Tejun Heo wrote: > Eyal Lebedinsky wrote: > >>It is in the original thread on linux-raid, but here it is for this list. >>This is the full dmesg. There were only MARKs in between. >> >>I run a raid 'check' every Friday (cron). The last one reported some parity errors. >> >>*** last week check start: >>[927080.617744] md: data-check of RAID array md0 >>[927080.630783] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. >>[927080.648734] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. >>[927080.678103] md: using 128k window, over a total of 312568576 blocks. >> *** last week error: >>[937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2 >>[937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in >>[937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error) > > > I need full kernel log including the boot messages so that I can tell > which controller/driver is involved here and also the result of 'hdparm > -I /dev/sdX' of your drives would be nice. > > BTW, this is SMART read log for page 09 which is SMART self-test log. > The device aborted it. Dunno who issued it or why it got aborted. As I > wrote in the previous mail, EH discovered that SError has accumulated > link level errors and thus treated it as ATA bus error. All > transmissions over SATA are checksummed and link errors supposedly don't > cause data corruption, so, in theory, the above error message should be > irrelevant to your problem. > > Ah.. please also post the result of 'smartctl -d ata -a /dev/sdX' for > your drives. That might reveal something. sd[ab] are on the motherboard, sd[cdef] are on a Promise SATA-II-150-TX4. In smartd.conf all the disks run a full selftest once a week which may have coincided with the time of the reported error. -- Eyal Lebedinsky (eyal@xxxxxxxxxxxxxx) <http://samba.org/eyal/> attach .zip as .dat
[ 0.000000] Linux version 2.6.20 (eyal@e7) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Mon Feb 5 22:08:32 EST 2007 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] sanitize start [ 0.000000] sanitize end [ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2 [ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2 [ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1 [ 0.000000] copy_e820_map() type is E820_RAM [ 0.000000] copy_e820_map() start: 000000003fff0000 size: 0000000000003000 end: 000000003fff3000 type: 4 [ 0.000000] copy_e820_map() start: 000000003fff3000 size: 000000000000d000 end: 0000000040000000 type: 3 [ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000001400000 end: 0000000100000000 type: 2 [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) [ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] 127MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f5200 [ 0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 262128 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 262128 [ 0.000000] On node 0 totalpages: 262128 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 255 pages used for memmap [ 0.000000] HighMem zone: 32497 pages, LIFO batch:7 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v000 GBT ) @ 0x000f6ca0 [ 0.000000] ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3000 [ 0.000000] ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3040 [ 0.000000] ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff7080 [ 0.000000] ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:2 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) [ 0.000000] Detected 3014.582 MHz processor. [ 34.023123] Built 1 zonelists. Total pages: 260081 [ 34.023125] Kernel command line: BOOT_IMAGE=2.6.20 ro root=303 console=ttyS0,38400 console=tty0 single [ 34.023286] mapped APIC to ffffd000 (fee00000) [ 34.023288] mapped IOAPIC to ffffc000 (fec00000) [ 34.023290] Enabling fast FPU save and restore... done. [ 34.023293] Enabling unmasked SIMD FPU exception support... done. [ 34.023300] Initializing CPU#0 [ 34.023354] CPU 0 irqstacks, hard=c03b9000 soft=c03b8000 [ 34.023356] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 34.025791] Console: colour VGA+ 80x50 [ 34.937135] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 34.958712] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 34.996037] Memory: 1035532k/1048512k available (1609k kernel code, 12344k reserved, 879k data, 268k init, 131008k highmem) [ 35.029409] virtual kernel memory layout: [ 35.029410] fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB) [ 35.029411] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 35.029412] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 35.029413] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 35.029414] .init : 0xc0370000 - 0xc03b3000 ( 268 kB) [ 35.029415] .data : 0xc0292708 - 0xc036e490 ( 879 kB) [ 35.029416] .text : 0xc0100000 - 0xc0292708 (1609 kB) [ 35.162043] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 35.245674] Calibrating delay using timer specific routine.. 6030.90 BogoMIPS (lpj=3015453) [ 35.270840] Security Framework v1.0.0 initialized [ 35.284972] Mount-cache hash table entries: 512 [ 35.298669] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 35.298678] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 35.314171] CPU: L2 cache: 512K [ 35.323615] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 00000000 00000000 [ 35.323620] Intel machine check architecture supported. [ 35.339314] Intel machine check reporting enabled on CPU#0. [ 35.356045] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available [ 35.374076] CPU0: Thermal monitoring enabled [ 35.386921] Compat vDSO mapped to ffffe000. [ 35.399506] CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 [ 35.417142] Checking 'hlt' instruction... OK. [ 35.433730] ACPI: Core revision 20060707 [ 35.678402] ENABLING IO-APIC IRQs [ 35.688536] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 35.817614] NET: Registered protocol family 16 [ 35.831038] EISA bus registered [ 35.840499] ACPI: bus type pci registered [ 35.876470] PCI: PCI BIOS revision 2.10 entry at 0xfb500, last bus=3 [ 35.895519] PCI: Using configuration type 1 [ 35.908102] Setting up standard PCI resources [ 35.937233] ACPI: Interpreter enabled [ 35.948261] ACPI: Using IOAPIC for interrupt routing [ 35.963695] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 35.978100] PCI: Probing PCI hardware (bus 00) [ 35.978624] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO [ 35.997958] PCI quirk: region 1080-10bf claimed by ICH4 GPIO [ 36.015143] Boot video device is 0000:01:00.0 [ 36.015722] PCI: Transparent bridge - 0000:00:1e.0 [ 36.030134] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 36.037010] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 36.040728] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) [ 36.063634] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 36.086517] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 36.109389] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 36.132268] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. [ 36.158679] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 36.181556] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 