On Wed, 25 Oct 2006 15:06:20 -0400 Jeff Garzik <jeff@xxxxxxxxxx> wrote: > On Wed, Oct 25, 2006 at 11:45:04AM -0700, Stephen Hemminger wrote: > > This laptop has long timeouts during bootup. Something is > > wrong. This is a Sony VAIO NG170. On a positive note suspend works. > > > > Here is the console log during the 40 seconds of dead time. > > What are results from the latest 2.6.19-rcX-gitX, and from the latest -mm? > > Jeff > Same problem with current git tree. [ 1.339696] ata4: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 19 [ 1.339766] scsi2 : ata_piix [ 1.492243] ata3.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32) [ 1.492325] ata3.00: ata3: dev 0 multi count 16 [ 1.495405] ata3.00: configured for UDMA/100 [ 1.495461] scsi3 : ata_piix [ 8.530407] ata4: port is slow to respond, please be patient (Status 0xff) [ 31.505574] ata4: port failed to respond (30 secs, Status 0xff) [ 31.656404] ata4: SRST failed (status 0xFF) [ 31.656459] ata4: SRST failed (err_mask=0x100) [ 31.656514] ata4: softreset failed, retrying in 5 secs [ 36.804622] ata4: SRST failed (status 0xFF) [ 36.804681] ata4: SRST failed (err_mask=0x100) [ 36.804737] ata4: softreset failed, retrying in 5 secs [ 41.951843] ata4: SRST failed (status 0xFF) [ 41.951898] ata4: SRST failed (err_mask=0x100) [ 41.951952] ata4: reset failed, giving up It is Intel ICH7 chips, here are the relevant portions of lspci 0000:00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Sony Corporation: Unknown device 8212 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at <unassigned> Region 1: I/O ports at <unassigned> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at 1810 [size=16] 00: 86 80 df 27 05 00 80 02 02 8a 01 01 00 00 00 00 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 20: 11 18 00 00 00 00 00 00 00 00 00 00 4d 10 12 82 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00 0000:00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controllers cc=IDE (rev 02) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Sony Corporation: Unknown device 8212 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 18b0 [size=8] Region 1: I/O ports at 18a4 [size=4] Region 2: I/O ports at 18a8 [size=8] Region 3: I/O ports at 18a0 [size=4] Region 4: I/O ports at 1890 [size=16] Region 5: Memory at dc444400 (32-bit, non-prefetchable) [size=1K] Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 86 80 c4 27 07 00 b0 02 02 8f 01 01 00 00 00 00 10: b1 18 00 00 a5 18 00 00 a9 18 00 00 a1 18 00 00 20: 91 18 00 00 00 44 44 dc 00 00 00 00 4d 10 12 82 30: 00 00 00 00 70 00 00 00 00 00 00 00 0a 02 00 00 Full log. [ 0.000000] Linux version 2.6.19-rc3 (shemminger@sony-laptop) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #3 SMP PREEMPT Wed Oct 25 13:47:23 PDT 2006 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f690000 (usable) [ 0.000000] BIOS-e820: 000000003f690000 - 000000003f698000 (ACPI data) [ 0.000000] BIOS-e820: 000000003f698000 - 000000003f700000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] 118MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f71b0 [ 0.000000] Entering add_active_range(0, 0, 259728) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 259728 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 259728 [ 0.000000] On node 0 totalpages: 259728 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 237 pages used for memmap [ 0.000000] HighMem zone: 30115 pages, LIFO batch:7 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f70e0 [ 0.000000] ACPI: RSDT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f6916ca [ 0.000000] ACPI: FADT (v002 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697e48 [ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697ecc [ 0.000000] ACPI: MCFG (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697f34 [ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f697f70 [ 0.000000] ACPI: BOOT (v001 SONY J4 0x20060907 PTL 0x00000001) @ 0x3f697fd8 [ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69210b [ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69170a [ 0.000000] ACPI: DSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: 2 duplicate APIC table ignored. [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:14 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:14 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] Detected 1596.091 MHz processor. [ 13.409916] Built 1 zonelists. Total pages: 257699 [ 13.409921] Kernel command line: root=/dev/sda1 ro [ 13.410111] mapped APIC to ffffd000 (fee00000) [ 13.410114] mapped IOAPIC to ffffc000 (fec00000) [ 13.410117] Enabling fast FPU save and restore... done. [ 13.410120] Enabling unmasked SIMD FPU