Hi Sven,
> I am having problems to access a hard drive connected to a SIS180
> SATA-RAID controller.
>
> The controller is located on my mainboard (Elitegroup KV2 extreme).
> There is only one hard disk drive connected to the PATA port od the
> controller. Both SATA ports are empty. The BIOS of the controller
> recognizes the disk and while running Microsoft Windows I can access the
> disk.
>
I include the actual drivers for testing. You must use a kernel
2.6.19 or higher.
The PATA support for the SiS180 chip is done by the pata_sis
driver. You must enable
the PATA_SIS support in the .config. Exchange the files in drivers/ata
with the files from attachement.
feeback wanted.
regards,
Uwe
/*
* pata_sis.c - SiS ATA driver
*
* (C) 2005 Red Hat <alan@xxxxxxxxxx>
*
* Based upon linux/drivers/ide/pci/sis5513.c
* Copyright (C) 1999-2000 Andre Hedrick <andre@xxxxxxxxxxxxx>
* Copyright (C) 2002 Lionel Bouton <Lionel.Bouton@xxxxxxxx>, Maintainer
* Copyright (C) 2003 Vojtech Pavlik <vojtech@xxxxxxx>
* SiS Taiwan : for direct support and hardware.
* Daniela Engert : for initial ATA100 advices and numerous others.
* John Fremlin, Manfred Spraul, Dave Morgan, Peter Kjellerstedt :
* for checking code correctness, providing patches.
* Original tests and design on the SiS620 chipset.
* ATA100 tests and design on the SiS735 chipset.
* ATA16/33 support from specs
* ATA133 support for SiS961/962 by L.C. Chang <lcchang@xxxxxxxxxx>
*
*
* TODO
* Check MWDMA on drives that don't support MWDMA speed pio cycles ?
* More Testing
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>
#define DRV_NAME "pata_sis"
#define DRV_VERSION "0.4.5"
struct sis_chipset {
u16 device; /* PCI host ID */
struct ata_port_info *info; /* Info block */
/* Probably add family, cable detect type etc here to clean
up code later */
};
/**
* sis_port_base - return PCI configuration base for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
* number.
*/
static int sis_port_base(struct ata_device *adev)
{
return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno);
}
/**
* sis_133_pre_reset - check for 40/80 pin
* @ap: Port
*
* Perform cable detection for the later UDMA133 capable
* SiS chipset.
*/
static int sis_133_pre_reset(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 tmp;
/* The top bit of this register is the cable detect bit */
pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp);
if (tmp & 0x8000)
ap->cbl = ATA_CBL_PATA40;
else
ap->cbl = ATA_CBL_PATA80;
return ata_std_prereset(ap);
}
/**
* sis_error_handler - Probe specified port on PATA host controller
* @ap: Port to probe
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_133_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, sis_133_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* sis_66_pre_reset - check for 40/80 pin
* @ap: Port
*
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
* SiS IDE controllers.
