Can you try with kernel parameter 'acpi=noirq' or 'irqpoll'?
I made a typo when passing the irqpoll parameter to the kernel. In
kernel 2.6.20.4 with the irqpoll parameter passewd to kernel the SATA
disk works:
[ 1.320000] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 1.320000] ahci 0000:00:12.0: version 2.0
[ 1.320000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level,
low) -> IRQ 16
[ 2.324000] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps
0xf impl SATA mode
[ 2.324000] ahci 0000:00:12.0: flags: 64bit ncq ilck pm led clo pmp
pio slum part
[ 2.324000] ata1: SATA max UDMA/133 cmd 0xF8824D00 ctl 0x0 bmdma 0x0
irq 222
[ 2.324000] ata2: SATA max UDMA/133 cmd 0xF8824D80 ctl 0x0 bmdma 0x0
irq 222
[ 2.324000] ata3: SATA max UDMA/133 cmd 0xF8824E00 ctl 0x0 bmdma 0x0
irq 222
[ 2.324000] ata4: SATA max UDMA/133 cmd 0xF8824E80 ctl 0x0 bmdma 0x0
irq 222
[ 2.324000] scsi0 : ahci
[ 2.636000] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.636000] scsi1 : ahci
[ 3.120000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.136000] ata2.00: ATA-7, max UDMA/133, 160836480 sectors: LBA48
NCQ (depth 31/32)
[ 3.136000] ata2.00: ata2: dev 0 multi count 16
[ 3.144000] ata2.00: configured for UDMA/133
[ 3.144000] scsi2 : ahci
[ 3.456000] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.456000] scsi3 : ahci
[ 3.768000] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.768000] scsi 1:0:0:0: Direct-Access ATA HDS728080PLA380
PF2O PQ: 0 ANSI: 5
[ 3.768000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at
0x60,0x64 irq 1,12
[ 3.768000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.768000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.768000] mice: PS/2 mouse device common for all mice
[ 3.768000] EISA: Probing bus 0 at eisa.0
[ 3.768000] EISA: Detected 0 cards.
[ 3.792000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 3.800000] TCP cubic registered
[ 3.800000] NET: Registered protocol family 1
[ 3.800000] Starting balanced_irq
[ 3.800000] Using IPI No-Shortcut mode
[ 3.800000] ACPI: (supports S0 S1 S3 S4 S5)
[ 3.800000] Freeing unused kernel memory: 316k freed
[ 3.804000] Time: hpet clocksource has been installed.
[ 3.876000] ACPI: duty_cycle spans bit 4
[ 4.268000] SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
[ 4.268000] sda: Write Protect is off
[ 4.268000] sda: Mode Sense: 00 3a 00 00
[ 4.268000] SCSI device sda: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.268000] SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
[ 4.268000] sda: Write Protect is off
[ 4.268000] sda: Mode Sense: 00 3a 00 00
[ 4.268000] SCSI device sda: write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.268000] sda: sda1
[ 4.292000] sd 1:0:0:0: Attached scsi disk sda
And the disk (lshw):
*-storage
description: SATA controller
product: SB600 Non-Raid-5 SATA
vendor: ATI Technologies Inc
physical id: 12
bus info: pci@00:12.0
logical name: scsi1
version: 00
width: 32 bits
clock: 66MHz
capabilities: storage ahci_1.0 bus_master cap_list emulated
configuration: driver=ahci
resources: ioport:e800-e807 ioport:e400-e403
ioport:e000-e007 ioport:dc00-dc03 ioport:d800-d80f
iomemory:febffc00-febfffff irq:222
*-disk
description: SCSI Disk
product: HDS728080PLA380
vendor: ATA
physical id: 0.0.0
bus info: scsi@1:0.0.0
logical name: /dev/sda
version: PF2O
serial: PFDH37SYTWKR9E
size: 76GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
Nice isn't it? I'm happy.
In the 2.6.21-rc5 version this hasn't worked (the typo was here too,
copy, paste & destroy :P). Here's is the output of dmesg:
[ 1.336000] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 1.340000] ahci 0000:00:12.0: version 2.1
[ 1.340000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level,
low) -> IRQ 16
[ 2.344000] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps
0xf impl SATA mode
[ 2.344000] ahci 0000:00:12.0: flags: 64bit ncq ilck pm led clo pmp
pio slum part
[ 2.344000] ata1: SATA max UDMA/133 cmd 0xf8824d00 ctl 0x00000000
bmdma 0x00000000 irq 222
[ 2.344000] ata2: SATA max UDMA/133 cmd 0xf8824d80 ctl 0x00000000
bmdma 0x00000000 irq 222
[ 2.344000] ata3: SATA max UDMA/133 cmd 0xf8824e00 ctl 0x00000000
bmdma 0x00000000 irq 222
[ 2.344000] ata4: SATA max UDMA/133 cmd 0xf8824e80 ctl 0x00000000
bmdma 0x00000000 irq 222
[ 2.344000] scsi0 : ahci
[ 2.656000] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.656000] scsi1 : ahci
[ 3.140000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.140000] ata2.00: qc timeout (cmd 0xec)
[ 33.140000] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 34.120000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 64.120000] ata2.00: qc timeout (cmd 0xec)
[ 64.120000] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 64.120000] ata2.00: limiting speed to UDMA7:PIO5
[ 65.100000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 95.100000] ata2.00: qc timeout (cmd 0xec)
[ 95.100000] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 96.080000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 96.080000] scsi2 : ahci
[ 96.392000] ata3: SATA link down (SStatus 0 SControl 300)
[ 96.392000] scsi3 : ahci
[ 96.704000] ata4: SATA link down (SStatus 0 SControl 300)
[ 96.704000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at
0x60,0x64 irq 1,12
[ 96.704000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 96.704000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 96.704000] mice: PS/2 mouse device common for all mice
[ 96.704000] EISA: Probing bus 0 at eisa.0
[ 96.704000] EISA: Detected 0 cards.
[ 96.704000] TCP cubic registered
[ 96.704000] NET: Registered protocol family 1
[ 96.704000] Starting balanced_irq
[ 96.704000] Using IPI No-Shortcut mode
[ 96.708000] Freeing unused kernel memory: 332k freed
[ 96.724000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 96.780000] ACPI: duty_cycle spans bit 4
[ 97.236000] SB600_PATA: IDE controller at PCI slot 0000:00:14.1
[ 97.240000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level,
low) -> IRQ 17
[ 97.240000] SB600_PATA: chipset revision 0
[ 97.240000] SB600_PATA: not 100% native mode: will probe irqs later
[ 97.240000] ide0: BM-DMA at 0xff00-0xff07, BIOS settings:
hda:DMA, hdb:DMA
[ 97.240000] Probing IDE interface ide0...