exception support... done. [ 13.410123] Initializing CPU#0 [ 13.410191] CPU 0 irqstacks, hard=c03a4000 soft=c03ac000 [ 13.410195] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 13.411710] Console: colour VGA+ 80x25 [ 13.414446] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 13.414874] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 13.441204] Memory: 1022472k/1038912k available (1567k kernel code, 15808k reserved, 611k data, 204k init, 121408k highmem) [ 13.441294] virtual kernel memory layout: [ 13.441296] fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB) [ 13.441297] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 13.441299] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 13.441300] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 13.441302] .init : 0xc036c000 - 0xc039f000 ( 204 kB) [ 13.441304] .data : 0xc0287d89 - 0xc0320b30 ( 611 kB) [ 13.441305] .text : 0xc0100000 - 0xc0287d89 (1567 kB) [ 13.441738] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 13.501101] Calibrating delay using timer specific routine.. 3194.47 BogoMIPS (lpj=1597238) [ 13.501257] Mount-cache hash table entries: 512 [ 13.501413] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 [ 13.501421] monitor/mwait feature present. [ 13.501475] using mwait in idle threads. [ 13.501531] CPU: L1 I cache: 32K, L1 D cache: 32K [ 13.501617] CPU: L2 cache: 2048K [ 13.501668] CPU: Physical Processor ID: 0 [ 13.501720] CPU: Processor Core ID: 0 [ 13.501773] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000 [ 13.501783] Compat vDSO mapped to ffffe000. [ 13.501846] Checking 'hlt' instruction... OK. [ 13.505201] SMP alternatives: switching to UP code [ 13.505353] ACPI: Core revision 20060707 [ 13.544920] CPU0: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08 [ 13.545109] SMP alternatives: switching to SMP code [ 13.545271] Booting processor 1/1 eip 3000 [ 13.545326] CPU 1 irqstacks, hard=c03a5000 soft=c03ad000 [ 13.555858] Initializing CPU#1 [ 13.615972] Calibrating delay using timer specific routine.. 3191.59 BogoMIPS (lpj=1595795) [ 13.615979] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 [ 13.615985] monitor/mwait feature present. [ 13.615989] CPU: L1 I cache: 32K, L1 D cache: 32K [ 13.615991] CPU: L2 cache: 2048K [ 13.615993] CPU: Physical Processor ID: 0 [ 13.615995] CPU: Processor Core ID: 1 [ 13.615997] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000 [ 13.616464] CPU1: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08 [ 13.617044] Total of 2 processors activated (6386.06 BogoMIPS). [ 13.617298] ENABLING IO-APIC IRQs [ 13.617548] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 13.728856] checking TSC synchronization across 2 CPUs: passed. [ 0.000962] Brought up 2 CPUs [ 0.207488] migration_cost=73 [ 0.207750] checking if image is initramfs... it is [ 0.570873] Freeing initrd memory: 3604k freed [ 0.571302] NET: Registered protocol family 16 [ 0.571451] ACPI: bus type pci registered [ 0.571513] PCI: Using MMCONFIG [ 0.572501] Setting up standard PCI resources [ 0.593906] ACPI: Interpreter enabled [ 0.593961] ACPI: Using IOAPIC for interrupt routing [ 0.606808] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.606869] PCI: Probing PCI hardware (bus 00) [ 0.613788] Boot video device is 0000:00:02.0 [ 0.614281] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO [ 0.614341] PCI quirk: region 1180-11bf claimed by ICH6 GPIO [ 0.614443] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 [ 0.615480] PCI: Transparent bridge - 0000:00:1e.0 [ 0.615597] PCI: Bus #09 (-#0c) is hidden behind transparent bridge #08 (-#09) (try 'pci=assign-busses') [ 0.615676] Please report the result to linux-kernel to fix this permanently [ 0.615788] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.623927] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.624216] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.624503] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 0.625666] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] [ 0.626809] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15) [ 0.627515] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 7 11 12 14 15) [ 0.628207] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.628954] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 [ 0.629694] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. [ 0.630467] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. [ 0.631238] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15) [ 0.631934] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 11 12 14 15) [ 0.636478] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.636541] pnp: PnP ACPI init [ 0.645610] pnp: PnP ACPI: found 9 devices [ 0.645694] intel_rng: FWH not detected [ 0.645889] SCSI subsystem initialized [ 0.645966] PCI: Using ACPI for IRQ routing [ 0.646021] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.646602] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 [ 0.646664] PCI: Bridge: 0000:00:1c.0 [ 0.646719] IO window: 2000-2fff [ 0.646776] MEM window: d6000000-d7ffffff [ 0.646832] PREFETCH window: d0000000-d1ffffff [ 0.646890] PCI: Bridge: 0000:00:1c.1 [ 0.646943] IO window: 3000-3fff [ 0.646999] MEM window: d8000000-d9ffffff [ 0.647056] PREFETCH window: d2000000-d3ffffff [ 0.647114] PCI: Bridge: 0000:00:1c.2 [ 0.647169] IO window: 4000-4fff [ 0.647230] MEM window: da000000-dbffffff [ 0.647292] PREFETCH window: d4000000-d5ffffff [ 0.647356] PCI: Bus 9, cardbus bridge: 0000:08:03.0 [ 0.647412] IO window: 00005000-000050ff [ 0.647469] IO window: 00005400-000054ff [ 0.647526] PREFETCH window: 50000000-51ffffff [ 0.647584] MEM window: 52000000-53ffffff [ 0.647641] PCI: Bridge: 0000:00:1e.0 [ 0.647696] IO window: 5000-5fff [ 0.647751] MEM window: dc000000-dc0fffff [ 0.647807] PREFETCH window: 50000000-51ffffff [ 0.647885] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16 [ 0.647994] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.648015] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17 [ 0.648124] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 0.648144] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 0.648258] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 0.648268] PCI: Enabling device 0000:00:1e.0 (0004 -> 0007) [ 0.648328] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.648343] PCI: Enabling device 0000:08:03.0 (0000 -> 0003) [ 0.648402] ACPI: PCI Interrupt 0000:08:03.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 0.648513] PCI: Setting latency timer of device 0000:08:03.0 to 64 [ 0.648542] NET: Registered protocol family 2 [ 0.658276] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.658476] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 0.659696] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.660356] TCP: Hash tables configured (established 131072 bind 65536) [ 0.660415] TCP reno registered [ 0.660686] Simple Boot Flag at 0x36 set to 0x1 [ 0.661253] highmem bounce pool size: 64 pages [ 0.661456] io scheduler noop registered [ 0.661543] io scheduler anticipatory registered (default) [ 0.661665] io scheduler deadline registered [ 0.661760] io scheduler cfq registered [ 0.662077] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.662127] assign_interrupt_mode Found MSI capability [ 0.662239] Allocate Port Service[0000:00:1c.0:pcie00] [ 0.662276] Allocate Port Service[0000:00:1c.0:pcie02] [ 0.662307] Allocate Port Service[0000:00:1c.0:pcie03] [ 0.662409] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 0.662457] assign_interrupt_mode Found MSI capability [ 0.662550] Allocate Port Service[0000:00:1c.1:pcie00] [ 0.662584] Allocate Port Service[0000:00:1c.1:pcie02] [ 0.662615] Allocate Port Service[0000:00:1c.1:pcie03] [ 0.662710] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 0.662759] assign_interrupt_mode Found MSI capability [ 0.662853] Allocate Port Service[0000:00:1c.2:pcie00] [ 0.662886] Allocate Port Service[0000:00:1c.2:pcie02] [ 0.662922] Allocate Port Service[0000:00:1c.2:pcie03] [ 0.685392] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 0.686530] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 0.686708] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 0.686768] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 0.687072] libata version 2.00 loaded. [ 0.687143] ata_piix 0000:00:1f.1: version 2.00ac6 [ 0.687157] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18 [ 0.687280] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 0.687328] ata1: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1810 irq 14 [ 0.688305] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15 [ 0.688385] scsi0 : ata_piix [ 1.002858] ata1.00: ATAPI, max UDMA/33 [ 1.166641] ata1.00: configured for UDMA/33 [ 1.166705] scsi1 : ata_piix [ 1.166813] ata2: port disabled. ignoring. [ 1.178390] ATA: abnormal status 0xFF on port 0x177 [ 1.187849] scsi 0:0:0:0: CD-ROM PIONEER DVD-RW DVR-K16D 1.00 PQ: 0 ANSI: 5 [ 1.188008] ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ] [ 1.188224] ata_piix 0000:00:1f.2: invalid MAP value 0 [ 1.339464] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 [ 1.339584] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 1.339610] ata3: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 19 [ 1.339696] ata4: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 19 [ 1.339766] scsi2 : ata_piix [ 1.492243] ata3.