*/
static int sis_66_pre_reset(struct ata_port *ap)
{
static const struct pci_bits sis_enable_bits[] = {
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
{ 0x4aU, 1U, 0x04UL, 0x04UL } /* port 1 */
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 tmp;
if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
ata_port_disable(ap);
printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
return 0;
}
/* Older chips keep cable detect in bits 4/5 of reg 0x48 */
pci_read_config_byte(pdev, 0x48, &tmp);
tmp >>= ap->port_no;
if (tmp & 0x10)
ap->cbl = ATA_CBL_PATA40;
else
ap->cbl = ATA_CBL_PATA80;
return ata_std_prereset(ap);
}
/**
* sis_66_error_handler - Probe specified port on PATA host controller
* @ap: Port to probe
* @classes:
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_66_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, sis_66_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* sis_old_pre_reset - probe begin
* @ap: ATA port
*
* Set up cable type and use generic probe init
*/
static int sis_old_pre_reset(struct ata_port *ap)
{
static const struct pci_bits sis_enable_bits[] = {
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
{ 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no])) {
ata_port_disable(ap);
printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
return 0;
}
ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
/**
* sis_old_error_handler - Probe specified port on PATA host controller
* @ap: Port to probe
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_old_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, sis_old_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* sis_set_fifo - Set RWP fifo bits for this device
* @ap: Port
* @adev: Device
*
* SIS chipsets implement prefetch/postwrite bits for each device
* on both channels. This functionality is not ATAPI compatible and
* must be configured according to the class of device present
*/
static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 fifoctrl;
u8 mask = 0x11;
mask <<= (2 * ap->port_no);
mask <<= adev->devno;
/* This holds various bits including the FIFO control */
pci_read_config_byte(pdev, 0x4B, &fifoctrl);
fifoctrl &= ~mask;
/* Enable for ATA (disk) only */
if (adev->class == ATA_DEV_ATA)
fifoctrl |= mask;
pci_write_config_byte(pdev, 0x4B, fifoctrl);
}
/**
* sis_old_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
* Set PIO mode for device, in host controller PCI config space. This
* function handles PIO set up for all chips that are pre ATA100 and
* also early ATA100 devices.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = sis_port_base(adev);
u8 t1, t2;
int speed = adev->pio_mode - XFER_PIO_0;
const u8 active[] = { 0x00, 0x07, 0x04, 0x03, 0x01 };
const u8 recovery[] = { 0x00, 0x06, 0x04, 0x03, 0x03 };
sis_set_fifo(ap, adev);
pci_read_config_byte(pdev, port, &t1);
pci_read_config_byte(pdev, port + 1, &t2);
t1 &= ~0x0F; /* Clear active/recovery timings */
t2 &= ~0x07;
t1 |= active[speed];
t2 |= recovery[speed];
pci_write_config_byte(pdev, port, t1);
pci_write_config_byte(pdev, port + 1, t2);
}
/**
* sis_100_set_pioode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
* Set PIO mode for device, in host controller PCI config space. This
* function handles PIO set up for ATA100 devices and early ATA133.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = sis_port_base(adev);
int speed = adev->pio_mode - XFER_PIO_0;
const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
sis_set_fifo(ap, adev);
pci_write_config_byte(pdev, port, actrec[speed]);
}
/**
* sis_133_set_pioode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: Device we are configuring for.
*
* Set PIO mode for device, in host controller PCI config space. This
* function handles PIO set up for the later ATA133 devices.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int port = 0x40;
u32 t1;
u32 reg54;
int speed = adev->pio_mode - XFER_PIO_0;
const u32 timing133[] = {
0x28269000, /* Recovery << 24 | Act << 16 | Ini << 12 */
0x0C266000,
0x04263000,
0x0C0A3000,
0x05093000
};
const u32 timing100[] = {
0x1E1C6000, /* Recovery << 24 | Act << 16 | Ini << 12 */
0x091C4000,
0x031C2000,
0x09072000,
0x04062000
};
sis_set_fifo(ap, adev);
/* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
pci_read_config_dword(pdev, 0x54, ®54);
if (reg54 & 0x40000000)
port = 0x70;
port += 8 * ap->port_no + 4 * adev->devno;
pci_read_config_dword(pdev, port, &t1);
t1 &= 0xC0C00FFF; /* Mask out timing */
if (t1 & 0x08) /* 100 or 133 ? */
t1 |= timing133[speed];
else
t1 |= timing100[speed];
pci_write_config_byte(pdev, port, t1);
}
/**
* sis_old_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
* Handles pre UDMA and UDMA33 devices. Supports MWDMA as well unlike
* the old ide/pci driver.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
const u16 udma_bits[] = { 0xE000, 0xC000, 0xA000 };
pci_read_config_word(pdev, drive_pci, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device */
timing &= ~ 0x870F;
timing |= mwdma_bits[speed];
pci_write_config_word(pdev, drive_pci, timing);
} else {
/* Bit 15 is UDMA on/off, bit 13-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x6000;
timing |= udma_bits[speed];
}
}
/**
* sis_66_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
* Handles UDMA66 and early UDMA100 devices. Supports MWDMA as well unlike
* the old ide/pci driver.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
const u16 udma_bits[] = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000};
pci_read_config_word(pdev, drive_pci, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device, bit 15 udma */
timing &= ~ 0x870F;
timing |= mwdma_bits[speed];
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x6000;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
}
/**
* sis_100_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
* Handles UDMA66 and early UDMA100 devices.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_port_base(adev);
u16 timing;
const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
pci_read_config_word(pdev, drive_pci, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x0F00;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
}
/**
* sis_133_early_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
* Handles early SiS 961 bridges. Supports MWDMA as well unlike
* the old ide/pci driver.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int drive_pci = sis_port_base(adev);
u16 timing;
const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
pci_read_config_word(pdev, drive_pci, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
timing &= ~0x0F00;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
}
/**
* sis_133_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
* Handles early SiS 961 bridges. Supports MWDMA as well unlike
* the old ide/pci driver.