[ 97.528000] hda: HDS728080PLAT20, ATA DISK drive
[ 97.976000] hdb: ASUS DRW-1608P3S, ATAPI CD/DVD-ROM drive
[ 98.032000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 98.052000] hda: max request size: 512KiB
[ 98.056000] hda: 160836480 sectors (82348 MB) w/1719KiB Cache,
CHS=16383/255/63, UDMA(100)
[ 98.056000] hda: cache flushes supported
[ 98.056000] hda: hda1 hda2 < hda5 hda6 >
[ 98.108000] hdb: ATAPI 63X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB
Cache, UDMA(66)
[ 98.108000] Uniform CD-ROM driver Revision: 3.20
[ 98.356000] Probing IDE interface ide1...
Why this happens? Any clue?
I attached those files too so you can take a better look at them. Thanks!
Matías
[ 0.000000] Linux version 2.6.20.4 (root@matias) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #1 SMP Sat Mar 24 13:19:32 ART 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fec0000 end: 000000003ffc0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000003ffc0000 size: 000000000000e000 end: 000000003ffce000 type: 3
[ 0.000000] copy_e820_map() start: 000000003ffce000 size: 0000000000032000 end: 0000000040000000 type: 4
[ 0.000000] copy_e820_map() start: 00000000ff780000 size: 0000000000880000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
[ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ffce000 - 0000000040000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 262080) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262080
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262080
[ 0.000000] On node 0 totalpages: 262080
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32449 pages, LIFO batch:7
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 ACPIAM ) @ 0x000f84e0
[ 0.000000] ACPI: RSDT (v001 A M I OEMRSDT 0x07000604 MSFT 0x00000097) @ 0x3ffc0000
[ 0.000000] ACPI: FADT (v002 A M I OEMFACP 0x07000604 MSFT 0x00000097) @ 0x3ffc0200
[ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x07000604 MSFT 0x00000097) @ 0x3ffc0390
[ 0.000000] ACPI: MCFG (v001 A M I OEMMCFG 0x07000604 MSFT 0x00000097) @ 0x3ffc03f0
[ 0.000000] ACPI: WDRT (v001 A M I OEMWDRT 0x07000604 MSFT 0x00000097) @ 0x3ffc0430
[ 0.000000] ACPI: OEMB (v001 A M I AMI_OEM 0x07000604 MSFT 0x00000097) @ 0x3ffce040
[ 0.000000] ACPI: HPET (v001 A M I OEMHPET 0x07000604 MSFT 0x00000097) @ 0x3ffc4250
[ 0.000000] ACPI: SSDT (v001 A M I ACPI2PPC 0x00000001 AMI 0x00000001) @ 0x3ffc4290
[ 0.000000] ACPI: DSDT (v001 AMMR_ AMMR_B36 0x00000b36 INTL 0x20051117) @ 0x00000000
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:11 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:11 APIC version 16
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8000 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
[ 0.000000] Detected 2000.179 MHz processor.
[ 22.317443] Built 1 zonelists. Total pages: 260033
[ 22.317446] Kernel command line: root=/dev/hda5 ro irqpoll
[ 22.317459] Misrouted IRQ fixup and polling support enabled
[ 22.317461] This may significantly impact system performance
[ 22.317571] mapped APIC to ffffd000 (fee00000)
[ 22.317574] mapped IOAPIC to ffffc000 (fec00000)
[ 22.317576] Enabling fast FPU save and restore... done.
[ 22.317579] Enabling unmasked SIMD FPU exception support... done.
[ 22.317586] Initializing CPU#0
[ 22.317638] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 22.319942] Console: colour VGA+ 80x25
[ 22.323228] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 22.324041] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 22.344370] Memory: 1029668k/1048320k available (2078k kernel code, 17936k reserved, 958k data, 316k init, 130816k highmem)
[ 22.344452] virtual kernel memory layout:
[ 22.344453] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 22.344454] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 22.344456] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 22.344457] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 22.344458] .init : 0xc03fe000 - 0xc044d000 ( 316 kB)
[ 22.344459] .data : 0xc0307bb4 - 0xc03f76f4 ( 958 kB)
[ 22.344460] .text : 0xc0100000 - 0xc0307bb4 (2078 kB)
[ 22.344905] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 22.345149] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 22.345408] hpet0: 4 32-bit timers, 14318180 Hz
[ 22.346467] Using HPET for base-timer
[ 22.425010] Calibrating delay using timer specific routine.. 4009.85 BogoMIPS (lpj=8019714)
[ 22.425158] Security Framework v1.0.0 initialized
[ 22.425219] SELinux: Disabled at boot.
[ 22.425285] Mount-cache hash table entries: 512
[ 22.425462] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 22.425470] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 22.425529] CPU: L2 Cache: 256K (64 bytes/line)
[ 22.425586] CPU 0(2) -> Core 0
[ 22.425640] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 22.425649] Compat vDSO mapped to ffffe000.
[ 22.425712] Checking 'hlt' instruction... OK.
[ 22.441159] SMP alternatives: switching to UP code
[ 22.441408] ACPI: Core revision 20060707
[ 22.444005] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
[ 22.444165] SMP alternatives: switching to SMP code
[ 22.444338] Booting processor 1/1 eip 3000
[ 22.454283] Initializing CPU#1
[ 22.532516] Calibrating delay using timer specific routine.. 4000.22 BogoMIPS (lpj=8000442)
[ 22.532523] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 22.532529] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 22.532531] CPU: L2 Cache: 256K (64 bytes/line)
[ 22.532533] CPU 1(2) -> Core 1
[ 22.532534] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 22.532881] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
[ 22.533317] Total of 2 processors activated (8010.07 BogoMIPS).
[ 22.533516] ENABLING IO-APIC IRQs
[ 22.533737] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 22.680517] checking TSC synchronization across 2 CPUs:
[ 0.000051] CPU#0 had 136 usecs TSC skew, fixed it up.
[ 0.000107] CPU#1 had -136 usecs TSC skew, fixed it up.
[ 0.003947] Brought up 2 CPUs
[ 0.044808] migration_cost=140
[ 0.045232] NET: Registered protocol family 16
[ 0.045366] EISA bus registered
[ 0.045422] ACPI: bus type pci registered
[ 0.045485] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
[ 0.045543] PCI: Not using MMCONFIG.
