I posted a patch to the IDE list yesterday for testing which performs the
workarounds the old IDE layer does for this. I'll forward you a copy
I applied the patch, but unfortunately I get the same error messages
as before and the drive doesn't work.
Regards,
Nils
Linux version 2.6.20-rc6-mm3 (root@h55a207-4) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Sat Feb 3 14:54:21 CET 2007
Command line: root=/dev/sda2 ro
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 262128) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.2 present.
ACPI: RSDP @ 0x00000000000f9050/0x0014 (v000 VIAK8 )
ACPI: RSDT @ 0x000000003fff3000/0x002C (v001 VIAK8 AWRDACPI 0x42302E31 AWRD 0x00000000)
ACPI: FACP @ 0x000000003fff3040/0x0074 (v001 VIAK8 AWRDACPI 0x42302E31 AWRD 0x00000000)
ACPI: DSDT @ 0x000000003fff30c0/0x5573 (v001 VIAK8 AWRDACPI 0x00001000 MSFT 0x0100000E)
ACPI: FACS @ 0x000000003fff0000/0x0040
ACPI: APIC @ 0x000000003fff8640/0x005A (v001 VIAK8 AWRDACPI 0x42302E31 AWRD 0x00000000)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 262128) 1 entries of 256 used
sizeof(struct page) = 56
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 262128
On node 0 totalpages: 262031
Node 0 memmap at 0xffff810001000000 size 14680064 first pfn 0xffff810001000000
DMA zone: 56 pages used for memmap
DMA zone: 885 pages reserved
DMA zone: 3058 pages, LIFO batch:0
DMA32 zone: 3527 pages used for memmap
DMA32 zone: 254505 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists. Total pages: 257563
Kernel command line: root=/dev/sda2 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 2211.032 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
CPU 0: aperture @ d8000000 size 128 MB
Memory: 1028264k/1048512k available (2112k kernel code, 19484k reserved, 886k data, 204k init)
Calibrating delay using timer specific routine.. 4426.84 BogoMIPS (lpj=8853693)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12562706
Detected 12.562 MHz APIC timer.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 *12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
NET: Registered protocol family 8
NET: Registered protocol family 20
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xd8000000
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e8000000-e9ffffff
PREFETCH window: e0000000-e7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Linux agpgart interface v0.102 (c) Dave Jones
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
sata_sil 0000:00:0e.0: version 2.0
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 18 (level, low) -> IRQ 18
ata1: SATA max UDMA/100 cmd 0xFFFFC20000010080 ctl 0xFFFFC2000001008A bmdma 0xFFFFC20000010000 irq 18
ata2: SATA max UDMA/100 cmd 0xFFFFC200000100C0 ctl 0xFFFFC200000100CA bmdma 0xFFFFC20000010008 irq 18
ata3: SATA max UDMA/100 cmd 0xFFFFC20000010280 ctl 0xFFFFC2000001028A bmdma 0xFFFFC20000010200 irq 18
ata4: SATA max UDMA/100 cmd 0xFFFFC200000102C0 ctl 0xFFFFC200000102CA bmdma 0xFFFFC20000010208 irq 18
scsi0 : sata_sil
ata1: SATA link down (SStatus 0 SControl 310)
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi2 : sata_sil
ata3: SATA link down (SStatus 0 SControl 310)
scsi3 : sata_sil
ata4: SATA link down (SStatus 0 SControl 310)
sata_via 0000:00:0f.0: version 2.0
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 11
ata5: SATA max UDMA/133 cmd 0xD600 ctl 0xD702 bmdma 0xDA00 irq 20
ata6: SATA max UDMA/133 cmd 0xD800 ctl 0xD902 bmdma 0xDA08 irq 20
scsi4 : sata_via
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ATA: abnormal status 0x7F on port 0xD607
ATA: abnormal status 0x7F on port 0xD607
ata5.00: ATA-7, max UDMA/133, 398297088 sectors: LBA48
ata5.00: ata5: dev 0 multi count 16
ata5.00: configured for UDMA/133
scsi5 : sata_via
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: ATAPI, max UDMA/33
ata6.00: configured for UDMA/33
scsi 4:0:0:0: Direct-Access ATA Maxtor 6Y200M0 YAR5 PQ: 0 ANSI: 5
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 4:0:0:0: Attached scsi disk sda
scsi 5:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183A SB02 PQ: 0 ANSI: 5
serio: i8042 KBD port at 0x60,0x64 irq 1
TCP cubic registered
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
ReiserFS: sda2: found reiserfs format "3.6" with standard journal
ReiserFS: sda2: using ordered data mode
ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda2: checking transaction log (sda2)
ReiserFS: sda2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
NET: Registered protocol family 1
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 5:0:0:0: Attached scsi CD-ROM sr0
sd 4:0:0:0: Attached scsi generic sg0 type 0
sr 5:0:0:0: Attached scsi generic sg1 type 5
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
USB Universal Host Controller Interface driver v3.0
input: PC Speaker as /class/input/input0
Probing IDE interface ide1...
ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: 3Com Gigabit LOM (3C940)
PrefPort:A RlmtMode:Check Link State
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000dd00
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.20-rc6-mm3 uhci_hcd
usb usb1: SerialNumber: 0000:00:10.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000de00
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.20-rc6-mm3 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000df00
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.20-rc6-mm3 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000e000
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.20-rc6-mm3 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.3
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 21, io mem 0xea084000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.20-rc6-mm3 ehci_hcd
usb usb5: SerialNumber: 0000:00:10.4
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 1-1: device not accepting address 2, error -71
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: new device found, idVendor=045e, idProduct=0025
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: Microsoft IntelliMouse ® with IntelliEye
usb 1-1: Manufacturer: Microsoft
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new low speed USB device using uhci_hcd and address 5
usb 1-2: new device found, idVendor=0419, idProduct=8002
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: Sam Sung Electronics
usb 1-2: Manufacturer: Samsung Electronics
usb 1-2: SerialNumber: 1234
usb 1-2: configuration #1 chosen from 1 choice
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: new device found, idVendor=045e, idProduct=00dd
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: Comfort Curve Keyboard 2000
usb 2-1: Manufacturer: Microsoft
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft IntelliMouse ® with IntelliEye as /class/input/input1
input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse ® with IntelliEye] on usb-0000:00:10.0-1
hiddev96: USB HID v1.10 Device [Samsung Electronics Sam Sung Electronics] on usb-0000:00:10.0-2
input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input2
input: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:10.1-1
input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input3
input: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:10.1-1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata6.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata6: soft resetting port
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: configured for UDMA/33
ata6: EH complete
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata6.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata6: soft resetting port
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: configured for UDMA/33
ata6: EH complete
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata6.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata6: soft resetting port
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: configured for UDMA/33
ata6: EH complete
ata6.00: limiting speed to UDMA/25
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata6.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata6: soft resetting port
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: configured for UDMA/25
ata6: EH complete
sr0: CDROM (ioctl) error, command: <6>Read TOC/PMA/ATIP 43 00 00 00 00 00 00 00 0c 40
sr: Current [descriptor]: sense key: Aborted Command
Additional sense: No additional sense information
ata6.00: limiting speed to UDMA/16
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata6.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata6: soft resetting port
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: configured for UDMA/16
ata6: EH complete
Adding 2008112k swap on /dev/sda3. Priority:-1 extents:1 across:2008112k
ata6.00: limiting speed to PIO4
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata6.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata6: soft resetting port
ATA: abnormal status 0x7F on port 0xD807
ATA: abnormal status 0x7F on port 0xD807
ata6.00: configured for PIO4
ata6: EH complete
Probing IDE interface ide0...
Probing IDE interface ide1...
ReiserFS: sda6: found reiserfs format "3.6" with standard journal
ReiserFS: sda6: using ordered data mode
ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda6: checking transaction log (sda6)
ReiserFS: sda6: Using r5 hash to sort names
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: Using r5 hash to sort names
ReiserFS: sda8: found reiserfs format "3.6" with standard journal
ReiserFS: sda8: using ordered data mode
ReiserFS: sda8: journal params: device sda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda8: checking transaction log (sda8)
ReiserFS: sda8: Using r5 hash to sort names
ReiserFS: sda7: found reiserfs format "3.6" with standard journal
ReiserFS: sda7: using ordered data mode
ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda7: checking transaction log (sda7)
ReiserFS: sda7: Using r5 hash to sort names
NET: Registered protocol family 17
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: none
irq moderation: disabled
scatter-gather: disabled
tx-checksum: disabled
rx-checksum: disabled
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (35 C)
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
parport0: Printer, HEWLETT-PACKARD DESKJET 710C
lp0: using parport0 (polling).
ppdev: user-space parallel port driver
eth0: no IPv6 routers present