36.204439] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) [ 36.228698] Linux Plug and Play Support v0.97 (c) Adam Belay [ 36.245676] pnp: PnP ACPI init [ 36.258805] pnp: PnP ACPI: found 16 devices [ 36.271380] PnPBIOS: Disabled by ACPI PNP [ 36.283478] PCI: Using ACPI for IRQ routing [ 36.296048] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 36.349537] PCI: Bridge: 0000:00:01.0 [ 36.360543] IO window: disabled. [ 36.370791] MEM window: d8000000-d9ffffff [ 36.383372] PREFETCH window: c0000000-cfffffff [ 36.397253] PCI: Bridge: 0000:00:03.0 [ 36.408276] IO window: a000-afff [ 36.418500] MEM window: da000000-dbffffff [ 36.431081] PREFETCH window: 50000000-500fffff [ 36.444962] PCI: Bridge: 0000:00:1e.0 [ 36.455986] IO window: 8000-9fff [ 36.466209] MEM window: dc000000-ddffffff [ 36.478791] PREFETCH window: de000000-de0fffff [ 36.492682] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 36.492703] NET: Registered protocol family 2 [ 36.514926] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 36.536458] TCP established hash table entries: 131072 (order: 7, 524288 bytes) [ 36.558646] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) [ 36.578662] TCP: Hash tables configured (established 131072 bind 65536) [ 36.598487] TCP reno registered [ 36.610925] Machine check exception polling timer started. [ 36.627525] highmem bounce pool size: 64 pages [ 36.640879] Total HugeTLB memory allocated, 0 [ 36.654019] VFS: Disk quotas dquot_6.5.1 [ 36.665826] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 36.685644] io scheduler noop registered [ 36.697510] io scheduler anticipatory registered (default) [ 36.714110] io scheduler deadline registered [ 36.727011] io scheduler cfq registered [ 36.738970] isapnp: Scanning for PnP cards... [ 37.107853] isapnp: No Plug & Play device found [ 37.139266] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 37.162877] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 37.181059] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 37.199621] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 37.216568] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 37.233598] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 37.252667] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 37.276702] ICH5: IDE controller at PCI slot 0000:00:1f.1 [ 37.292904] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16 [ 37.315212] ICH5: chipset revision 2 [ 37.325971] ICH5: not 100% native mode: will probe irqs later [ 37.343230] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio [ 37.365071] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio [ 37.386911] Probing IDE interface ide0... [ 37.649527] hda: WDC WD2500JB-00REA0, ATA DISK drive [ 38.275129] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 38.288839] Probing IDE interface ide1... [ 38.958653] hdc: ATAPI DVD RW 8XMax, ATAPI CD/DVD-ROM drive [ 39.280987] ide1 at 0x170-0x177,0x376 on irq 15 [ 39.294770] hda: max request size: 512KiB [ 39.322149] hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100) [ 39.347572] hda: cache flushes supported [ 39.359377] hda: hda1 hda2 hda3 hda4 [ 39.389031] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 39.414497] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 39.429402] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 39.444658] mice: PS/2 mouse device common for all mice [ 39.460436] EISA: Probing bus 0 at eisa.0 [ 39.472500] Cannot allocate resource for EISA slot 1 [ 39.487433] Cannot allocate resource for EISA slot 8 [ 39.502354] EISA: Detected 0 cards. [ 39.542862] TCP cubic registered [ 39.552606] Using IPI Shortcut mode [ 39.563191] Time: tsc clocksource has been installed. [ 39.587707] input: AT Translated Set 2 keyboard as /class/input/input0 [ 39.711228] EXT2-fs warning (device hda3): ext2_fill_super: mounting ext3 filesystem as ext2 [ 39.736713] VFS: Mounted root (ext2 filesystem) readonly. [ 39.753089] Freeing unused kernel memory: 268k freed [ 40.329868] NET: Registered protocol family 1 [ 41.347430] Adding 2104504k swap on /dev/hda2. Priority:1 extents:1 across:2104504k [ 45.753592] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx [ 46.284862] kjournald starting. Commit interval 5 seconds [ 46.301511] EXT3 FS on hda4, internal journal [ 46.314655] EXT3-fs: mounted filesystem with ordered data mode. [ 47.530305] Linux agpgart interface v0.101 (c) Dave Jones [ 47.575186] agpgart: Detected an Intel 865 Chipset. [ 47.605367] agpgart: AGP aperture is 128M @ 0xd0000000 [ 48.224088] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 48.273692] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 49.434533] usbcore: registered new interface driver usbfs [ 49.459572] usbcore: registered new interface driver hub [ 49.484100] usbcore: registered new device driver usb [ 49.522676] USB Universal Host Controller Interface driver v3.0 [ 49.549120] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 49.571423] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 49.571427] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 49.596116] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 49.618354] uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000bc00 [ 49.642587] usb usb1: configuration #1 chosen from 1 choice [ 49.659859] hub 1-0:1.0: USB hub found [ 49.671154] hub 1-0:1.0: 2 ports detected [ 50.171917] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18 [ 50.194228] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 50.194231] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 50.212840] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 50.235081] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000b000 [ 50.254029] usb usb2: configuration #1 chosen from 1 choice [ 50.271128] hub 2-0:1.0: USB hub found [ 50.283895] hub 2-0:1.0: 2 ports detected [ 50.462323] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16 [ 50.484634] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 50.484637] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 50.534170] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 50.556413] uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000b400 [ 50.792160] usb usb3: configuration #1 chosen from 1 choice [ 50.809942] hub 3-0:1.0: USB hub found [ 50.821251] hub 3-0:1.0: 2 ports detected [ 51.735367] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 17 [ 51.757664] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 51.757668] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 51.781907] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 51.804145] uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000b800 [ 51.832859] usb usb4: configuration #1 chosen from 1 choice [ 51.850102] hub 4-0:1.0: USB hub found [ 51.861391] hub 4-0:1.0: 2 ports detected [ 52.886898] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 18 (level, low) -> IRQ 16 [ 52.909203] uhci_hcd 0000:03:04.0: UHCI Host Controller [ 52.933575] uhci_hcd 0000:03:04.0: new USB bus registered, assigned bus number 5 [ 52.955817] uhci_hcd 0000:03:04.0: irq 16, io base 0x00008c00 [ 52.984545] usb usb5: configuration #1 chosen