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32) [ 1.492325] ata3.00: ata3: dev 0 multi count 16 [ 1.495405] ata3.00: configured for UDMA/100 [ 1.495461] scsi3 : ata_piix [ 8.530407] ata4: port is slow to respond, please be patient (Status 0xff) [ 31.505574] ata4: port failed to respond (30 secs, Status 0xff) [ 31.656404] ata4: SRST failed (status 0xFF) [ 31.656459] ata4: SRST failed (err_mask=0x100) [ 31.656514] ata4: softreset failed, retrying in 5 secs [ 36.804622] ata4: SRST failed (status 0xFF) [ 36.804681] ata4: SRST failed (err_mask=0x100) [ 36.804737] ata4: softreset failed, retrying in 5 secs [ 41.951843] ata4: SRST failed (status 0xFF) [ 41.951898] ata4: SRST failed (err_mask=0x100) [ 41.951952] ata4: reset failed, giving up [ 41.952074] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHV2120B 0000 PQ: 0 ANSI: 5 [ 41.952301] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 41.956101] i8042.c: Detected active multiplexing controller, rev 1.1. [ 41.961208] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 41.961269] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 41.961328] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 41.961387] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 41.961446] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 41.961584] mice: PS/2 mouse device common for all mice [ 41.961731] TCP cubic registered [ 41.961789] NET: Registered protocol family 1 [ 41.961857] Using IPI No-Shortcut mode [ 41.961971] ACPI: (supports<6>Time: tsc clocksource has been installed. [ 41.962067] S0 S3 S4 S5) [ 41.962404] Freeing unused kernel memory: 204k freed [ 42.011608] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 42.012264] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 42.012682] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 42.012839] ACPI: Processor [CPU0] (supports 8 throttling states) [ 42.013518] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 42.013874] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 42.014344] ACPI: CPU1 (power states: C1[C1] C2[C2]) [ 42.014496] ACPI: Processor [CPU1] (supports 8 throttling states) [ 42.016427] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707] [ 42.017311] ACPI: Thermal Zone [TZ00] (54 C) [ 42.018667] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707] [ 42.019543] ACPI: Thermal Zone [TZ01] (54 C) [ 42.241000] Time: acpi_pm clocksource has been installed. [ 42.381000] input: AT Translated Set 2 keyboard as /class/input/input0 [ 42.390000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) [ 42.390000] sda: Write Protect is off [ 42.390000] sda: Mode Sense: 00 3a 00 00 [ 42.390000] SCSI device sda: drive cache: write back [ 42.390000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) [ 42.390000] sda: Write Protect is off [ 42.390000] sda: Mode Sense: 00 3a 00 00 [ 42.390000] SCSI device sda: drive cache: write back [ 42.391000] sda: sda1 sda2 sda3 [ 42.732000] sd 2:0:0:0: Attached scsi disk sda [ 43.057000] usbcore: registered new interface driver usbfs [ 43.057000] usbcore: registered new interface driver hub [ 43.058000] usbcore: registered new device driver usb [ 43.060000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20 [ 43.060000] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 43.060000] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 43.060000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 43.060000] ehci_hcd 0000:00:1d.7: debug port 1 [ 43.060000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 43.060000] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xdc444000 [ 43.064000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 43.064000] usb usb1: configuration #1 chosen from 1 choice [ 43.064000] hub 1-0:1.0: USB hub found [ 43.065000] hub 1-0:1.0: 6 ports detected [ 43.065000] USB Universal Host Controller Interface driver v3.0 [ 43.166000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20 [ 43.166000] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 43.166000] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 43.167000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 43.167000] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820 [ 43.167000] usb usb2: configuration #1 chosen from 1 choice [ 43.167000] hub 2-0:1.0: USB hub found [ 43.167000] hub 2-0:1.0: 2 ports detected [ 43.268000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 16 [ 43.268000] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 43.268000] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 43.268000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 43.268000] uhci_hcd 0000:00:1d.1: irq 16, io base 