*
* LOCKING:
* None (inherited from caller).
*/
static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
int port = 0x40;
u32 t1;
u32 reg54;
/* bits 4- cycle time 8 - cvs time */
const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
/* If bit 14 is set then the registers are mapped at 0x70 not 0x40 */
pci_read_config_dword(pdev, 0x54, ®54);
if (reg54 & 0x40000000)
port = 0x70;
port += (8 * ap->port_no) + (4 * adev->devno);
pci_read_config_dword(pdev, port, &t1);
if (adev->dma_mode < XFER_UDMA_0) {
t1 &= ~0x00000004;
/* FIXME: need data sheet to add MWDMA here. Also lacking on
ide/pci driver */
} else {
speed = adev->dma_mode - XFER_UDMA_0;
/* if & 8 no UDMA133 - need info for ... */
t1 &= ~0x00000FF0;
t1 |= 0x00000004;
if (t1 & 0x08)
t1 |= timing_u133[speed];
else
t1 |= timing_u100[speed];
}
pci_write_config_dword(pdev, port, t1);
}
static struct scsi_host_template sis_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations sis_133_ops = {
.port_disable = ata_port_disable,
.set_piomode = sis_133_set_piomode,
.set_dmamode = sis_133_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = sis_133_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_133_early_ops = {
.port_disable = ata_port_disable,
.set_piomode = sis_100_set_piomode,
.set_dmamode = sis_133_early_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = sis_66_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_100_ops = {
.port_disable = ata_port_disable,
.set_piomode = sis_100_set_piomode,
.set_dmamode = sis_100_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = sis_66_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_66_ops = {
.port_disable = ata_port_disable,
.set_piomode = sis_old_set_piomode,
.set_dmamode = sis_66_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = sis_66_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop,
};
static const struct ata_port_operations sis_old_ops = {
.port_disable = ata_port_disable,
.set_piomode = sis_old_set_piomode,
.set_dmamode = sis_old_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = sis_old_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop,
};
static struct ata_port_info sis_info = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07,
.udma_mask = 0,
.port_ops = &sis_old_ops,
};
static struct ata_port_info sis_info33 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07,
.udma_mask = ATA_UDMA2, /* UDMA 33 */
.port_ops = &sis_old_ops,
};
static struct ata_port_info sis_info66 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &sis_66_ops,
};
static struct ata_port_info sis_info100 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA5,
.port_ops = &sis_100_ops,
};
static struct ata_port_info sis_info100_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.udma_mask = ATA_UDMA5,
.pio_mask = 0x1f, /* pio0-4 */
.port_ops = &sis_66_ops,
};
struct ata_port_info sis_info133 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_ops,
};
static struct ata_port_info sis_info133_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_early_ops,
};