from 1 choice [ 53.001788] hub 5-0:1.0: USB hub found [ 53.013090] hub 5-0:1.0: 2 ports detected [ 53.734460] ACPI: PCI Interrupt 0000:03:04.1[B] -> GSI 21 (level, low) -> IRQ 19 [ 53.756750] uhci_hcd 0000:03:04.1: UHCI Host Controller [ 53.776027] uhci_hcd 0000:03:04.1: new USB bus registered, assigned bus number 6 [ 53.798276] uhci_hcd 0000:03:04.1: irq 19, io base 0x00009000 [ 53.818005] usb usb6: configuration #1 chosen from 1 choice [ 53.835960] hub 6-0:1.0: USB hub found [ 53.847240] hub 6-0:1.0: 2 ports detected [ 54.050380] usb 5-1: new full speed USB device using uhci_hcd and address 2 [ 54.224345] usb 5-1: configuration #1 chosen from 1 choice [ 60.832283] dib0700: loaded with support for 2 different device-types [ 60.868572] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 60.954450] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw' [ 62.411983] dib0700: firmware started successfully. [ 62.664544] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20 [ 62.686862] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 62.686866] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 62.702928] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 [ 62.725171] PCI: cache line size of 128 is not supported by device 0000:00:1d.7 [ 62.725180] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xde100000 [ 62.746049] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 62.769313] usb usb7: configuration #1 chosen from 1 choice [ 62.786438] hub 7-0:1.0: USB hub found [ 62.797742] hub 7-0:1.0: 8 ports detected [ 62.910706] ACPI: PCI Interrupt 0000:03:04.2[C] -> GSI 22 (level, low) -> IRQ 21 [ 62.933002] ehci_hcd 0000:03:04.2: EHCI Host Controller [ 62.949106] ehci_hcd 0000:03:04.2: new USB bus registered, assigned bus number 8 [ 62.971350] ehci_hcd 0000:03:04.2: irq 21, io mem 0xdd025000 [ 62.988333] ehci_hcd 0000:03:04.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 63.011576] usb usb8: configuration #1 chosen from 1 choice [ 63.028690] hub 8-0:1.0: USB hub found [ 63.039988] hub 8-0:1.0: 4 ports detected [ 63.186321] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state. [ 63.207732] **WARNING** I2C adapter driver [Hauppauge Nova-T 500 Dual DVB-T] forgot to specify physical device; fix it! [ 63.240174] dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter) [ 63.269349] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T error while loading driver (-19) [ 63.458715] usb 8-1: new high speed USB device using ehci_hcd and address 2 [ 63.595168] usb 8-1: configuration #1 chosen from 1 choice [ 63.614016] usb 5-1: USB disconnect, address 2 [ 63.627508] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in warm state. [ 63.648918] **WARNING** I2C adapter driver [Hauppauge Nova-T 500 Dual DVB-T] forgot to specify physical device; fix it! [ 63.681950] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 63.707223] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T). [ 63.793318] **WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it! [ 63.824633] DVB: registering frontend 0 (DiBcom 3000MC/P)... [ 63.861561] MT2060: successfully identified (IF1 = 1220) [ 64.302857] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 64.328158] DVB: registering new adapter (Hauppauge Nova-T 500 Dual DVB-T). [ 64.351637] **WARNING** I2C adapter driver [DiBX000 tuner I2C bus] forgot to specify physical device; fix it! [ 64.382579] DVB: registering frontend 1 (DiBcom 3000MC/P)... [ 64.401666] MT2060: successfully identified (IF1 = 1220) [ 64.733196] intel_rng: FWH not detected [ 64.807042] iTCO_vendor_support: vendor-support=0 [ 64.824848] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006) [ 64.846039] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x1060) [ 64.869166] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1) [ 64.931292] dvb-usb: Hauppauge Nova-T 500 Dual DVB-T successfully initialized and connected. [ 64.956680] usbcore: registered new interface driver dvb_usb_dib0700 [ 65.668661] SCSI subsystem initialized [ 65.695351] libata version 2.00 loaded. [ 65.752396] ata_piix 0000:00:1f.2: version 2.00ac7 [ 65.752402] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] [ 65.768301] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16 [ 65.790610] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 65.790658] ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 16 [ 65.812095] ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xCC02 bmdma 0xD008 irq 16 [ 65.833522] scsi0 : ata_piix [ 65.996356] ata1.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48 [ 66.015162] ata1.00: ata1: dev 0 multi count 16 [ 66.031277] ata1.00: configured for UDMA/100 [ 66.044115] scsi1 : ata_piix [ 66.222858] ata2.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48 [ 66.241666] ata2.00: ata2: dev 0 multi count 16 [ 66.257780] ata2.00: configured for UDMA/100 [ 66.270694] scsi 0:0:0:0: Direct-Access ATA WDC WD3200SD-01K 08.0 PQ: 0 ANSI: 5 [ 66.295863] scsi 1:0:0:0: Direct-Access ATA WDC WD3200JD-00K 08.0 PQ: 0 ANSI: 5 [ 67.457380] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 22 [ 68.057582] Intel 810 + AC97 Audio, version 1.01, 23:31:07 Feb 5 2007 [ 68.077602] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22 [ 68.099940] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 68.099945] i810: Intel ICH5 found at IO 0xdc00 and 0xd800, MEM 0xde101000 and 0xde102000, IRQ 22 [ 68.126593] i810: Intel ICH5 mmio at 0xf89d2000 and 0xf89fe000 [ 68.642354] i810_audio: Primary codec has ID 2 [ 68.655743] i810_audio: Audio Controller supports 6 channels. [ 68.672984] i810_audio: Defaulting to base 2 channel mode. [ 68.689457] i810_audio: Resetting connection 0 [ 68.702854] i810_audio: Connection 0 with codec id 2 [ 68.718051] ac97_codec: AC97 Audio codec, id: ALG128 (Unknown) [ 68.736201] i810_audio: AC'97 codec 2 Unable to map surround DAC's (or DAC's not present), total channels = 2 [ 69.487042] Intel(R) PRO/1000 Network Driver - version 7.3.15-k2 [ 69.505098] Copyright (c) 1999-2006 Intel Corporation. [ 69.520930] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 16 [ 69.543269] PCI: Setting latency timer of device 0000:02:01.0 to 64 [ 69.874439] e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0d:61:69:86:83 [ 70.119427] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 70.705027] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 70.724017] 8139cp 0000:03:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip [ 70.749357] 8139cp 0000:03:00.0: Try the "8139too" driver instead. [ 70.812131] 8139too Fast Ethernet driver 0.9.28 [ 70.826204] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16 [ 70.849433] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16 [ 70.869032] eth1: Identified 8139 chip type 'RTL-8100B/8139D' [ 74.091716] sata_promise 0000:03:01.0: version 1.05 [ 74.091736] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 21 (level, low) -> IRQ 19 [ 74.114126] ata3: SATA max UDMA/133 cmd 0xF8CB2200 ctl 0xF8CB2238 bmdma 0x0 irq 19 [ 74.136918] ata4: SATA max UDMA/133 cmd 0xF8CB2280 ctl 0xF8CB22B8 bmdma 0x0 irq 19 [ 74.159695] ata5: SATA max UDMA/133 cmd 0xF8CB2300 ctl 0xF8CB2338 bmdma 0x0 irq 19 [ 74.182469] ata6: SATA max UDMA/133 cmd 0xF8CB2380 ctl 0xF8CB23B8 bmdma 0x0 irq 19 [ 74.205210] scsi2 : sata_promise [ 74.499107] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) [ 74.519243] sda: Write Protect is off [ 74.530264] sda: Mode Sense: 00 3a 00 00 [ 74.530309] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 74.557268] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB) [ 74.577380] sda: Write Protect is off [ 74.588400] sda: Mode Sense: 00 3a 00 00 [ 74.588425] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 74.615330] sda:<6>ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 74.801151] ata3.