[ 0.046366] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.046424] PCI: Using configuration type 1
[ 0.046480] Setting up standard PCI resources
[ 0.087854] ACPI: Interpreter enabled
[ 0.087914] ACPI: Using IOAPIC for interrupt routing
[ 0.088279] Error attaching device data
[ 0.088338] Error attaching device data
[ 0.088505] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.088563] PCI: Probing PCI hardware (bus 00)
[ 0.090772] 0000:00:14.1: trying to change BAR0 from 0000 to 01F0
[ 0.090832] 0000:00:14.1: trying to change BAR1 from 0000 to 03F4
[ 0.090891] 0000:00:14.1: trying to change BAR2 from 0000 to 0170
[ 0.090951] 0000:00:14.1: trying to change BAR3 from 0000 to 0374
[ 0.091286] Boot video device is 0000:01:00.0
[ 0.091482] PCI: Transparent bridge - 0000:00:14.4
[ 0.091565] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.114083] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[ 0.116956] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
[ 0.118242] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.119028] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.119818] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.120598] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.121380] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.122161] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[ 0.122609] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.123390] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.124123] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.124188] pnp: PnP ACPI init
[ 0.128327] pnp: PnP ACPI: found 17 devices
[ 0.128388] PnPBIOS: Disabled by ACPI PNP
[ 0.128575] SCSI subsystem initialized
[ 0.128663] libata version 2.00 loaded.
[ 0.128693] PCI: Using ACPI for IRQ routing
[ 0.128750] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.137872] NET: Registered protocol family 8
[ 0.137928] NET: Registered protocol family 20
[ 0.138863] pnp: 00:0e: ioport range 0xa00-0xa0f has been reserved
[ 0.138922] pnp: 00:0e: ioport range 0x600-0x60f has been reserved
[ 0.139192] PCI: Bridge: 0000:00:02.0
[ 0.139247] IO window: disabled.
[ 0.139304] MEM window: fa900000-fe9fffff
[ 0.139361] PREFETCH window: bff00000-dfefffff
[ 0.139419] PCI: Bridge: 0000:00:14.4
[ 0.139475] IO window: b000-bfff
[ 0.139533] MEM window: fea00000-feafffff
[ 0.139591] PREFETCH window: 50000000-500fffff
[ 0.139661] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.139714] NET: Registered protocol family 2
[ 0.175689] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.175896] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.177008] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.177578] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.177639] TCP reno registered
[ 0.187722] checking if image is initramfs... it is
[ 0.602396] Freeing initrd memory: 5076k freed
[ 0.840000] audit: initializing netlink socket (disabled)
[ 0.840000] audit(1174956175.024:1): initialized
[ 0.840000] highmem bounce pool size: 64 pages
[ 0.840000] VFS: Disk quotas dquot_6.5.1
[ 0.840000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.840000] io scheduler noop registered
[ 0.840000] io scheduler anticipatory registered
[ 0.840000] io scheduler deadline registered
[ 0.840000] io scheduler cfq registered (default)
[ 0.940000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.940000] assign_interrupt_mode Found MSI capability
[ 0.940000] Allocate Port Service[0000:00:02.0:pcie00]
[ 0.940000] isapnp: Scanning for PnP cards...
[ 1.292000] isapnp: No Plug & Play device found
[ 1.320000] Real Time Clock Driver v1.12ac
[ 1.320000] hpet_resources: 0xfed00000 is busy
[ 1.320000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.320000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.320000] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.320000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.320000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1.320000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1.320000] ahci 0000:00:12.0: version 2.0
[ 1.320000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 16
[ 2.324000] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 2.324000] ahci 0000:00:12.0: flags: 64bit ncq ilck pm led clo pmp pio slum part
[ 2.324000] ata1: SATA max UDMA/133 cmd 0xF8824D00 ctl 0x0 bmdma 0x0 irq 222
[ 2.324000] ata2: SATA max UDMA/133 cmd 0xF8824D80 ctl 0x0 bmdma 0x0 irq 222
[ 2.324000] ata3: SATA max UDMA/133 cmd 0xF8824E00 ctl 0x0 bmdma 0x0 irq 222
[ 2.324000] ata4: SATA max UDMA/133 cmd 0xF8824E80 ctl 0x0 bmdma 0x0 irq 222
[ 2.324000] scsi0 : ahci
[ 2.636000] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.636000] scsi1 : ahci
[ 3.120000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.136000] ata2.00: ATA-7, max UDMA/133, 160836480 sectors: LBA48 NCQ (depth 31/32)
[ 3.136000] ata2.00: ata2: dev 0 multi count 16
[ 3.144000] ata2.00: configured for UDMA/133
[ 3.144000] scsi2 : ahci
[ 3.456000] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.456000] scsi3 : ahci
[ 3.768000] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.768000] scsi 1:0:0:0: Direct-Access ATA HDS728080PLA380 PF2O PQ: 0 ANSI: 5
[ 3.768000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 3.768000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.768000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.768000] mice: PS/2 mouse device common for all mice
[ 3.768000] EISA: Probing bus 0 at eisa.0
[ 3.768000] EISA: Detected 0 cards.
[ 3.792000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 3.800000] TCP cubic registered
[ 3.800000] NET: Registered protocol family 1
[ 3.800000] Starting balanced_irq
[ 3.800000] Using IPI No-Shortcut mode
[ 3.800000] ACPI: (supports S0 S1 S3 S4 S5)
[ 3.800000] Freeing unused kernel memory: 316k freed
[ 3.804000] Time: hpet clocksource has been installed.
[ 3.876000] ACPI: duty_cycle spans bit 4
[ 4.268000] SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
[ 4.268000] sda: Write Protect is off
[ 4.268000] sda: Mode Sense: 00 3a 00 00
[ 4.268000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.268000] SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
[ 4.268000] sda: Write Protect is off
[ 4.268000] sda: Mode Sense: 00 3a 00 00
[ 4.268000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.268000] sda: sda1
[ 4.292000] sd 1:0:0:0: Attached scsi disk sda
[ 4.516000] SB600_PATA: IDE controller at PCI slot 0000:00:14.1
[ 4.516000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
[ 4.516000] SB600_PATA: chipset revision 0
[ 4.520000] SB600_PATA: not 100% native mode: will probe irqs later
[ 4.520000] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[ 4.520000] Probing IDE interface ide0...
[ 4.808000] hda: HDS728080PLAT20, ATA DISK drive
[ 5.256000] hdb: ASUS DRW-1608P3S, ATAPI CD/DVD-ROM drive
[ 5.312000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.316000] hda: max request size: 512KiB
[ 5.328000] hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(33)
[ 5.328000] hda: cache flushes supported
[ 5.328000] hda: hda1 hda2 < hda5 hda6 >
[ 5.388000] hdb: ATAPI 63X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache, UDMA(66)
[ 5.392000] Uniform CD-ROM driver Revision: 3.20
[ 5.692000] Probing IDE interface ide1...
