A lot of noise because I had to rename the optidma_set_mode() method to
avoid confusion with the new ->set_mode() method that was added. Cable
detect side is pretty trivial.
Signed-off-by: Alan Cox <alan@xxxxxxxxxx>
diff -u --new-file --recursive --exclude-from /usr/src/exclude linux.vanilla-2.6.21-rc3-mm2/drivers/ata/pata_optidma.c linux-2.6.21-rc3-mm2/drivers/ata/pata_optidma.c
--- linux.vanilla-2.6.21-rc3-mm2/drivers/ata/pata_optidma.c 2007-03-08 16:01:10.000000000 +0000
+++ linux-2.6.21-rc3-mm2/drivers/ata/pata_optidma.c 2007-03-08 16:34:00.000000000 +0000
@@ -33,7 +33,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_optidma"
-#define DRV_VERSION "0.2.4"
+#define DRV_VERSION "0.3.2"
enum {
READ_REG = 0, /* index of Read cycle timing register */
@@ -62,8 +62,6 @@
if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits))
return -ENOENT;
-
- ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap, deadline);
}
@@ -116,7 +114,7 @@
}
/**
- * optidma_set_mode - set mode data
+ * optidma_mode_setup - set mode data
* @ap: ATA interface
* @adev: ATA device
* @mode: Mode to set
@@ -129,7 +127,7 @@
* IRQ here we depend on the host set locking to avoid catastrophe.
*/
-static void optidma_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode)
+static void optidma_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode)
{
struct ata_device *pair = ata_dev_pair(adev);
int pio = adev->pio_mode - XFER_PIO_0;
@@ -203,7 +201,7 @@
}
/**
- * optiplus_set_mode - DMA setup for Firestar Plus
+ * optiplus_mode_setup - DMA setup for Firestar Plus
* @ap: ATA port
* @adev: device
* @mode: desired mode
@@ -214,7 +212,7 @@
* one
*/
-static void optiplus_set_mode(struct ata_port *ap, struct ata_device *adev, u8 mode)
+static void optiplus_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 udcfg;
@@ -226,7 +224,7 @@
pci_read_config_byte(pdev, 0x44, &udcfg);
if (mode <= XFER_UDMA_0) {
udcfg &= ~(1 << unit);
- optidma_set_mode(ap, adev, adev->dma_mode);
+ optidma_mode_setup(ap, adev, adev->dma_mode);
} else {
udcfg |= (1 << unit);
if (ap->port_no) {
@@ -254,7 +252,7 @@
static void optidma_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
{
- optidma_set_mode(ap, adev, adev->pio_mode);
+ optidma_mode_setup(ap, adev, adev->pio_mode);
}
/**
@@ -269,7 +267,7 @@
static void optidma_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
{
- optidma_set_mode(ap, adev, adev->dma_mode);
+ optidma_mode_setup(ap, adev, adev->dma_mode);
}
/**
@@ -284,7 +282,7 @@
static void optiplus_set_pio_mode(struct ata_port *ap, struct ata_device *adev)
{
- optiplus_set_mode(ap, adev, adev->pio_mode);
+ optiplus_mode_setup(ap, adev, adev->pio_mode);
}
/**
@@ -299,7 +297,7 @@
static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev)
{
- optiplus_set_mode(ap, adev, adev->dma_mode);
+ optiplus_mode_setup(ap, adev, adev->dma_mode);
}
/**
@@ -323,26 +321,29 @@
}
/**
- * optidma_post_set_mode - finalize PCI setup
+ * optidma_set_mode - mode setup
* @ap: port to set up
*
- * Finalise the configuration by writing the nibble of extra bits
- * of data into the chip.
+ * Use the standard setup to tune the chipset and then finalise the
+ * configuration by writing the nibble of extra bits of data into
+ * the chip.
*/
-static void optidma_post_set_mode(struct ata_port *ap)
+static int optidma_set_mode(struct ata_port *ap, struct ata_device **r_failed)
{
u8 r;
int nybble = 4 * ap->port_no;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
- pci_read_config_byte(pdev, 0x43, &r);
-
- r &= (0x0F << nybble);
- r |= (optidma_make_bits43(&ap->device[0]) +
- (optidma_make_bits43(&ap->device[0]) << 2)) << nybble;
-
- pci_write_config_byte(pdev, 0x43, r);
+ int rc = ata_do_set_mode(ap, r_failed);
+ if (rc == 0) {
+ pci_read_config_byte(pdev, 0x43, &r);
+
+ r &= (0x0F << nybble);
+ r |= (optidma_make_bits43(&ap->device[0]) +
+ (optidma_make_bits43(&ap->device[0]) << 2)) << nybble;
+ pci_write_config_byte(pdev, 0x43, r);
+ }
+ return rc;
}
static struct scsi_host_template optidma_sht = {
@@ -382,7 +383,8 @@
.thaw = ata_bmdma_thaw,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.error_handler = optidma_error_handler,
- .post_set_mode = optidma_post_set_mode,
+ .set_mode = optidma_set_mode,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
@@ -417,7 +419,8 @@
.thaw = ata_bmdma_thaw,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.error_handler = optidma_error_handler,
- .post_set_mode = optidma_post_set_mode,
+ .set_mode = optidma_set_mode,
+ .cable_detect = ata_cable_40wire,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