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48 [ 74.819964] ata3.00: ata3: dev 0 multi count 0 [ 74.836071] ata3.00: configured for UDMA/100 [ 74.848944] scsi3 : sata_promise [ 75.312714] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 75.333978] ata4.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48 [ 75.352800] ata4.00: ata4: dev 0 multi count 0 [ 75.368900] ata4.00: configured for UDMA/100 [ 75.381762] scsi4 : sata_promise [ 75.673652] sda1 [ 75.685917] sd 0:0:0:0: Attached scsi disk sda [ 75.700714] SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB) [ 75.720845] sdb: Write Protect is off [ 75.731873] sdb: Mode Sense: 00 3a 00 00 [ 75.731917] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 75.758853] SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB) [ 75.778963] sdb: Write Protect is off [ 75.789984] sdb: Mode Sense: 00 3a 00 00 [ 75.790009] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 75.816915] sdb:<6>ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 75.996538] ata5.00: ATA-6, max UDMA/100, 625142448 sectors: LBA48 [ 76.015350] ata5.00: ata5: dev 0 multi count 0 [ 76.031445] ata5.00: configured for UDMA/100 [ 76.044330] scsi5 : sata_promise [ 76.339534] sdb1 [ 76.348296] sd 1:0:0:0: Attached scsi disk sdb [ 76.525053] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 76.546319] ata6.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1) [ 76.569069] ata6.00: ata6: dev 0 multi count 0 [ 76.585229] ata6.00: configured for UDMA/133 [ 76.598869] scsi 2:0:0:0: Direct-Access ATA WDC WD3200JD-00K 08.0 PQ: 0 ANSI: 5 [ 76.624810] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB) [ 76.645279] sdc: Write Protect is off [ 76.656316] sdc: Mode Sense: 00 3a 00 00 [ 76.657249] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 76.685185] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB) [ 76.705621] sdc: Write Protect is off [ 76.716655] sdc: Mode Sense: 00 3a 00 00 [ 76.717594] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 76.744494] sdc: sdc1 [ 76.759221] sd 2:0:0:0: Attached scsi disk sdc [ 76.773499] scsi 3:0:0:0: Direct-Access ATA WDC WD3200JD-00K 08.0 PQ: 0 ANSI: 5 [ 76.799458] SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB) [ 76.819883] sdd: Write Protect is off [ 76.830916] sdd: Mode Sense: 00 3a 00 00 [ 76.831860] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 76.859802] SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB) [ 76.880239] sdd: Write Protect is off [ 76.891285] sdd: Mode Sense: 00 3a 00 00 [ 76.892211] SCSI device sdd: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 76.919120] sdd: sdd1 [ 76.930419] sd 3:0:0:0: Attached scsi disk sdd [ 76.945129] scsi 4:0:0:0: Direct-Access ATA WDC WD3200SD-01K 08.0 PQ: 0 ANSI: 5 [ 76.971059] SCSI device sde: 625142448 512-byte hdwr sectors (320073 MB) [ 76.991500] sde: Write Protect is off [ 77.002530] sde: Mode Sense: 00 3a 00 00 [ 77.003475] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 77.031417] SCSI device sde: 625142448 512-byte hdwr sectors (320073 MB) [ 77.051861] sde: Write Protect is off [ 77.062902] sde: Mode Sense: 00 3a 00 00 [ 77.063835] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 77.090723] sde: sde1 [ 77.107807] sd 4:0:0:0: Attached scsi disk sde [ 77.122727] scsi 5:0:0:0: Direct-Access ATA WDC WD3200YS-01P 21.0 PQ: 0 ANSI: 5 [ 77.149653] SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB) [ 77.170101] sdf: Write Protect is off [ 77.181135] sdf: Mode Sense: 00 3a 00 00 [ 77.182074] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 77.209514] SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB) [ 77.229966] sdf: Write Protect is off [ 77.240983] sdf: Mode Sense: 00 3a 00 00 [ 77.241939] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 77.268846] sdf: sdf1 [ 77.281040] sd 5:0:0:0: Attached scsi disk sdf [ 80.297720] Linux video capture interface: v2.00 [ 80.552483] bttv: driver version 0.9.16 loaded [ 80.565851] bttv: using 8 buffers with 2080k (520 pages) each for capture [ 80.594975] bttv: Bt8xx card found (0). [ 80.606548] ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 21 [ 80.628890] bttv0: Bt878 (rev 17) at 0000:03:02.0, irq: 21, latency: 32, mmio: 0xde000000 [ 80.653631] bttv0: detected: AVermedia AverTV DVB-T 771 [card=123], PCI subsystem ID is 1461:0771 [ 80.680278] bttv0: using: AVerMedia AVerTV DVB-T 771 [card=123,autodetected] [ 80.701453] bttv0: gpio: en=00000000, out=00000000 in=00f0ff0f [init] [ 80.710307] bttv0: using tuner=4 [ 80.738000] bttv0: registered device video0 [ 80.761531] bttv0: registered device vbi0 [ 80.773620] bttv0: PLL: 28636363 => 35468950 .. ok [ 80.817822] bttv0: add subdevice "dvb0" [ 80.830446] input: bttv IR (card=123) as /class/input/input1 [ 80.847471] bttv: Bt8xx card found (1). [ 80.859051] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 80.881365] bttv1: Bt878 (rev 17) at 0000:03:03.0, irq: 17, latency: 32, mmio: 0xde002000 [ 80.906086] bttv1: detected: AverMedia AverTV DVB-T 761 [card=124], PCI subsystem ID is 1461:0761 [ 80.932724] bttv1: using: AverMedia AverTV DVB-T 761 [card=124,autodetected] [ 80.953898] bttv1: gpio: en=00000000, out=00000000 in=0098001d [init] [ 80.981234] bttv1: using tuner=-1 [ 80.991709] bttv1: registered device video1 [ 81.004726] bttv1: registered device vbi1 [ 81.016845] bttv1: PLL: 28636363 => 35468950 .. ok [ 81.062114] bttv1: add subdevice "dvb1" [ 81.074211] input: bttv IR (card=124) as /class/input/input2 [ 81.668041] bt878: AUDIO driver version 0.0.0 loaded [ 81.686728] bt878: Bt878 AUDIO function found (0). [ 81.701164] ACPI: PCI Interrupt 0000:03:02.1[A] -> GSI 22 (level, low) -> IRQ 21 [ 81.725015] bt878_probe: card id=[0x7711461],[ AVermedia AverTV DVB-T 771 ] has DVB functions. [ 81.750882] bt878(0): Bt878 (rev 17) at 03:02.1, irq: 21, latency: 32, memory: 0xde001000 [ 81.775688] bt878: Bt878 AUDIO function found (1). [ 81.790116] ACPI: PCI Interrupt 0000:03:03.1[A] -> GSI 16 (level, low) -> IRQ 17 [ 81.812414] bt878_probe: card id=[0x7611461],[ AverMedia AverTV DVB-T 761 ] has DVB functions. [ 81.838280] bt878(1): Bt878 (rev 17) at 03:03.1, irq: 17, latency: 32, memory: 0xde003000 [ 81.900780] btaudio: driver version 0.7 loaded [digital+analog] [ 85.217444] ieee1394: Initialized config rom entry `ip1394' [ 85.263009] ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 21 (level, low) -> IRQ 19 [ 85.337040] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[dd026000-dd0267ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 