[ 5.724000] usbcore: registered new interface driver usbfs
[ 5.724000] usbcore: registered new interface driver hub
[ 5.724000] usbcore: registered new device driver usb
[ 5.724000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 5.724000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 5.724000] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 5.724000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 5.724000] ohci_hcd 0000:00:13.0: irq 17, io mem 0xfebfe000
[ 5.784000] usb usb1: configuration #1 chosen from 1 choice
[ 5.784000] hub 1-0:1.0: USB hub found
[ 5.784000] hub 1-0:1.0: 2 ports detected
[ 5.888000] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 18
[ 5.888000] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 5.888000] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 2
[ 5.888000] ehci_hcd 0000:00:13.5: debug port 1
[ 5.888000] ehci_hcd 0000:00:13.5: irq 18, io mem 0xfebff800
[ 5.888000] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 5.888000] usb usb2: configuration #1 chosen from 1 choice
[ 5.888000] hub 2-0:1.0: USB hub found
[ 5.888000] hub 2-0:1.0: 10 ports detected
[ 5.992000] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 19
[ 5.992000] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 5.992000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[ 5.992000] ohci_hcd 0000:00:13.1: irq 19, io mem 0xfebfd000
[ 6.052000] usb usb3: configuration #1 chosen from 1 choice
[ 6.052000] hub 3-0:1.0: USB hub found
[ 6.052000] hub 3-0:1.0: 2 ports detected
[ 6.156000] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 20
[ 6.156000] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 6.156000] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
[ 6.156000] ohci_hcd 0000:00:13.2: irq 20, io mem 0xfebfc000
[ 6.216000] usb usb4: configuration #1 chosen from 1 choice
[ 6.216000] hub 4-0:1.0: USB hub found
[ 6.216000] hub 4-0:1.0: 2 ports detected
[ 6.320000] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 19
[ 6.320000] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 6.320000] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
[ 6.320000] ohci_hcd 0000:00:13.3: irq 19, io mem 0xfebfb000
[ 6.380000] usb usb5: configuration #1 chosen from 1 choice
[ 6.380000] hub 5-0:1.0: USB hub found
[ 6.380000] hub 5-0:1.0: 2 ports detected
[ 6.484000] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 20
[ 6.484000] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 6.484000] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
[ 6.484000] ohci_hcd 0000:00:13.4: irq 20, io mem 0xfebfa000
[ 6.544000] usb usb6: configuration #1 chosen from 1 choice
[ 6.544000] hub 6-0:1.0: USB hub found
[ 6.544000] hub 6-0:1.0: 2 ports detected
[ 6.716000] Attempting manual resume
[ 6.736000] kjournald starting. Commit interval 5 seconds
[ 6.736000] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.968000] Floppy drive(s): fd0 is 1.44M
[ 16.984000] FDC 0 is a post-1991 82077
[ 17.328000] input: PC Speaker as /class/input/input1
[ 17.884000] Linux agpgart interface v0.101 (c) Dave Jones
[ 17.900000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 17.904000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 17.952000] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 17.988000] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 17.988000] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 17.988000] eth0: RTL8169sc/8110sc at 0xf8896800, 00:16:17:c3:b8:f9, IRQ 21
[ 18.036000] parport: PnPBIOS parport detected.
[ 18.036000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 18.112000] r8169: eth0: link down
[ 18.236000] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
[ 18.436000] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 18.656000] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[ 18.728000] lp0: using parport0 (interrupt-driven).
[ 18.856000] Adding 1052216k swap on /dev/disk/by-uuid/ba363ce4-0f51-4ff4-abdb-c02e7467cc43. Priority:-1 extents:1 across:1052216k
[ 18.980000] EXT3 FS on hda5, internal journal
[ 19.200000] NET: Registered protocol family 17
[ 19.380000] NTFS driver 2.1.28 [Flags: R/O MODULE].
[ 19.576000] r8169: eth0: link up
[ 19.728000] NTFS volume version 3.1.
[ 22.372000] input: Power Button (FF) as /class/input/input3
[ 22.372000] ACPI: Power Button (FF) [PWRF]
[ 22.376000] input: Power Button (CM) as /class/input/input4
[ 22.376000] ACPI: Power Button (CM) [PWRB]
[ 22.404000] Using specific hotkey driver
[ 22.468000] No dock devices found.
[ 22.508000] ibm_acpi: ec object not found
[ 22.576000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 22.888000] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ processors (version 2.00.00)
[ 22.888000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0xe
[ 22.888000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x10
[ 22.888000] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
[ 26.448000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 26.448000] apm: disabled - APM is not SMP safe.
[ 27.332000] NET: Registered protocol family 10
[ 27.332000] lo: Disabled Privacy Extensions
[ 32.412000] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 32.872000] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 33.008000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 33.012000] NFSD: starting 90-second grace period
[ 37.488000] eth0: no IPv6 routers present
[ 0.000000] Linux version 2.6.21-rc5 (root@matias) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #1 SMP Sun Mar 25 23:25:22 ART 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fec0000 end: 000000003ffc0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000003ffc0000 size: 000000000000e000 end: 000000003ffce000 type: 3
[ 0.000000] copy_e820_map() start: 000000003ffce000 size: 0000000000032000 end: 0000000040000000 type: 4
[ 0.000000] copy_e820_map() start: 00000000ff780000 size: 0000000000880000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
[ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ffce000 - 0000000040000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 262080) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262080
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262080
[ 0.000000] On node 0 totalpages: 262080
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32449 pages, LIFO batch:7
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F84E0, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 3FFC0000, 0040 (r1 A M I OEMRSDT 7000604 MSFT 97)
[ 0.000000] ACPI: FACP 3FFC0200, 0084 (r2 A M I OEMFACP 7000604 MSFT 97)
[ 0.000000] ACPI: DSDT 3FFC0480, 3DC9 (r1 AMMR_ AMMR_B36 B36 INTL 20051117)
[ 0.000000] ACPI: FACS 3FFCE000, 0040
[ 0.000000] ACPI: APIC 3FFC0390, 005C (r1 A M I OEMAPIC 7000604 MSFT 97)
[ 0.000000] ACPI: MCFG 3FFC03F0, 003C (r1 A M I OEMMCFG 7000604 MSFT 97)
[ 0.000000] ACPI: WDRT 3FFC0430, 0047 (r1 A M I OEMWDRT 7000604 MSFT 97)
[ 0.000000] ACPI: OEMB 3FFCE040, 0060 (r1 A M I AMI_OEM 7000604 MSFT 97)
[ 0.000000] ACPI: HPET 3FFC4250, 0038 (r1 A M I OEMHPET 7000604 MSFT 97)
[ 0.000000] ACPI: SSDT 3FFC4290, 01C4 (r1 A M I ACPI2PPC 1 AMI 1)
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:11 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:11 APIC version 16
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8000 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000)
[ 0.000000] Built 1 zonelists. Total pages: 260033
[ 0.000000] Kernel command line: root=/dev/hda5 ro irqpoll
[ 0.000000] Misrouted IRQ fixup and polling support enabled
[ 0.000000] This may significantly impact system performance
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2000.238 MHz processor.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1029748k/1048320k available (2099k kernel code, 17928k reserved, 970k data, 332k init, 130816k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000000] .init : 0xc0406000 - 0xc0459000 ( 332 kB)
[ 0.000000] .data : 0xc030cc9c - 0xc03ff754 ( 970 kB)
[ 0.000000] .text : 0xc0100000 - 0xc030cc9c (2099 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 0.000000] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.000000] hpet0: 4 32-bit timers, 14318180 Hz
[ 0.084000] Calibrating delay using timer specific routine.. 4009.58 BogoMIPS (lpj=8019165)
[ 0.084000] Security Framework v1.0.0 initialized
[ 0.084000] SELinux: Disabled at boot.