0x00001840 [ 43.268000] usb usb3: configuration #1 chosen from 1 choice [ 43.268000] hub 3-0:1.0: USB hub found [ 43.268000] hub 3-0:1.0: 2 ports detected [ 43.369000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 43.369000] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 43.369000] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 43.369000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 43.369000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860 [ 43.369000] usb usb4: configuration #1 chosen from 1 choice [ 43.369000] hub 4-0:1.0: USB hub found [ 43.369000] hub 4-0:1.0: 2 ports detected [ 43.495000] ide0: I/O resource 0x1F0-0x1F7 not free. [ 43.496000] ide0: ports already in use, skipping probe [ 43.496000] ide1: I/O resource 0x170-0x177 not free. [ 43.496000] ide1: ports already in use, skipping probe [ 43.525000] Attempting manual resume [ 43.570000] kjournald starting. Commit interval 5 seconds [ 43.570000] EXT3-fs: mounted filesystem with ordered data mode. [ 43.575000] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 43.739000] usb 3-1: configuration #1 chosen from 1 choice [ 48.586000] warning: process `ls' used the removed sysctl system call [ 48.888000] scsi 0:0:0:0: Attached scsi generic sg0 type 5 [ 48.888000] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 49.036000] Adding 2104504k swap on /dev/sda2. Priority:-1 extents:1 across:2104504k [ 49.101000] EXT3 FS on sda1, internal journal [ 49.103000] warning: process `touch' used the removed sysctl system call [ 49.166000] warning: process `touch' used the removed sysctl system call [ 49.422000] input: PS/2 Mouse as /class/input/input1 [ 49.441000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input2 [ 49.462000] warning: process `evms_activate' used the removed sysctl system call [ 49.933000] Linux agpgart interface v0.101 (c) Dave Jones [ 49.949000] agpgart: Detected an Intel 945GM Chipset. [ 49.950000] agpgart: Detected 7932K stolen memory. [ 49.965000] Real Time Clock Driver v1.12ac [ 49.968000] agpgart: AGP aperture is 256M @ 0xc0000000 [ 49.990000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 49.993000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 50.025000] input: PC Speaker as /class/input/input3 [ 50.394000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 50.409000] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 50.409000] sky2 v1.10 addr 0xd6000000 irq 17 Yukon-FE (0xb7) rev 1 [ 50.409000] sky2 eth0: addr 00:13:a9:7d:aa:6f [ 50.482000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21 [ 50.482000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 50.536000] hda_codec: Unknown model for ALC262, trying auto-probe from BIOS... [ 50.555000] usbcore: registered new interface driver hiddev [ 50.580000] input: KYE Genius USB Wheel Mouse as /class/input/input4 [ 50.580000] input: USB HID v1.00 Mouse [KYE Genius USB Wheel Mouse] on usb-0000:00:1d.1-1 [ 50.580000] usbcore: registered new interface driver usbhid [ 50.581000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 50.739000] warning: process `alsactl' used the removed sysctl system call [ 50.872000] kjournald starting. Commit interval 5 seconds [ 50.895000] EXT3 FS on sda3, internal journal [ 50.895000] EXT3-fs: mounted filesystem with ordered data mode. [ 52.290000] NET: Registered protocol family 17 [ 55.168000] ACPI: AC Adapter [ADP1] (on-line) [ 55.223000] ACPI: Battery Slot [BAT0] (battery present) [ 55.242000] ACPI: Lid Switch [LID0] [ 55.242000] ACPI: Power Button (CM) [PWRB] [ 55.287000] Using specific hotkey driver [ 55.342000] ibm_acpi: ec object not found [ 55.390000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 55.400000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 58.544000] [drm] Initialized drm 1.0.1 20051102 [ 58.560000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 58.565000] [drm] Initialized i915 1.5.0 20060119 on minor 0 [ 59.117000] sky2 eth0: enabling interface [ 59.221000] sonypi: Sony Programmable I/O Controller Driver v1.26. [ 59.222000] sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on, acpi = on [ 59.222000] sonypi: enabled at irq=11, port1=0x1080, port2=0x1084 [ 59.222000] sonypi: device allocated minor is 63 [ 59.251000] input: Sony Vaio Jogdial as /class/input/input5 [ 59.251000] input: Sony Vaio Keys as /class/input/input6 [ 59.351000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646) [ 59.391000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 657) [ 59.431000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 659) [ 59.472000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646) [ 60.785000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