85.463229] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [ 85.965499] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA] [ 86.499177] gameport: NS558 PnP Gameport is pnp00:0f/gameport0, io 0x201, speed 701kHz [ 86.606247] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) [ 86.628635] Uniform CD-ROM driver Revision: 3.20 [ 86.690574] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d61000069d6eb] [ 86.816147] eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) [ 87.015794] e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex [ 89.674197] md: md0 stopped. [ 89.819759] md: bind<sdb1> [ 89.828088] md: bind<sdc1> [ 89.836415] md: bind<sdd1> [ 89.844766] md: bind<sde1> [ 89.853098] md: bind<sdf1> [ 89.861456] md: bind<sda1> [ 89.914296] raid5: automatically using best checksumming function: pIII_sse [ 89.939552] pIII_sse : 3920.000 MB/sec [ 89.952153] raid5: using function: pIII_sse (3920.000 MB/sec) [ 89.993445] raid6: int32x1 988 MB/s [ 90.021416] raid6: int32x2 1132 MB/s [ 90.049369] raid6: int32x4 796 MB/s [ 90.077326] raid6: int32x8 589 MB/s [ 90.105191] raid6: mmxx1 2480 MB/s [ 90.133135] raid6: mmxx2 3117 MB/s [ 90.161079] raid6: sse1x1 1628 MB/s [ 90.189003] raid6: sse1x2 2226 MB/s [ 90.216958] raid6: sse2x1 2707 MB/s [ 90.244899] raid6: sse2x2 3285 MB/s [ 90.256198] raid6: using algorithm sse2x2 (3285 MB/s) [ 90.271373] md: raid6 personality registered for level 6 [ 90.287328] md: raid5 personality registered for level 5 [ 90.303284] md: raid4 personality registered for level 4 [ 90.347889] raid5: device sda1 operational as raid disk 0 [ 90.364121] raid5: device sdf1 operational as raid disk 5 [ 90.380336] raid5: device sde1 operational as raid disk 4 [ 90.396548] raid5: device sdd1 operational as raid disk 3 [ 90.412761] raid5: device sdc1 operational as raid disk 2 [ 90.428974] raid5: device sdb1 operational as raid disk 1 [ 90.445627] raid5: allocated 6285kB for md0 [ 90.458220] raid5: raid level 5 set md0 active with 6 out of 6 devices, algorithm 2 [ 90.481224] RAID5 conf printout: [ 90.490952] --- rd:6 wd:6 [ 90.499126] disk 0, o:1, dev:sda1 [ 90.509372] disk 1, o:1, dev:sdb1 [ 90.519619] disk 2, o:1, dev:sdc1 [ 90.529865] disk 3, o:1, dev:sdd1 [ 90.540112] disk 4, o:1, dev:sde1 [ 90.550361] disk 5, o:1, dev:sdf1 [ 90.649441] kjournald starting. Commit interval 5 seconds [ 90.690035] EXT3 FS on md0, internal journal [ 90.702982] EXT3-fs: mounted filesystem with ordered data mode. [ 91.107326] i2c_adapter i2c-0: SMBus Quick command not supported, can't probe for chips [ 91.131381] i2c_adapter i2c-1: SMBus Quick command not supported, can't probe for chips [ 91.155422] i2c_adapter i2c-2: SMBus Quick command not supported, can't probe for chips [ 91.283721] it87: Found IT8712F chip at 0x290, revision 5 [ 96.057580] Real Time Clock Driver v1.12ac [ 96.205426] Intel 810 + AC97 Audio, version 1.01, 23:31:07 Feb 5 2007 [ 96.242132] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 96.242137] i810: Intel ICH5 found at IO 0xdc00 and 0xd800, MEM 0xde101000 and 0xde102000, IRQ 22 [ 96.268801] i810: Intel ICH5 mmio at 0xf89fe000 and 0xf8dbc000 [ 96.784549] i810_audio: Primary codec has ID 2 [ 96.797957] i810_audio: Audio Controller supports 6 channels. [ 96.815223] i810_audio: Defaulting to base 2 channel mode. [ 96.831697] i810_audio: Resetting connection 0 [ 96.845089] i810_audio: Connection 0 with codec id 2 [ 96.860307] ac97_codec: AC97 Audio codec, id: ALG128 (Unknown) [ 96.878457] i810_audio: AC'97 codec 2 Unable to map surround DAC's (or DAC's not present), total channels = 2 [ 97.008529] DVB: registering new adapter (bttv0). [ 97.050811] DVB: registering frontend 2 (Zarlink MT352 DVB-T)... [ 97.069515] DVB: registering new adapter (bttv1). [ 97.108013] DVB: registering frontend 3 (Spase SP887x DVB-T)... [ 97.393021] loop: loaded (max 8 devices) [ 97.544417] lp0: using parport0 (interrupt-driven). [ 97.559088] lp0: console ready [ 97.905756] input: ImPS/2 Generic Wheel Mouse as /class/input/input3 [ 1047.952036] nvidia: module license 'NVIDIA' taints kernel. [ 1048.231688] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 1048.231877] NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9746 Fri Dec 15 09:54:45 PST 2006 [ 1112.407498] NET: Registered protocol family 17 [ 1119.475697] sp887x: waiting for firmware upload (dvb-fe-sp887x.fw)... [ 1119.534157] i2c_adapter i2c-5: sendbytes: error - bailout. [ 1119.553329] sp887x_initial_setup: firmware upload... sp887x: firmware upload complete [ 1130.779962] NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9746 Fri Dec 15 09:54:45 PST 2006 [ 1130.945451] NVRM: not using NVAGP, an AGPGART backend is loaded! [ 1131.268568] **WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 1:00.0] forgot to specify physical device; fix it! [ 1131.301054] **WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 1:00.0] forgot to specify physical device; fix it! [ 1131.333422] **WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 1:00.0] forgot to specify physical device; fix it! [49609.535770] eth1: link down [50409.031625] eth1: link down [50458.173775] ACPI: PCI interrupt for device 0000:03:00.0 disabled [50462.568588] 8139too Fast Ethernet driver 0.9.28 [50462.582909] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16 [50462.606650] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16 [50462.626254] eth1: Identified 8139 chip type 'RTL-8100B/8139D' [50472.425379] eth1: link down [50838.942315] ISO 9660 Extensions: Microsoft Joliet Level 3 [50838.995065] ISOFS: changing to secondary root [51198.435469] Floppy drive(s): fd0 is 1.44M [51198.462259] FDC 0 is a post-1991 82077 [51652.134564] ACPI: PCI interrupt for device 0000:03:00.0 disabled [51654.752441] 8139too Fast Ethernet driver 0.9.28 [51654.766798] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16 [51654.790615] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16 [51654.810238] eth1: Identified 8139 chip type 'RTL-8100B/8139D' [51732.573984] eth1: link down [51869.230362] ACPI: PCI interrupt for device 0000:03:00.0 disabled [51882.055418] 8139too Fast Ethernet driver 0.9.28 [51882.069632] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16 [51882.093148] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16 [51882.112753] eth1: Identified 8139 chip type 'RTL-8100B/8139D' [51895.092156] eth1: link down [52712.676450] ACPI: PCI interrupt for device 0000:03:00.0 disabled [52746.611231] 8139too Fast Ethernet driver 0.9.28 [52746.625819] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 16 [52746.649500] eth1: RealTek RTL8139 at 0x8000, 00:40:f4:7c:01:da, IRQ 16 [52746.669126] eth1: Identified 8139 chip type 'RTL-8100B/8139D' [52777.548838] eth1: link up, 10Mbps, half-duplex, lpa 0x0000 [55943.661256] eth1: link down [55952.778841] eth1: link up, 10Mbps, half-duplex, lpa 0x0000 [59314.398192] eth1: link down [296878.789042] ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [296878.809072] ata6.00: cmd 25/00:b8:3f:c4:b6/00:00:20:00:00/e0 tag 0 cdb 0x0 data 94208 in [296878.809074] res 50/00:00:f6:c4:b6/00:00:00:00:00/e0 