/* Privately shared with the SiS180 SATA driver, not for use elsewhere */
EXPORT_SYMBOL_GPL(sis_info133);
static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
{
u16 regw;
u8 reg;
if (sis->info == &sis_info133) {
pci_read_config_word(pdev, 0x50, ®w);
if (regw & 0x08)
pci_write_config_word(pdev, 0x50, regw & ~0x08);
pci_read_config_word(pdev, 0x52, ®w);
if (regw & 0x08)
pci_write_config_word(pdev, 0x52, regw & ~0x08);
return;
}
if (sis->info == &sis_info133_early || sis->info == &sis_info100) {
/* Fix up latency */
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
/* Set compatibility bit */
pci_read_config_byte(pdev, 0x49, ®);
if (!(reg & 0x01))
pci_write_config_byte(pdev, 0x49, reg | 0x01);
return;
}
if (sis->info == &sis_info66 || sis->info == &sis_info100_early) {
/* Fix up latency */
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
/* Set compatibility bit */
pci_read_config_byte(pdev, 0x52, ®);
if (!(reg & 0x04))
pci_write_config_byte(pdev, 0x52, reg | 0x04);
return;
}
if (sis->info == &sis_info33) {
pci_read_config_byte(pdev, PCI_CLASS_PROG, ®);
if (( reg & 0x0F ) != 0x00)
pci_write_config_byte(pdev, PCI_CLASS_PROG, reg & 0xF0);
/* Fall through to ATA16 fixup below */
}
if (sis->info == &sis_info || sis->info == &sis_info33) {
/* force per drive recovery and active timings
needed on ATA_33 and below chips */
pci_read_config_byte(pdev, 0x52, ®);
if (!(reg & 0x08))
pci_write_config_byte(pdev, 0x52, reg|0x08);
return;
}
BUG();
}
/**
* sis_init_one - Register SiS ATA PCI device with kernel services
* @pdev: PCI device to register
* @ent: Entry in sis_pci_tbl matching with @pdev
*
* Called from kernel PCI layer. We probe for combined mode (sigh),
* and then hand over control to libata, for it to do the rest.
*
* LOCKING:
* Inherited from PCI layer (may sleep).
*
* RETURNS:
* Zero on success, or -ERRNO value.
*/
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
static struct ata_port_info *port_info[2];
struct ata_port_info *port;
struct pci_dev *host = NULL;
struct sis_chipset *chipset = NULL;
static struct sis_chipset sis_chipsets[] = {
{ 0x0968, &sis_info133 },
{ 0x0966, &sis_info133 },
{ 0x0965, &sis_info133 },
{ 0x0745, &sis_info100 },
{ 0x0735, &sis_info100 },
{ 0x0733, &sis_info100 },
{ 0x0635, &sis_info100 },
{ 0x0633, &sis_info100 },
{ 0x0730, &sis_info100_early }, /* 100 with ATA 66 layout */
{ 0x0550, &sis_info100_early }, /* 100 with ATA 66 layout */
{ 0x0640, &sis_info66 },
{ 0x0630, &sis_info66 },
{ 0x0620, &sis_info66 },
{ 0x0540, &sis_info66 },
{ 0x0530, &sis_info66 },
{ 0x5600, &sis_info33 },
{ 0x5598, &sis_info33 },
{ 0x5597, &sis_info33 },
{ 0x5591, &sis_info33 },
{ 0x5582, &sis_info33 },
{ 0x5581, &sis_info33 },
{ 0x5596, &sis_info },
{ 0x5571, &sis_info },
{ 0x5517, &sis_info },
{ 0x5511, &sis_info },
{0}
};
static struct sis_chipset sis133_early = {
0x0, &sis_info133_early
};
static struct sis_chipset sis133 = {
0x0, &sis_info133
};
static struct sis_chipset sis100_early = {
0x0, &sis_info100_early
};
static struct sis_chipset sis100 = {
0x0, &sis_info100