[ 0.084000] Mount-cache hash table entries: 512
[ 0.084000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.084000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.084000] CPU: L2 Cache: 256K (64 bytes/line)
[ 0.084000] CPU 0(2) -> Core 0
[ 0.084000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.084000] Compat vDSO mapped to ffffe000.
[ 0.084000] Checking 'hlt' instruction... OK.
[ 0.100000] SMP alternatives: switching to UP code
[ 0.100000] ACPI: Core revision 20070126
[ 0.100000] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
[ 0.100000] SMP alternatives: switching to SMP code
[ 0.100000] Booting processor 1/1 eip 3000
[ 0.112000] Initializing CPU#1
[ 0.192000] Calibrating delay using timer specific routine.. 4000.15 BogoMIPS (lpj=8000314)
[ 0.192000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.192000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.192000] CPU: L2 Cache: 256K (64 bytes/line)
[ 0.192000] CPU 1(2) -> Core 1
[ 0.192000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.192000] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
[ 0.192000] Total of 2 processors activated (8009.73 BogoMIPS).
[ 0.192000] ENABLING IO-APIC IRQs
[ 0.192000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.232000] Brought up 2 CPUs
[ 0.272000] migration_cost=4000
[ 0.272000] NET: Registered protocol family 16
[ 0.272000] EISA bus registered
[ 0.272000] ACPI: bus type pci registered
[ 0.272000] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
[ 0.272000] PCI: Not using MMCONFIG.
[ 0.272000] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.272000] PCI: Using configuration type 1
[ 0.272000] Setting up standard PCI resources
[ 0.316000] ACPI: Interpreter enabled
[ 0.316000] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.316000] ACPI: Using IOAPIC for interrupt routing
[ 0.316000] Error attaching device data
[ 0.316000] Error attaching device data
[ 0.324000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.324000] PCI: Probing PCI hardware (bus 00)
[ 0.324000] 0000:00:14.1: trying to change BAR0 from 0000 to 01F0
[ 0.324000] 0000:00:14.1: trying to change BAR1 from 0000 to 03F4
[ 0.324000] 0000:00:14.1: trying to change BAR2 from 0000 to 0170
[ 0.324000] 0000:00:14.1: trying to change BAR3 from 0000 to 0374
[ 0.324000] Boot video device is 0000:01:00.0
[ 0.324000] PCI: Transparent bridge - 0000:00:14.4
[ 0.324000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.324000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[ 0.324000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
[ 0.340000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.340000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.340000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.340000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.340000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.340000] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[ 0.344000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.344000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.344000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.344000] pnp: PnP ACPI init
[ 0.348000] pnp: PnP ACPI: found 17 devices
[ 0.348000] PnPBIOS: Disabled by ACPI PNP
[ 0.348000] SCSI subsystem initialized
[ 0.348000] libata version 2.20 loaded.
[ 0.348000] PCI: Using ACPI for IRQ routing
[ 0.348000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.356000] NET: Registered protocol family 8
[ 0.356000] NET: Registered protocol family 20
[ 0.356000] pnp: 00:01: iomem range 0x0-0x0 could not be reserved
[ 0.356000] pnp: 00:09: iomem range 0xffb80000-0xffbfffff could not be reserved
[ 0.356000] pnp: 00:09: iomem range 0xfed00000-0xfed003ff could not be reserved
[ 0.356000] pnp: 00:09: iomem range 0xff6ff000-0xff6ff7ff has been reserved
[ 0.356000] pnp: 00:09: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.356000] pnp: 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.356000] pnp: 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.356000] pnp: 00:0e: ioport range 0xa00-0xa0f has been reserved
[ 0.356000] pnp: 00:0e: ioport range 0x600-0x60f has been reserved
[ 0.356000] pnp: 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.356000] pnp: 00:10: iomem range 0x0-0x9ffff could not be reserved
[ 0.356000] pnp: 00:10: iomem range 0xc0000-0xcffff could not be reserved
[ 0.356000] pnp: 00:10: iomem range 0xe0000-0xfffff could not be reserved
[ 0.356000] pnp: 00:10: iomem range 0x100000-0x3fffffff could not be reserved
[ 0.360000] Time: hpet clocksource has been installed.
[ 0.388000] PCI: Bridge: 0000:00:02.0
[ 0.388000] IO window: disabled.
[ 0.388000] MEM window: fa900000-fe9fffff
[ 0.388000] PREFETCH window: bff00000-dfefffff
[ 0.388000] PCI: Bridge: 0000:00:14.4
[ 0.388000] IO window: b000-bfff
[ 0.388000] MEM window: fea00000-feafffff
[ 0.388000] PREFETCH window: 50000000-500fffff
[ 0.388000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.388000] NET: Registered protocol family 2
[ 0.428000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.428000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.428000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.428000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.432000] TCP reno registered
[ 0.444000] checking if image is initramfs... it is
[ 0.852000] Freeing initrd memory: 5020k freed
[ 0.852000] audit: initializing netlink socket (disabled)
[ 0.852000] audit(1174956492.848:1): initialized
[ 0.852000] highmem bounce pool size: 64 pages
[ 0.852000] VFS: Disk quotas dquot_6.5.1
[ 0.852000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.856000] io scheduler noop registered
[ 0.856000] io scheduler anticipatory registered
[ 0.856000] io scheduler deadline registered
[ 0.856000] io scheduler cfq registered (default)
[ 0.956000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.956000] assign_interrupt_mode Found MSI capability
[ 0.956000] Allocate Port Service[0000:00:02.0:pcie00]
[ 0.956000] isapnp: Scanning for PnP cards...