Emask 0x1 (device error) [296878.863463] ata6.00: configured for UDMA/133 [296878.876719] ata6: EH complete [296878.887916] SCSI device sdf: 625142448 512-byte hdwr sectors (320073 MB) [296878.908701] sdf: Write Protect is off [296878.920049] sdf: Mode Sense: 00 3a 00 00 [296878.920677] SCSI device sdf: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [372228.827897] md: data-check of RAID array md0 [372228.841009] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [372228.858753] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [372228.888177] md: using 128k window, over a total of 312568576 blocks. [373421.090148] md: md_do_sync() got signal ... exiting [373900.027346] md: data-check of RAID array md0 [373900.040476] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [373900.058225] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [373900.087655] md: using 128k window, over a total of 312568576 blocks. [373929.661179] md: md_do_sync() got signal ... exiting [373969.047667] md: data-check of RAID array md0 [373969.060784] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [373969.078514] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [373969.107934] md: using 128k window, over a total of 312568576 blocks. [373997.679790] md: md_do_sync() got signal ... exiting [374111.455742] md: data-check of RAID array md0 [374111.468859] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [374111.486591] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [374111.516027] md: using 128k window, over a total of 312568576 blocks. [374145.613884] md: md_do_sync() got signal ... exiting [375467.714751] md: data-check of RAID array md0 [375467.727800] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [375467.745564] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [375467.774975] md: using 128k window, over a total of 312568576 blocks. [375498.851782] md: md_do_sync() got signal ... exiting [389928.941718] md: data-check of RAID array md0 [389928.954836] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [389928.972583] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [389929.001997] md: using 128k window, over a total of 312568576 blocks. [390130.004529] md: md_do_sync() got signal ... exiting [391181.917633] md: data-check of RAID array md0 [391181.930751] md: minimum _guaranteed_ speed: 10000 KB/sec/disk. [391181.948746] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [391181.978165] md: using 128k window, over a total of 312568576 blocks. [391205.275923] md: md_do_sync() got signal ... exiting [391213.664075] md: data-check of RAID array md0 [391213.677230] md: minimum _guaranteed_ speed: 20000 KB/sec/disk. [391213.695230] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [391213.724652] md: using 128k window, over a total of 312568576 blocks. [391340.799459] md: md0: data-check done. [391348.542935] md: data-check of RAID array md0 [391348.556051] md: minimum _guaranteed_ speed: 30000 KB/sec/disk. [391348.574045] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [391348.603463] md: using 128k window, over a total of 312568576 blocks. [391439.310203] md: md0: data-check done. [391562.862444] md: data-check of RAID array md0 [391562.875572] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [391562.893564] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [391562.922991] md: using 128k window, over a total of 312568576 blocks. [391603.742930] md: md0: data-check done. [411544.708182] md: data-check of RAID array md0 [411544.721215] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [411544.739160] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [411544.768533] md: using 128k window, over a total of 312568576 blocks. [426348.923156] md: md0: data-check done. [426349.453805] RAID5 conf printout: [426349.463741] --- rd:6 wd:6 [426349.472101] disk 0, o:1, dev:sda1 [426349.482528] disk 1, o:1, dev:sdb1 [426349.492958] disk 2, o:1, dev:sdc1 [426349.503386] disk 3, o:1, dev:sdd1 [426349.513819] disk 4, o:1, dev:sde1 [426349.524257] disk 5, o:1, dev:sdf1 [927080.617744] md: data-check of RAID array md0 [927080.630783] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [927080.648734] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [927080.678103] md: using 128k window, over a total of 312568576 blocks. [937567.332751] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4190002 action 0x2 [937567.354094] ata3.00: cmd b0/d5:01:09:4f:c2/00:00:00:00:00/00 tag 0 cdb 0x0 data 512 in [937567.354096] res 51/04:83:45:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error) [937568.120783] ata3: soft resetting port [937568.282450] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [937568.306693] ata3.00: configured for UDMA/100 [937568.319733] ata3: EH complete [937568.361223] SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB) [937568.397207] sdc: Write Protect is off [937568.408620] sdc: Mode Sense: 00 3a 00 00 [937568.453522] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [941696.843935] md: md0: data-check done. [941697.246454] RAID5 conf printout: [941697.256366] --- rd:6 wd:6 [941697.264718] disk 0, o:1, dev:sda1 [941697.275146] disk 1, o:1, dev:sdb1 [941697.285575] disk 2, o:1, dev:sdc1 [941697.296003] disk 3, o:1, dev:sdd1 [941697.306432] disk 4, o:1, dev:sde1 [941697.316862] disk 5, o:1, dev:sdf1 [1530647.746383] md: data-check of RAID array md0 [1530647.759677] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [1530647.778041] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [1530647.807663] md: using 128k window, over a total of 312568576 blocks. [1545248.680745] md: md0: data-check done. [1545249.266727] RAID5 conf printout: [1545249.276930] --- rd:6 wd:6 [1545249.285542] disk 0, o:1, dev:sda1 [1545249.296228] disk 1, o:1, dev:sdb1 [1545249.306923] disk 2, o:1, dev:sdc1 [1545249.317613] disk 3, o:1, dev:sdd1 [1545249.328292] disk 4, o:1, dev:sde1 [1545249.338981] disk 5, o:1, dev:sdf1 [1561452.735032] EXT3 FS on md0, internal journal [1565135.454597] md: requested-resync of RAID array md0 [1565135.469550] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [1565135.487809] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for requested-resync. [1565135.519058] md: using 128k window, over a total of 312568576 blocks. [1571049.926138] CIFS VFS: server not responding [1571049.939827] CIFS VFS: No response for cmd 114 mid 2686 [1579922.620488] md: md0: requested-resync done. [1579923.081359] RAID5 conf printout: [1579923.091529] --- rd:6 wd:6 [1579923.100144] disk 0, o:1, dev:sda1 [1579923.110833] disk 1, o:1, dev:sdb1 [1579923.121517] disk 2, o:1, dev:sdc1 [1579923.132206] disk 3, o:1, dev:sdd1 [1579923.142894] disk 4, o:1, dev:sde1 [1579923.153582] disk 5, o:1, dev:sdf1 [1587189.769116] EXT3 FS on md0, internal journal [1601734.884903] md: data-check of RAID array md0 [1601734.898203] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [1601734.916490] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [1601734.946174] md: using 128k window, over a total of 312568576 blocks. [1616496.836088] md: md0: data-check done. [1616497.290429] RAID5 conf printout: [1616497.300607] --- rd:6 wd:6 [1616497.309218] disk 0, o:1, dev:sda1 [1616497.319909] disk 1, o:1, dev:sdb1 [1616497.330595] disk 2, o:1, dev:sdc1 [1616497.341281] disk 3, o:1, dev:sdd1 [1616497.351971] disk 4, o:1, dev:sde1 [1616497.362658] disk 5, o:1, dev:sdf1 [2134215.520301] md: data-check of RAID array md0 [2134215.533598] md: minimum _guaranteed_ speed: 24000 KB/sec/disk. [2134215.551817] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check. [2134215.581438] md: using 128k window, over a total of 312568576 blocks. [2148832.606937] md: md0: data-check done. [2148833.104971] RAID5 conf printout: [2148833.115150] --- rd:6 wd:6 [2148833.123777] disk 0, o:1, dev:sda1 [2148833.134474] disk 1, o:1, dev:sdb1 [2148833.145157] disk 2, o:1, dev:sdc1 [2148833.155845] disk 3, o:1, dev:sdd1 [2148833.166537] disk 4, o:1, dev:sde1 [2148833.177220] disk 5, o:1, dev:sdf1 [2277927.597019] CIFS VFS: No response for cmd 114 mid 2688