};
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
/* We have to find the bridge first */
for (chipset = &sis_chipsets[0]; chipset->device; chipset++) {
host = pci_get_device(PCI_VENDOR_ID_SI, chipset->device, NULL);
if (host != NULL) {
if (chipset->device == 0x630) { /* SIS630 */
u8 host_rev;
pci_read_config_byte(host, PCI_REVISION_ID, &host_rev);
if (host_rev >= 0x30) /* 630 ET */
chipset = &sis100_early;
}
break;
}
}
/* Look for concealed bridges */
if (host == NULL) {
/* Second check */
u32 idemisc;
u16 trueid;
/* Disable ID masking and register remapping then
see what the real ID is */
pci_read_config_dword(pdev, 0x54, &idemisc);
pci_write_config_dword(pdev, 0x54, idemisc & 0x7fffffff);
pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
pci_write_config_dword(pdev, 0x54, idemisc);
switch(trueid) {
case 0x5518: /* SIS 962/963 */
chipset = &sis133;
if ((idemisc & 0x40000000) == 0) {
pci_write_config_dword(pdev, 0x54, idemisc | 0x40000000);
printk(KERN_INFO "SIS5513: Switching to 5513 register mapping\n");
}
break;
case 0x0180: /* SIS 965/965L */
chipset = &sis133;
break;
case 0x1180: /* SIS 966/966L */
chipset = &sis133;
break;
}
}
/* Further check */
if (chipset == NULL) {
struct pci_dev *lpc_bridge;
u16 trueid;
u8 prefctl;
u8 idecfg;
u8 sbrev;
/* Try the second unmasking technique */
pci_read_config_byte(pdev, 0x4a, &idecfg);
pci_write_config_byte(pdev, 0x4a, idecfg | 0x10);
pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
pci_write_config_byte(pdev, 0x4a, idecfg);
switch(trueid) {
case 0x5517:
lpc_bridge = pci_get_slot(pdev->bus, 0x10); /* Bus 0 Dev 2 Fn 0 */
if (lpc_bridge == NULL)
break;
pci_read_config_byte(lpc_bridge, PCI_REVISION_ID, &sbrev);
pci_read_config_byte(pdev, 0x49, &prefctl);
pci_dev_put(lpc_bridge);
if (sbrev == 0x10 && (prefctl & 0x80)) {
chipset = &sis133_early;
break;
}
chipset = &sis100;
break;
}
}
pci_dev_put(host);
/* No chipset info, no support */
if (chipset == NULL)
return -ENODEV;
port = chipset->info;
port->private_data = chipset;
sis_fixup(pdev, chipset);
port_info[0] = port_info[1] = port;
return ata_pci_init_one(pdev, port_info, 2);
}
static const struct pci_device_id sis_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
{ PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
{ }
};
static struct pci_driver sis_pci_driver = {
.name = DRV_NAME,
.id_table = sis_pci_tbl,
.probe = sis_init_one,
.remove = ata_pci_remove_one,
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
};
static int __init sis_init(void)
{
return pci_register_driver(&sis_pci_driver);
}
static void __exit sis_exit(void)
{
pci_unregister_driver(&sis_pci_driver);
}
module_init(sis_init);
module_exit(sis_exit);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
MODULE_VERSION(DRV_VERSION);
/*
* sata_sis.c - Silicon Integrated Systems SATA
*
* Maintained by: Uwe Koziolek
* Please ALWAYS copy linux-ide@xxxxxxxxxxxxxxx
* on emails.
*
* Copyright 2004 Uwe Koziolek
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* Hardware documentation available under NDA.