[ 1.308000] isapnp: No Plug & Play device found
[ 1.336000] Real Time Clock Driver v1.12ac
[ 1.336000] hpet_resources: 0xfed00000 is busy
[ 1.336000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.336000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.336000] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.336000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.336000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1.336000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1.340000] ahci 0000:00:12.0: version 2.1
[ 1.340000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 16
[ 2.344000] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 2.344000] ahci 0000:00:12.0: flags: 64bit ncq ilck pm led clo pmp pio slum part
[ 2.344000] ata1: SATA max UDMA/133 cmd 0xf8824d00 ctl 0x00000000 bmdma 0x00000000 irq 222
[ 2.344000] ata2: SATA max UDMA/133 cmd 0xf8824d80 ctl 0x00000000 bmdma 0x00000000 irq 222
[ 2.344000] ata3: SATA max UDMA/133 cmd 0xf8824e00 ctl 0x00000000 bmdma 0x00000000 irq 222
[ 2.344000] ata4: SATA max UDMA/133 cmd 0xf8824e80 ctl 0x00000000 bmdma 0x00000000 irq 222
[ 2.344000] scsi0 : ahci
[ 2.656000] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.656000] scsi1 : ahci
[ 3.140000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 33.140000] ata2.00: qc timeout (cmd 0xec)
[ 33.140000] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 34.120000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 64.120000] ata2.00: qc timeout (cmd 0xec)
[ 64.120000] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 64.120000] ata2.00: limiting speed to UDMA7:PIO5
[ 65.100000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 95.100000] ata2.00: qc timeout (cmd 0xec)
[ 95.100000] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 96.080000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 96.080000] scsi2 : ahci
[ 96.392000] ata3: SATA link down (SStatus 0 SControl 300)
[ 96.392000] scsi3 : ahci
[ 96.704000] ata4: SATA link down (SStatus 0 SControl 300)
[ 96.704000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 96.704000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 96.704000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 96.704000] mice: PS/2 mouse device common for all mice
[ 96.704000] EISA: Probing bus 0 at eisa.0
[ 96.704000] EISA: Detected 0 cards.
[ 96.704000] TCP cubic registered
[ 96.704000] NET: Registered protocol family 1
[ 96.704000] Starting balanced_irq
[ 96.704000] Using IPI No-Shortcut mode
[ 96.708000] Freeing unused kernel memory: 332k freed
[ 96.724000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 96.780000] ACPI: duty_cycle spans bit 4
[ 97.236000] SB600_PATA: IDE controller at PCI slot 0000:00:14.1
[ 97.240000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
[ 97.240000] SB600_PATA: chipset revision 0
[ 97.240000] SB600_PATA: not 100% native mode: will probe irqs later
[ 97.240000] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[ 97.240000] Probing IDE interface ide0...
[ 97.528000] hda: HDS728080PLAT20, ATA DISK drive
[ 97.976000] hdb: ASUS DRW-1608P3S, ATAPI CD/DVD-ROM drive
[ 98.032000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 98.052000] hda: max request size: 512KiB
[ 98.056000] hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(100)
[ 98.056000] hda: cache flushes supported
[ 98.056000] hda: hda1 hda2 < hda5 hda6 >
[ 98.108000] hdb: ATAPI 63X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache, UDMA(66)
[ 98.108000] Uniform CD-ROM driver Revision: 3.20
[ 98.356000] Probing IDE interface ide1...
[ 98.368000] usbcore: registered new interface driver usbfs
[ 98.368000] usbcore: registered new interface driver hub
[ 98.368000] usbcore: registered new device driver usb
[ 98.368000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 98.368000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 98.372000] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 98.372000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 98.372000] ohci_hcd 0000:00:13.0: irq 17, io mem 0xfebfe000
[ 98.432000] usb usb1: configuration #1 chosen from 1 choice
[ 98.432000] hub 1-0:1.0: USB hub found
[ 98.432000] hub 1-0:1.0: 2 ports detected
[ 98.536000] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 18
[ 98.536000] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 98.536000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 98.536000] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfebfd000
[ 98.596000] usb usb2: configuration #1 chosen from 1 choice
[ 98.596000] hub 2-0:1.0: USB hub found
[ 98.596000] hub 2-0:1.0: 2 ports detected
[ 98.700000] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 19
[ 98.700000] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 98.700000] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 98.700000] ohci_hcd 0000:00:13.2: irq 19, io mem 0xfebfc000
[ 98.760000] usb usb3: configuration #1 chosen from 1 choice
[ 98.760000] hub 3-0:1.0: USB hub found
[ 98.760000] hub 3-0:1.0: 2 ports detected
[ 98.864000] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 18
[ 98.864000] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 98.864000] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
[ 98.864000] ohci_hcd 0000:00:13.3: irq 18, io mem 0xfebfb000
[ 98.924000] usb usb4: configuration #1 chosen from 1 choice
[ 98.924000] hub 4-0:1.0: USB hub found
[ 98.924000] hub 4-0:1.0: 2 ports detected
[ 99.028000] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 19
[ 99.028000] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 99.028000] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
[ 99.028000] ohci_hcd 0000:00:13.4: irq 19, io mem 0xfebfa000
[ 99.088000] usb usb5: configuration #1 chosen from 1 choice
[ 99.088000] hub 5-0:1.0: USB hub found
[ 99.088000] hub 5-0:1.0: 2 ports detected
[ 99.192000] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 20
[ 99.192000] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 99.192000] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
[ 99.192000] ehci_hcd 0000:00:13.5: debug port 1
[ 99.192000] ehci_hcd 0000:00:13.5: irq 20, io mem 0xfebff800
[ 99.192000] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 99.192000] usb usb6: configuration #1 chosen from 1 choice
[ 99.192000] hub 6-0:1.0: USB hub found
[ 99.192000] hub 6-0:1.0: 10 ports detected
[ 99.328000] Attempting manual resume
[ 99.368000] kjournald starting. Commit interval 5 seconds
[ 99.368000] EXT3-fs: mounted filesystem with ordered data mode.
[ 107.608000] input: PC Speaker as /class/input/input1
[ 107.716000] Floppy drive(s): fd0 is 1.44M
[ 107.772000] FDC 0 is a post-1991 82077
[ 107.776000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 107.796000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 107.856000] Linux agpgart interface v0.102 (c) Dave Jones
[ 107.940000] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 108.180000] parport: PnPBIOS parport detected.
[ 108.180000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 108.272000] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 108.272000] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 108.272000] eth0: RTL8169sc/8110sc at 0xf891e800, 00:16:17:c3:b8:f9, IRQ 21
[ 108.344000] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
[ 108.404000] r8169: eth0: link down
[ 108.544000] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 108.828000] lp0: using parport0 (interrupt-driven).
[ 108.888000] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[ 108.960000] w83627ehf: unsupported chip ID: 0xffff
[ 109.020000] Adding 1052216k swap on /dev/disk/by-uuid/ba363ce4-0f51-4ff4-abdb-c02e7467cc43. Priority:-1 extents:1 across:1052216k
[ 109.108000] EXT3 FS on hda5, internal journal
[ 109.428000] NTFS driver 2.1.28 [Flags: R/O MODULE].
[ 109.492000] NTFS volume version 3.1.
