 0x80) && (drv_stat != 0x7f))
break;
- __msleep(500, can_sleep);
+ msleep(500);
if (retry-- <= 0)
break;
+ if (time_after(jiffies, deadline))
+ break;
}
- tf.lbah = readb(ap->ioaddr.lbah_addr);
- tf.lbam = readb(ap->ioaddr.lbam_addr);
- tf.lbal = readb(ap->ioaddr.lbal_addr);
- tf.nsect = readb(ap->ioaddr.nsect_addr);
+ /* FIXME: if we passed the deadline, the following
+ * code probably produces an invalid result
+ */
- dev->class = ata_dev_classify(&tf);
- if (!ata_dev_enabled(dev)) {
- VPRINTK("Port disabled post-sig: No device present.\n");
- ata_port_disable(ap);
- }
+ /* finally, read device signature from TF registers */
+ *class = ata_dev_try_classify(ap, 0, NULL);
writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ WARN_ON(pp->pp_flags & MV_PP_FLAG_EDMA_EN);
VPRINTK("EXIT\n");
}
-static void mv_phy_reset(struct ata_port *ap)
+static int mv_prereset(struct ata_port *ap, unsigned long deadline)
{
- __mv_phy_reset(ap, 1);
+ struct mv_port_priv *pp = ap->private_data;
+ struct ata_eh_context *ehc = &ap->eh_context;
+ int rc;
+
+ rc = mv_stop_dma(ap);
+ if (rc)
+ ehc->i.action |= ATA_EH_HARDRESET;
+
+ if (!(pp->pp_flags & MV_PP_FLAG_HAD_A_RESET)) {
+ pp->pp_flags |= MV_PP_FLAG_HAD_A_RESET;
+ ehc->i.action |= ATA_EH_HARDRESET;
+ }
+
+ /* if we're about to do hardreset, nothing more to do */
+ if (ehc->i.action & ATA_EH_HARDRESET)
+ return 0;
+
+ if (ata_port_online(ap))
+ rc = ata_wait_ready(ap, deadline);
+ else
+ rc = -ENODEV;
+
+ return rc;
}
-/**
- * mv_eng_timeout - Routine called by libata when SCSI times out I/O
- * @ap: ATA channel to manipulate
- *
- * Intent is to clear all pending error conditions, reset the
- * chip/bus, fail the command, and move on.
- *
- * LOCKING:
- * This routine holds the host lock while failing the command.
- */
-static void mv_eng_timeout(struct ata_port *ap)
+static int mv_hardreset(struct ata_port *ap, unsigned int *class,
+ unsigned long deadline)
{
+ struct mv_host_priv *hpriv = ap->host->private_data;
void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
- struct ata_queued_cmd *qc;
- unsigned long flags;
- ata_port_printk(ap, KERN_ERR, "Entering mv_eng_timeout\n");
- DPRINTK("All regs @ start of eng_timeout\n");
- mv_dump_all_regs(mmio, ap->port_no, to_pci_dev(ap->host->dev));
+ mv_stop_dma(ap);
- qc = ata_qc_from_tag(ap, ap->active_tag);
- printk(KERN_ERR "mmio_base %p ap %p qc %p scsi_cmnd %p &cmnd %p\n",
- mmio, ap, qc, qc->scsicmd, &qc->scsicmd->cmnd);
+ mv_channel_reset(hpriv, mmio, ap->port_no);
- spin_lock_irqsave(&ap->host->lock, flags);
- mv_err_intr(ap, 0);
- mv_stop_and_reset(ap);
- spin_unlock_irqrestore(&ap->host->lock, flags);
+ mv_phy_reset(ap, class, deadline);
- WARN_ON(!(qc->flags & ATA_QCFLAG_ACTIVE));
- if (qc->flags & ATA_QCFLAG_ACTIVE) {
- qc->err_mask |= AC_ERR_TIMEOUT;
- ata_eh_qc_complete(qc);
+ return 0;
+}
+
+static void mv_postreset(struct ata_port *ap, unsigned int *classes)
+{
+ u32 serr;
+
+ /* print link status */
+ sata_print_link_status(ap);
+
+ /* clear SError */
+ sata_scr_read(ap, SCR_ERROR, &serr);
+ sata_scr_write_flush(ap, SCR_ERROR, serr);
+
+ /* bail out if no device is present */
+ if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
+ DPRINTK("EXIT, no device\n");
+ return;
+ }
+
+ /* set up device control */
+ iowrite8(ap->ctl, ap->ioaddr.ctl_addr);
+}
+
+static void mv_error_handler(struct ata_port *ap)
+{
+ ata_do_eh(ap, mv_prereset, ata_std_softreset,
+ mv_hardreset, mv_postreset);
+}
+
+static void mv_eh_freeze(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ unsigned int hc = (ap->port_no > 3) ? 1 : 0;
+ u32 tmp, mask;
+ unsigned int shift;
+
+ /* FIXME: handle coalescing completion events properly */
+
+ shift = ap->port_no * 2;
+ if (hc > 0)
+ shift++;
+
+ mask = 0x3 << shift;
+
+ /* disable assertion of portN err, done events */
+ tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
+ writelfl(tmp & ~mask, mmio + HC_MAIN_IRQ_MASK_OFS);
+}
+
+static void mv_eh_thaw(struct ata_port *ap)
+{
+ void __iomem *mmio = ap->host->iomap[MV_PRIMARY_BAR];
+ unsigned int hc = (ap->port_no > 3) ? 1 : 0;
+ void __iomem *hc_mmio = mv_hc_base(mmio, hc);
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 tmp, mask, hc_irq_cause;
+ unsigned int shift, hc_port_no = ap->port_no;
+
+ /* FIXME: handle coalescing completion events properly */
+
+ shift = ap->port_no * 2;
+ if (hc > 0) {
+ shift++;
+ hc_port_no -= 4;
}
+
+ mask = 0x3 << shift;
+
+ /* clear EDMA errors on this port */
+ writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ /* clear pending irq events */
+ hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS);
+ hc_irq_cause &= ~(1 << hc_port_no); /* clear CRPB-done */
+ hc_irq_cause &= ~(1 << (hc_port_no + 8)); /* clear Device int */
+ writel(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+
+ /* enable assertion of portN err, done events */
+ tmp = readl(mmio + HC_MAIN_IRQ_MASK_OFS);
+ writelfl(tmp | mask, mmio + HC_MAIN_IRQ_MASK_OFS);
}
/**
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