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "sata_sis"
#define DRV_VERSION "0.7"
enum {
sis_180 = 0,
SIS_SCR_PCI_BAR = 5,
/* PCI configuration registers */
SIS_GENCTL = 0x54, /* IDE General Control register */
SIS_SCR_BASE = 0xc0, /* sata0 phy SCR registers */
SIS180_SATA1_OFS = 0x10, /* offset from sata0->sata1 phy regs */
SIS182_SATA1_OFS = 0x20, /* offset from sata0->sata1 phy regs */
SIS_PMR = 0x90, /* port mapping register */
SIS_PMR_COMBINED = 0x30,
/* random bits */
SIS_FLAG_CFGSCR = (1 << 30), /* host flag: SCRs via PCI cfg */
GENCTL_IOMAPPED_SCR = (1 << 26), /* if set, SCRs are in IO space */
};
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
static const struct pci_device_id sis_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x0180), sis_180 }, /* SiS 964/180 */
{ PCI_VDEVICE(SI, 0x0181), sis_180 }, /* SiS 964/180 */
{ PCI_VDEVICE(SI, 0x0182), sis_180 }, /* SiS 965/965L */
{ PCI_VDEVICE(SI, 0x0183), sis_180 }, /* SiS 965/965L */
{ PCI_VDEVICE(SI, 0x1182), sis_180 }, /* SiS 966/966L */
{ PCI_VDEVICE(SI, 0x1183), sis_180 }, /* SiS 966/966L */
{ } /* terminate list */
};
static struct pci_driver sis_pci_driver = {
.name = DRV_NAME,
.id_table = sis_pci_tbl,
.probe = sis_init_one,
.remove = ata_pci_remove_one,
};
static struct scsi_host_template sis_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = ATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
static const struct ata_port_operations sis_ops = {
.port_disable = ata_port_disable,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.scr_read = sis_scr_read,
.scr_write = sis_scr_write,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop,
};
static struct ata_port_info sis_port_info = {
.sht = &sis_sht,
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
.pio_mask = 0x1f,
.mwdma_mask = 0x7,
.udma_mask = 0x7f,
.port_ops = &sis_ops,
};
#ifdef CONFIG_PATA_SIS
extern struct ata_port_info sis_info133;
#endif
MODULE_AUTHOR("Uwe Koziolek");
MODULE_DESCRIPTION("low-level driver for Silicon Integratad Systems SATA controller");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
MODULE_VERSION(DRV_VERSION);
static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned int addr = SIS_SCR_BASE + (4 * sc_reg);
u8 pmr;
if (ap->port_no) {
switch (pdev->device) {
case 0x0180:
case 0x0181:
pci_read_config_byte(pdev, SIS_PMR, &pmr);
if ((pmr & SIS_PMR_COMBINED) == 0)
addr += SIS180_SATA1_OFS;
break;
case 0x0182:
case 0x0183:
case 0x1182:
case 0x1183:
addr += SIS182_SATA1_OFS;
break;
}
}
return addr;
}
static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
u32 val, val2 = 0;
u8 pmr;
if (sc_reg == SCR_ERROR) /* doesn't exist in PCI cfg space */
return 0xffffffff;
pci_read_config_byte(pdev, SIS_PMR, &pmr);
pci_read_config_dword(pdev, cfg_addr, &val);
if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
(pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
pci_read_config_dword(pdev, cfg_addr+0x10, &val2);
return (val|val2) & 0xfffffffb; /* avoid problems with powerdowned ports */
}
static void sis_scr_cfg_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
u8 pmr;
if (sc_reg == SCR_ERROR) /* doesn't exist in PCI cfg space */
return;
pci_read_config_byte(pdev, SIS_PMR, &pmr);
pci_write_config_dword(pdev, cfg_addr, val);
if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
(pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
pci_write_config_dword(pdev, cfg_addr+0x10, val);
}
static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 val, val2 = 0;
u8 pmr;
if (sc_reg > SCR_CONTROL)
return 0xffffffffU;
if (ap->flags & SIS_FLAG_CFGSCR)
return sis_scr_cfg_read(ap, sc_reg);
pci_read_config_byte(pdev, SIS_PMR, &pmr);
val = inl(ap->ioaddr.scr_addr + (sc_reg * 4));
if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
(pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
val2 = inl(ap->ioaddr.scr_addr + (sc_reg * 4) + 0x10);
return (val | val2) & 0xfffffffb;
}
static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 pmr;
if (sc_reg > SCR_CONTROL)
return;
pci_read_config_byte(pdev, SIS_PMR, &pmr);
if (ap->flags & SIS_FLAG_CFGSCR)
sis_scr_cfg_write(ap, sc_reg, val);
else {
outl(val, ap->ioaddr.scr_addr + (sc_reg * 4));
if ((pdev->device == 0x0182) || (pdev->device == 0x0183) || (pdev->device == 0x1182) ||
(pdev->device == 0x1183) || (pmr & SIS_PMR_COMBINED))
outl(val, ap->ioaddr.scr_addr + (sc_reg * 4)+0x10);
}
}
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
struct ata_probe_ent *probe_ent = NULL;
int rc;
u32 genctl, val;
struct ata_port_info pi = sis_port_info, *ppi[2] = { &pi, &pi };
int pci_dev_busy = 0;
u8 pmr;
u8 port2_start = 0x20;
if (!printed_version++)
dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
rc = pci_enable_device(pdev);
if (rc)
return rc;
rc = pci_request_regions(pdev, DRV_NAME);
if (rc) {
pci_dev_busy = 1;
goto err_out;
}
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
goto err_out_regions;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
goto err_out_regions;
/* check and see if the SCRs are in IO space or PCI cfg space */
pci_read_config_dword(pdev, SIS_GENCTL, &genctl);
if ((genctl & GENCTL_IOMAPPED_SCR) == 0)
pi.flags |= SIS_FLAG_CFGSCR;
/* if hardware thinks SCRs are in IO space, but there are
* no IO resources assigned, change to PCI cfg space.