/dev/sda: ATA device, with non-removable media Model Number: WDC WD3200SD-01KNB0 Serial Number: WD-WCAMR1466102 Firmware Revision: 08.05J08 Standards: Supported: 6 5 4 3 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 625142448 device size with M = 1024*1024: 305245 MBytes device size with M = 1000*1000: 320072 MBytes (320 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase Checksum: correct /dev/sdb: ATA device, with non-removable media Model Number: WDC WD3200JD-00KLB0 Serial Number: WD-WMAMR1305763 Firmware Revision: 08.05J08 Standards: Supported: 6 5 4 3 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 625142448 device size with M = 1024*1024: 305245 MBytes device size with M = 1000*1000: 320072 MBytes (320 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase Checksum: correct /dev/sdc: ATA device, with non-removable media Model Number: WDC WD3200JD-00KLB0 Serial Number: WD-WCAMR1427570 Firmware Revision: 08.05J08 Standards: Supported: 6 5 4 3 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 625142448 device size with M = 1024*1024: 305245 MBytes device size with M = 1000*1000: 320072 MBytes (320 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 0 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase Checksum: correct /dev/sdd: ATA device, with non-removable media Model Number: WDC WD3200JD-00KLB0 Serial Number: WD-WMAMR1628424 Firmware Revision: 08.05J08 Standards: Supported: 6 5 4 3 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 625142448 device size with M = 1024*1024: 305245 MBytes device size with M = 1000*1000: 320072 MBytes (320 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 0 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase Checksum: correct /dev/sde: ATA device, with non-removable media Model Number: WDC WD3200SD-01KNB0 Serial Number: WD-WCAMR1470395 Firmware Revision: 08.05J08 Standards: Supported: 6 5 4 3 Likely used: 6 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 625142448 device size with M = 1024*1024: 305245 MBytes device size with M = 1000*1000: 320072 MBytes (320 GB) Capabilities: LBA, IORDY(can be disabled) bytes avail on r/w long: 4 Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 0 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase Checksum: correct /dev/sdf: ATA device, with non-removable media Model Number: WDC WD3200YS-01PGB0 Serial Number: WD-WCAPD3621822 Firmware Revision: 21.00M21 Standards: Supported: 7 6 5 4 Likely used: 7 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 625142448 device size with M = 1024*1024: 305245 MBytes device size with M = 1000*1000: 320072 MBytes (320 GB) Capabilities: LBA, IORDY(can be disabled) Queue depth: 1 Standby timer values: spec'd by Standard, with device specific minimum R/W multiple sector transfer: Max = 16 Current = 0 Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * NOP cmd * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set Automatic Acoustic Management feature set SET MAX security extension * SET FEATURES subcommand required to spinup after power up Power-Up In Standby feature set * DOWNLOAD MICROCODE cmd * General Purpose Logging feature set * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase Checksum: correct
/dev/sda: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200SD-01KNB0 Serial Number: WD-WCAMR1466102 Firmware Version: 08.05J08 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Mar 6 08:37:46 2007 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 185 185 021 Pre-fail Always - 5725 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 31 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 10957 10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 31 194 Temperature_Celsius 0x0022 112 096 000 Old_age Always - 38 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10884 - # 2 Extended offline Completed without error 00% 10717 - # 3 Extended offline Completed without error 00% 10548 - # 4 Extended offline Completed without error 00% 10377 - # 5 Extended offline Completed without error 00% 10209 - # 6 Extended offline Completed without error 00% 10041 - # 7 Extended offline Completed without error 00% 9874 - # 8 Extended offline Completed without error 00% 9706 - # 9 Extended offline Completed without error 00% 9538 - #10 Extended offline Completed without error 00% 9370 - #11 Extended offline Completed without error 00% 9202 - #12 Extended offline Completed without error 00% 9035 - #13 Extended offline Completed without error 00% 8867 - #14 Extended offline Completed without error 00% 8700 - #15 Extended offline Completed without error 00% 8532 - #16 Extended offline Completed without error 00% 8364 - #17 Extended offline Completed without error 00% 8196 - #18 Extended offline Completed without error 00% 8028 - #19 Extended offline Completed without error 00% 7861 - #20 Extended offline Completed without error 00% 241 - #21 Short offline Completed without error 00% 239 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. /dev/sdb: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200JD-00KLB0 Serial Number: WD-WMAMR1305763 Firmware Version: 08.05J08 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Mar 6 08:37:46 2007 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 186 185 021 Pre-fail Always - 5700 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 100 5 Reallocated_Sector_Ct 0x0033 195 195 140 Pre-fail Always - 35 7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 12292 10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 100 194 Temperature_Celsius 0x0022 110 089 000 Old_age Always - 40 196 Reallocated_Event_Count 0x0032 198 198 000 Old_age Always - 2 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 12220 - # 2 Extended offline Completed without error 00% 12052 - # 3 Extended offline Completed without error 00% 11884 - # 4 Extended offline Completed without error 00% 11712 - # 5 Extended offline Completed without error 00% 11545 - # 6 Extended offline Completed without error 00% 11377 - # 7 Extended offline Completed without error 00% 11209 - # 8 Extended offline Completed without error 00% 11041 - # 9 Extended offline Completed without error 00% 10874 - #10 Extended