Lukas Hejtmanek wrote:
>> Subject : ata_piix: PATA UDMA/100 configured as UDMA/33
>> References : http://lkml.org/lkml/2007/2/20/294
>> Submitter : Fabio Comolli <fabio.comolli@xxxxxxxxx>
>> Status : unknown
>
> ata_piix 0000:00:1f.1: version 2.10ac1
> ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1f.1 to 64
> ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
> ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
> scsi0 : ata_piix
> Time: acpi_pm clocksource has been installed.
> Switched to high resolution mode on CPU 0
> ata1.00: ATA-6: ST9100824A, 3.04, max UDMA/100
> ata1.00: 195371568 sectors, multi 16: LBA48
> ata1.01: ATAPI, max UDMA/33
> ata1.00: configured for UDMA/33
> ata1.01: configured for UDMA/33
> scsi1 : ata_piix
> ATA: abnormal status 0x7F on port 0x00010177
> scsi 0:0:0:0: Direct-Access ATA ST9100824A 3.04 PQ: 0 ANSI: 5
> SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
Does this fix your problem?
--
tejun
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 361953a..c89664a 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1743,12 +1743,17 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
{
struct ata_eh_context *ehc = &ap->eh_context;
struct ata_device *dev;
+ unsigned int new_mask = 0;
unsigned long flags;
int i, rc = 0;
DPRINTK("ENTER\n");
- for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ /* For PATA drive side cable detection to work, IDENTIFY must
+ * be done backwards such that PDIAG- is released by the slave
+ * device before the master device is identified.
+ */
+ for (i = ATA_MAX_DEVICES - 1; i >= 0; i--) {
unsigned int action, readid_flags = 0;
dev = &ap->device[i];
@@ -1760,13 +1765,13 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
if (action & ATA_EH_REVALIDATE && ata_dev_ready(dev)) {
if (ata_port_offline(ap)) {
rc = -EIO;
- break;
+ goto err;
}
ata_eh_about_to_do(ap, dev, ATA_EH_REVALIDATE);
rc = ata_dev_revalidate(dev, readid_flags);
if (rc)
- break;
+ goto err;
ata_eh_done(ap, dev, ATA_EH_REVALIDATE);
@@ -1784,40 +1789,53 @@ static int ata_eh_revalidate_and_attach(struct ata_port *ap,
rc = ata_dev_read_id(dev, &dev->class, readid_flags,
dev->id);
- if (rc == 0) {
- ehc->i.flags |= ATA_EHI_PRINTINFO;
- rc = ata_dev_configure(dev);
- ehc->i.flags &= ~ATA_EHI_PRINTINFO;
- } else if (rc == -ENOENT) {
+ switch (rc) {
+ case 0:
+ new_mask |= 1 << i;
+ break;
+ case -ENOENT:
/* IDENTIFY was issued to non-existent
* device. No need to reset. Just
* thaw and kill the device.
*/
ata_eh_thaw_port(ap);
dev->class = ATA_DEV_UNKNOWN;
- rc = 0;
- }
-
- if (rc) {
- dev->class = ATA_DEV_UNKNOWN;
break;
+ default:
+ dev->class = ATA_DEV_UNKNOWN;
+ goto err;
}
+ }
+ }
- if (ata_dev_enabled(dev)) {
- spin_lock_irqsave(ap->lock, flags);
- ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
- spin_unlock_irqrestore(ap->lock, flags);
+ /* Configure new devices forward such that user doesn't see
+ * device detection messages backwards.
+ */
+ for (i = 0; i < ATA_MAX_DEVICES; i++) {
+ dev = &ap->device[i];
- /* new device discovered, configure xfermode */
- ehc->i.flags |= ATA_EHI_SETMODE;
- }
- }
+ if (!(new_mask & (1 << i)))
+ continue;
+
+ ehc->i.flags |= ATA_EHI_PRINTINFO;
+ rc = ata_dev_configure(dev);
+ ehc->i.flags &= ~ATA_EHI_PRINTINFO;
+ if (rc)
+ goto err;
+
+ spin_lock_irqsave(ap->lock, flags);
+ ap->pflags |= ATA_PFLAG_SCSI_HOTPLUG;
+ spin_unlock_irqrestore(ap->lock, flags);
+
+ /* new device discovered, configure xfermode */
+ ehc->i.flags |= ATA_EHI_SETMODE;
}
- if (rc)
- *r_failed_dev = dev;
+ return 0;
- DPRINTK("EXIT\n");
+ err:
+ *r_failed_dev = dev;
+ DPRINTK("EXIT rc=%d\n", rc);
return rc;
}