*/
if ((!(pi.flags & SIS_FLAG_CFGSCR)) &&
((pci_resource_start(pdev, SIS_SCR_PCI_BAR) == 0) ||
(pci_resource_len(pdev, SIS_SCR_PCI_BAR) < 128))) {
genctl &= ~GENCTL_IOMAPPED_SCR;
pci_write_config_dword(pdev, SIS_GENCTL, genctl);
pi.flags |= SIS_FLAG_CFGSCR;
}
pci_read_config_byte(pdev, SIS_PMR, &pmr);
switch (ent->device) {
case 0x0180:
case 0x0181:
/* import the PATA-handling from driver pata_sis */
#ifdef CONFIG_PATA_SIS
switch (pmr & 0x30) {
case 0x10:
ppi[1] = &sis_info133;
break;
case 0x30:
ppi[0] = &sis_info133;
break;
}
#endif
if ((pmr & SIS_PMR_COMBINED) == 0) {
dev_printk(KERN_INFO, &pdev->dev,
"Detected SiS 180/181/964 chipset in SATA mode\n");
port2_start = 64;
} else {
dev_printk(KERN_INFO, &pdev->dev,
"Detected SiS 180/181 chipset in combined mode\n");
port2_start=0;
pi.flags |= ATA_FLAG_SLAVE_POSS;
}
break;
case 0x0182:
case 0x0183:
pci_read_config_dword ( pdev, 0x6C, &val);
if (val & (1L << 31)) {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182/965 chipset\n");
pi.flags |= ATA_FLAG_SLAVE_POSS;
} else {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 182/965L chipset\n");
}
break;
case 0x1182:
case 0x1183:
pci_read_config_dword(pdev, 0x64, &val);
if (val & 0x10000000) {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 1182/1183/966L SATA controller\n");
} else {
dev_printk(KERN_INFO, &pdev->dev, "Detected SiS 1182/1183/966 SATA controller\n");
pi.flags |= ATA_FLAG_SLAVE_POSS;
}
break;
}
probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
if (!probe_ent) {
rc = -ENOMEM;
goto err_out_regions;
}
if (!(probe_ent->port_flags & SIS_FLAG_CFGSCR)) {
probe_ent->port[0].scr_addr =
pci_resource_start(pdev, SIS_SCR_PCI_BAR);
probe_ent->port[1].scr_addr =
pci_resource_start(pdev, SIS_SCR_PCI_BAR) + port2_start;
}
pci_set_master(pdev);
pci_intx(pdev, 1);
/* FIXME: check ata_device_add return value */
ata_device_add(probe_ent);
kfree(probe_ent);
return 0;
err_out_regions:
pci_release_regions(pdev);
err_out:
if (!pci_dev_busy)
pci_disable_device(pdev);
return rc;
}
static int __init sis_init(void)
{
return pci_register_driver(&sis_pci_driver);
}
static void __exit sis_exit(void)
{
pci_unregister_driver(&sis_pci_driver);
}
module_init(sis_init);
module_exit(sis_exit);