[ 109.532000] NET: Registered protocol family 17
[ 109.840000] r8169: eth0: link up
[ 111.800000] input: Power Button (FF) as /class/input/input3
[ 111.800000] ACPI: Power Button (FF) [PWRF]
[ 111.800000] input: Power Button (CM) as /class/input/input4
[ 111.800000] ACPI: Power Button (CM) [PWRB]
[ 111.864000] No dock devices found.
[ 111.892000] ibm_acpi: ec object not found
[ 111.948000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 112.192000] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ processors (version 2.00.00)
[ 112.192000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0xe
[ 112.192000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x10
[ 112.192000] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
[ 113.036000] NET: Registered protocol family 10
[ 113.036000] lo: Disabled Privacy Extensions
[ 114.868000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 114.868000] apm: disabled - APM is not SMP safe.
[ 116.824000] tsdev (compaq touchscreen emulation) is scheduled for removal.
[ 116.824000] See Documentation/feature-removal-schedule.txt for details.
[ 117.616000] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 120.228000] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 120.344000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 120.344000] NFSD: starting 90-second grace period
[ 123.444000] eth0: no IPv6 routers present
[ 124.000000] Clocksource tsc unstable (delta = -249947179 ns)
[ 134.036000] ISO 9660 Extensions: RRIP_1991A
matias
description: Desktop Computer
product: MS-7242
vendor: MSI
version: 0A
serial: To Be Filled By O.E.M.
width: 32 bits
capabilities: smbios-2.4 dmi-2.4
configuration: chassis=desktop uuid=00020003-0004-0005-0006-000700080009
*-core
description: Motherboard
product: MS-7242
vendor: MSI
physical id: 0
version: 0A
serial: To be filled by O.E.M.
slot: To Be Filled By O.E.M.
*-firmware
description: BIOS
vendor: American Megatrends Inc.
physical id: 0
version: 080013 (07/04/2006)
size: 64KB
capacity: 448KB
capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification
*-cpu
description: CPU
product: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+
vendor: Advanced Micro Devices [AMD]
physical id: 4
bus info: cpu@0
version: 15.11.2
serial: To Be Filled By O.E.M.
slot: CPU 1
size: 1GHz
capacity: 2GHz
width: 64 bits
clock: 200MHz
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt x86-64 3dnowext 3dnow pni cx16 lahf_lm cmp_legacy svm cr8legacy ts fid vid ttp tm stc cpufreq
*-cache:0
description: L1 cache
physical id: 5
slot: L1-Cache
size: 128KB
capacity: 128KB
capabilities: pipeline-burst internal varies data
*-cache:1
description: L2 cache
physical id: 6
slot: L2-Cache
size: 256KB
capacity: 512KB
capabilities: pipeline-burst internal varies unified
*-cache:2 DISABLED
description: L3 cache
physical id: 7
slot: L3-Cache
capabilities: internal
*-memory
description: System Memory
physical id: 28
slot: System board or motherboard
size: 1GB
*-bank:0
description: DIMM Synchronous 266 MHz (3.8 ns)
product: PartNum0
vendor: Manufacturer0
physical id: 0
serial: SerNum0
slot: DIMM0
size: 512MB
width: 64 bits
clock: 266MHz (3.7594ns)
*-bank:1
description: DIMM SDRAM [empty]
product: PartNum1
vendor: Manufacturer1
physical id: 1
serial: SerNum1
slot: DIMM1
*-bank:2
description: DIMM Synchronous 266 MHz (3.8 ns)
product: PartNum2
vendor: Manufacturer2
physical id: 2
serial: SerNum2
slot: DIMM2
size: 512MB
width: 64 bits
clock: 266MHz (3.7594ns)
*-bank:3
description: DIMM SDRAM [empty]
product: PartNum3
vendor: Manufacturer3
physical id: 3
serial: SerNum3
slot: DIMM3
*-pci:0
description: Host bridge
product: RS480 Host Bridge
vendor: ATI Technologies Inc
physical id: 100
bus info: pci@00:00.0
version: 10
width: 32 bits
clock: 66MHz
*-pci:0
description: PCI bridge
product: RS480 PCI-X Root Port
vendor: ATI Technologies Inc
physical id: 2
bus info: pci@00:02.0
version: 00
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master cap_list
configuration: driver=pcieport-driver
*-display
description: VGA compatible controller
product: G71 [GeForce 7300 GS]
vendor: nVidia Corporation
physical id: 0
bus info: pci@01:00.0
version: a1
size: 256MB
width: 64 bits
clock: 33MHz
capabilities: vga bus_master cap_list
resources: iomemory:fd000000-fdffffff iomemory:c0000000-cfffffff iomemory:fc000000-fcffffff irq:10
*-storage
description: SATA controller
product: SB600 Non-Raid-5 SATA
vendor: ATI Technologies Inc
physical id: 12
bus info: pci@00:12.0
logical name: scsi1
version: 00
width: 32 bits
clock: 66MHz
capabilities: storage ahci_1.0 bus_master cap_list emulated
configuration: driver=ahci
resources: ioport:e800-e807 ioport:e400-e403 ioport:e000-e007 ioport:dc00-dc03 ioport:d800-d80f iomemory:febffc00-febfffff irq:222
*-disk
description: SCSI Disk
product: HDS728080PLA380
vendor: ATA
physical id: 0.0.0
bus info: scsi@1:0.0.0
logical name: /dev/sda
version: PF2O
serial: PFDH37SYTWKR9E
size: 76GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume
description: HPFS/NTFS partition
physical id: 1
bus info: scsi@1:0.0.0,1
logical name: /dev/sda1
capacity: 19GB
capabilities: primary bootable
*-usb:0
description: USB Controller
product: SB600 USB (OHCI0)
vendor: ATI Technologies Inc
physical id: 13
bus info: pci@00:13.0
version: 00
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd
resources: iomemory:febfe000-febfefff irq:17
*-usbhost
product: OHCI Host Controller
vendor: Linux 2.6.20.4 ohci_hcd
physical id: 1
bus info: usb@1
logical name: usb1
version: 2.06
capabilities: usb-1.10
configuration: driver=hub maxpower=0mA slots=2 speed=12.0MB/s
*-usb:1
description: USB Controller
product: SB600 USB (OHCI1)
vendor: ATI Technologies Inc
physical id: 13.1
bus info: pci@00:13.1
version: 00
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd
resources: iomemory:febfd000-febfdfff irq:19
*-usbhost
product: OHCI Host Controller
vendor: Linux 2.6.20.4 ohci_hcd
physical id: 1
bus info: usb@3
logical name: usb3
version: 2.06
capabilities: usb-1.10
configuration: driver=hub maxpower=0mA slots=2 speed=12.0MB/s
*-usb:2
description: USB Controller
product: SB600 USB (OHCI2)
vendor: ATI Technologies Inc
physical id: 13.2
bus info: pci@00:13.2
version: 00
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd
resources: iomemory:febfc000-febfcfff irq:20
*-usbhost
product: OHCI Host Controller
vendor: Linux 2.6.20.4 ohci_hcd
physical id: 1
bus info: usb@4
logical name: usb4
version: 2.06
capabilities: usb-1.10
configuration: driver=hub maxpower=0mA slots=2 speed=12.0MB/s
*-usb:3
description: USB Controller
product: SB600 USB (OHCI3)
vendor: ATI Technologies Inc
physical id: 13.3
bus info: pci@00:13.3
version: 00
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd
resources: iomemory:febfb000-febfbfff irq:19
*-usbhost
product: OHCI Host Controller
vendor: Linux 2.6.20.4 ohci_hcd
physical id: 1
bus info: usb@5
logical name: usb5
version: 2.06
capabilities: usb-1.10
configuration: driver=hub maxpower=0mA slots=2 speed=12.0MB/s
*-usb:4
description: USB Controller
product: SB600 USB (OHCI4)
vendor: ATI Technologies Inc
physical id: 13.4
bus info: pci@00:13.4
version: 00
width: 32 bits
clock: 66MHz
capabilities: ohci bus_master cap_list
configuration: driver=ohci_hcd
resources: iomemory:febfa000-febfafff irq:20
*-usbhost
product: OHCI Host Controller
vendor: Linux 2.6.20.4 ohci_hcd
physical id: 1
bus info: usb@6
logical name: usb6
version: 2.06
capabilities: usb-1.10
configuration: driver=hub maxpower=0mA slots=2 speed=12.0MB/s
*-usb:5
description: USB Controller
product: SB600 USB Controller (EHCI)
vendor: ATI Technologies Inc
physical id: 13.5
bus info: pci@00:13.5
version: 00
width: 32 bits
clock: 66MHz
capabilities: ehci bus_master cap_list
configuration: driver=ehci_hcd
resources: iomemory:febff800-febff8ff irq:18
*-usbhost
product: EHCI Host Controller
vendor: Linux 2.6.20.4 ehci_hcd
physical id: 1
bus info: usb@2
logical name: usb2
version: 2.06
capabilities: usb-2.00
configuration: driver=hub maxpower=0mA slots=10 speed=480.0MB/s
*-serial UNCLAIMED
description: SMBus
product: SB600 SMBus
vendor: ATI Technologies Inc
physical id: 14
bus info: pci@00:14.0
version: 13
width: 32 bits
clock: 66MHz
capabilities: cap_list
resources: ioport:b00-b0f
*-ide
description: IDE interface
product: SB600 IDE
vendor: ATI Technologies Inc
physical id: 14.1
bus info: pci@00:14.1
version: 00
width: 32 bits
clock: 66MHz
capabilities: ide bus_master cap_list
configuration: driver=ATIIXP_IDE
resources: ioport:1f0-1f7 ioport:3f4-3f3 ioport:170-177 ioport:374-373 ioport:ff00-ff0f irq:17
*-ide
description: IDE Channel 0
physical id: 0
bus info: ide@0
logical name: ide0
clock: 66MHz
*-disk
description: ATA Disk
product: HDS728080PLAT20
physical id: 0
bus info: ide@xxx
logical name: /dev/hda
version: PF2OA21B
serial: PFD200E1DN2E7B
size: 76GB
capacity: 76GB
capabilities: ata dma lba iordy smart security pm apm partitioned partitioned:dos
configuration: apm=off mode=udma2 smart=on
*-volume:0
description: HPFS/NTFS partition
physical id: 1
bus info: ide@xxx,1
logical name: /dev/hda1
capacity: 18GB
capabilities: primary bootable
*-volume:1
description: W95 Ext'd (LBA) partition
physical id: 2
bus info: ide@xxx,2
logical name: /dev/hda2
capacity: 58GB
capabilities: primary
*-cdrom
description: DVD-RAM writer
product: ASUS DRW-1608P3S
physical id: 1
bus info: ide@xxx
logical name: /dev/hdb
version: 1.24
capabilities: packet atapi cdrom removable nonmagnetic dma lba iordy pm audio cd-r cd-rw dvd dvd-r dvd-ram
configuration: mode=udma4
*-disc
physical id: 0
logical name: /dev/hdb
*-multimedia
description: Audio device
product: SB600 Azalia
vendor: ATI Technologies Inc
physical id: 14.2
bus info: pci@00:14.2
version: 00
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list
configuration: driver=HDA Intel
resources: iomemory:febf4000-febf7fff irq:17
*-isa UNCLAIMED
description: ISA bridge
product: SB600 PCI to LPC Bridge
vendor: ATI Technologies Inc
physical id: 14.3
bus info: pci@00:14.3
version: 00
width: 32 bits
clock: 66MHz
capabilities: isa bus_master
*-pci:1
description: PCI bridge
product: SB600 PCI to PCI Bridge
vendor: ATI Technologies Inc
physical id: 14.4
bus info: pci@00:14.4
version: 00
width: 32 bits
clock: 66MHz
capabilities: pci subtractive_decode bus_master
*-network
description: Ethernet interface
product: RTL-8110SC/8169SC Gigabit Ethernet
vendor: Realtek Semiconductor Co., Ltd.
physical id: 6
bus info: pci@02:06.0
logical name: eth0
version: 10
serial: 00:16:17:c3:b8:f9
size: 100MB/s
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegociation
configuration: autonegociation=on broadcast=yes driver=r8169 driverversion=2.2LK duplex=full ip=192.168.0.2 link=yes multicast=yes port=twisted pair speed=100MB/s
resources: ioport:b800-b8ff iomemory:feaff800-feaff8ff irq:21
*-pci:1
description: Host bridge
product: K8 [Athlon64/Opteron] HyperTransport Technology Configuration
vendor: Advanced Micro Devices [AMD]
physical id: 101
bus info: pci@00:18.0
version: 00
width: 32 bits
clock: 33MHz
*-pci:2
description: Host bridge
product: K8 [Athlon64/Opteron] Address Map
vendor: Advanced Micro Devices [AMD]
physical id: 102
bus info: pci@00:18.1
version: 00
width: 32 bits
clock: 33MHz
*-pci:3
description: Host bridge
product: K8 [Athlon64/Opteron] DRAM Controller
vendor: Advanced Micro Devices [AMD]
physical id: 103
bus info: pci@00:18.2
version: 00
width: 32 bits
clock: 33MHz
*-pci:4
description: Host bridge
product: K8 [Athlon64/Opteron] Miscellaneous Control
vendor: Advanced Micro Devices [AMD]
physical id: 104
bus info: pci@00:18.3
version: 00
width: 32 bits
clock: 33MHz