offline Completed without error 00% 10706 - #11 Extended offline Completed without error 00% 10538 - #12 Extended offline Completed without error 00% 10371 - #13 Extended offline Completed without error 00% 10203 - #14 Extended offline Completed without error 00% 10035 - #15 Extended offline Completed without error 00% 9867 - #16 Extended offline Completed without error 00% 9699 - #17 Extended offline Completed without error 00% 9531 - #18 Extended offline Completed without error 00% 9364 - #19 Extended offline Completed without error 00% 9196 - #20 Extended offline Completed without error 00% 1576 - #21 Conveyance offline Interrupted (host reset) 40% 1014 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. /dev/sdc: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200JD-00KLB0 Serial Number: WD-WCAMR1427570 Firmware Version: 08.05J08 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Mar 6 08:37:47 2007 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 195 186 021 Pre-fail Always - 5225 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 52 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 11180 10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 52 194 Temperature_Celsius 0x0022 110 095 000 Old_age Always - 40 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 665 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 11107 - # 2 Extended offline Completed without error 00% 10939 - # 3 Extended offline Completed without error 00% 10600 - # 4 Extended offline Completed without error 00% 10432 - # 5 Extended offline Completed without error 00% 10264 - # 6 Extended offline Completed without error 00% 10096 - # 7 Extended offline Completed without error 00% 9929 - # 8 Extended offline Completed without error 00% 9761 - # 9 Extended offline Completed without error 00% 9593 - #10 Extended offline Completed without error 00% 9425 - #11 Extended offline Completed without error 00% 9258 - #12 Extended offline Completed without error 00% 9090 - #13 Extended offline Completed without error 00% 8922 - #14 Extended offline Completed without error 00% 8755 - #15 Extended offline Completed without error 00% 8587 - #16 Extended offline Completed without error 00% 8419 - #17 Extended offline Completed without error 00% 8251 - #18 Conveyance offline Completed without error 00% 8098 - #19 Extended offline Completed without error 00% 8084 - #20 Extended offline Completed without error 00% 463 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. /dev/sdd: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200JD-00KLB0 Serial Number: WD-WMAMR1628424 Firmware Version: 08.05J08 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Mar 6 08:37:47 2007 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 191 190 021 Pre-fail Always - 5450 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 85 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 11915 10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 85 194 Temperature_Celsius 0x0022 109 095 000 Old_age Always - 41 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 283 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 11842 - # 2 Extended offline Completed without error 00% 11674 - # 3 Extended offline Completed without error 00% 11506 - # 4 Extended offline Completed without error 00% 11335 - # 5 Extended offline Completed without error 00% 11167 - # 6 Extended offline Completed without error 00% 10999 - # 7 Extended offline Completed without error 00% 10831 - # 8 Extended offline Completed without error 00% 10664 - # 9 Extended offline Completed without error 00% 10495 - #10 Extended offline Completed without error 00% 10328 - #11 Extended offline Completed without error 00% 10160 - #12 Extended offline Completed without error 00% 9993 - #13 Extended offline Completed without error 00% 9825 - #14 Extended offline Completed without error 00% 9657 - #15 Extended offline Completed without error 00% 9490 - #16 Extended offline Completed without error 00% 9322 - #17 Extended offline Completed without error 00% 9154 - #18 Extended offline Completed without error 00% 8986 - #19 Conveyance offline Completed without error 00% 8833 - #20 Extended offline Completed without error 00% 8819 - #21 Extended offline Completed without error 00% 1198 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. /dev/sde: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200SD-01KNB0 Serial Number: WD-WCAMR1470395 Firmware Version: 08.05J08 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Mar 6 08:37:47 2007 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 116) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 188 188 021 Pre-fail Always - 5558 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 38 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10269 10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 38 194 Temperature_Celsius 0x0022 111 090 000 Old_age Always - 39 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10196 - # 2 Extended offline Completed without error 00% 10028 - # 3 Extended offline Completed without error 00% 9861 - # 4 Extended offline Completed without error 00% 9689 - # 5 Extended offline Completed without error 00% 9521 - # 6 Extended offline Completed without error 00% 9353 - # 7 Extended offline Completed without error 00% 9186 - # 8 Extended offline Completed without error 00% 9018 - # 9 Extended offline Completed without error 00% 8850 - #10 Extended offline Completed without error 00% 8682 - #11 Extended offline Completed without error 00% 8514 - #12 Extended offline Completed without error 00% 8347 - #13 Extended offline Completed without error 00% 8179 - #14 Extended offline Completed without error 00% 8011 - #15 Extended offline Completed without error 00% 7844 - #16 Extended offline Completed without error 00% 7676 - #17 Extended offline Completed without error 00% 7508 - #18 Extended offline Completed without error 00% 7340 - #19 Extended offline Completed without error 00% 7173 - #20 Extended offline Completed without error 00% 241 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. /dev/sdf: smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200YS-01PGB0 Serial Number: WD-WCAPD3621822 Firmware Version: 21.00M21 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Tue Mar 6 08:37:47 2007 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (9600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 111) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 100 253 021 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 4 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 712 10 Spin_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0013 100 253 051 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3 190 Unknown_Attribute 0x0022 062 044 000 Old_age Always - 38 194 Temperature_Celsius 0x0022 112 095 000 Old_age Always - 38 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 640 - # 2 Extended offline Completed without error 00% 472 - # 3 Extended offline Completed without error 00% 304 - # 4 Extended offline Completed without error 00% 133 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.