This laptop has long timeouts during bootup. Something is wrong. This is a Sony VAIO NG170. On a positive note suspend works. Here is the console log during the 40 seconds of dead time. [ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225 [ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225 [ 2.942000] scsi0 : ata_piix [ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32) [ 3.094000] ata1.00: ata1: dev 0 multi count 16 [ 3.097000] ata1.00: configured for UDMA/100 [ 3.097000] scsi1 : ata_piix [ 10.144000] ata2: port is slow to respond, please be patient [ 33.104000] ata2: port failed to respond (30 secs) [ 33.255000] ata2: SRST failed (status 0xFF) [ 33.255000] ata2: SRST failed (err_mask=0x100) [ 33.255000] ata2: softreset failed, retrying in 5 secs [ 38.407000] ata2: SRST failed (status 0xFF) [ 38.407000] ata2: SRST failed (err_mask=0x100) [ 38.407000] ata2: softreset failed, retrying in 5 secs [ 43.560000] ata2: SRST failed (status 0xFF) [ 43.560000] ata2: SRST failed (err_mask=0x100) [ 43.560000] ata2: reset failed, giving up [ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000 [ 43.561000] Type: Direct-Access ANSI SCSI revision: 05 [ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) Full log: [ 0.000000] Linux version 2.6.18.1 (shemminger@sony-laptop) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Fri Oct 20 15:14:44 PDT 2006 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f690000 (usable) [ 0.000000] BIOS-e820: 000000003f690000 - 000000003f698000 (ACPI data) [ 0.000000] BIOS-e820: 000000003f698000 - 000000003f700000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] Warning only 896MB will be used. [ 0.000000] Use a HIGHMEM enabled kernel. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f71b0 [ 0.000000] On node 0 totalpages: 229376 [ 0.000000] DMA zone: 4096 pages, LIFO batch:0 [ 0.000000] Normal zone: 225280 pages, LIFO batch:31 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f70e0 [ 0.000000] ACPI: RSDT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f6916ca [ 0.000000] ACPI: FADT (v002 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697e48 [ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697ecc [ 0.000000] ACPI: MCFG (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697f34 [ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f697f70 [ 0.000000] ACPI: BOOT (v001 SONY J4 0x20060907 PTL 0x00000001) @ 0x3f697fd8 [ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69210b [ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69170a [ 0.000000] ACPI: DSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x00000000 [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: 2 duplicate APIC table ignored. [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:14 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:14 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] Detected 1596.085 MHz processor. [ 17.971836] Built 1 zonelists. Total pages: 229376 [ 17.971839] Kernel command line: root=/dev/sda1 ro [ 17.972048] mapped APIC to ffffd000 (fee00000) [ 17.972051] mapped IOAPIC to ffffc000 (fec00000) [ 17.972054] Enabling fast FPU save and restore... done. [ 17.972057] Enabling unmasked SIMD FPU exception support... done. [ 17.972061] Initializing CPU#0 [ 17.972126] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 17.973647] Console: colour VGA+ 80x25 [ 17.976113] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 17.976569] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 17.994368] Memory: 902104k/917504k available (1408k kernel code, 14816k reserved, 559k data, 196k init, 0k highmem) [ 17.994449] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 18.054045] Calibrating delay using timer specific routine.. 3194.44 BogoMIPS (lpj=1597223) [ 18.054199] Mount-cache hash table entries: 512 [ 18.054351] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 [ 18.054361] CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 [ 18.054368] monitor/mwait feature present. [ 18.054422] using mwait in idle threads. [ 18.054476] CPU: L1 I cache: 32K, L1 D cache: 32K [ 18.054564] CPU: L2 cache: 2048K [ 18.054616] CPU: Physical Processor ID: 0 [ 18.054668] CPU: Processor Core ID: 0 [ 18.054720] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000 [ 18.054729] Compat vDSO mapped to ffffe000. [ 18.054792] Checking 'hlt' instruction... OK. [ 18.058140] SMP alternatives: switching to UP code [ 18.058293] ACPI: Core revision 20060707 [ 18.091651] CPU0: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08 [ 18.091832] SMP alternatives: switching to SMP code [ 18.092007] Booting processor 1/1 eip 3000 [ 18.102538] Initializing CPU#1 [ 18.162923] Calibrating delay using timer specific routine.. 3191.58 BogoMIPS (lpj=1595793) [ 18.162930] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 [ 18.162938] CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000 [ 18.162943] monitor/mwait feature present. [ 18.162946] CPU: L1 I cache: 32K, L1 D cache: 32K [ 18.162949] CPU: L2 cache: 2048K [ 18.162951] CPU: Physical Processor ID: 0 [ 18.162953] CPU: Processor Core ID: 1 [ 18.162955] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000 [ 18.163353] CPU1: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08 [ 18.163934] Total of 2 processors activated (6386.03 BogoMIPS). [ 18.164188] ENABLING IO-APIC IRQs [ 18.164426] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 18.275811] checking TSC synchronization across 2 CPUs: passed. [ 0.000955] Brought up 2 CPUs [ 0.284715] migration_cost=53 [ 0.284964] checking if image is initramfs... it is [ 0.678499] Freeing initrd memory: 3914k freed [ 0.678916] NET: Registered protocol family 16 [ 0.679050] ACPI: bus type pci registered [ 0.679108] PCI: Using MMCONFIG [ 0.680097] Setting up standard PCI resources [ 0.699770] ACPI: Interpreter enabled [ 0.699825] ACPI: Using IOAPIC for interrupt routing [ 0.712680] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.712738] PCI: Probing PCI hardware (bus 00) [ 0.719670] Boot video device is 0000:00:02.0 [ 0.720318] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 [ 0.721506] PCI: Transparent bridge - 0000:00:1e.0 [ 0.721623] PCI: Bus #09 (-#0c) is hidden behind transparent bridge #08 (-#09) (try 'pci=assign-busses') [ 0.721701] Please report the result to linux-kernel to fix this permanently [ 0.721815] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.729700] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.729986] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.730273] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 0.731404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] [ 0.732533] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15) [ 0.733247] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 7 11 12 14 15) [ 0.733932] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.734674] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 [ 0.735432] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. [ 0.736212] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. [ 0.736976] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15) [ 0.737672] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 11 12 14 15) [ 0.738177] ACPI: Embedded Controller [EC] (gpe 23) interrupt mode. [ 0.743243] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.743312] pnp: PnP ACPI init [ 0.753240] pnp: PnP ACPI: found 9 devices [ 0.753343] PCI: Using ACPI for IRQ routing [ 0.753397] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.753969] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 [ 0.754032] PCI: Bridge: 0000:00:1c.0 [ 0.754087] IO window: 2000-2fff [ 0.754151] MEM window: d6000000-d7ffffff [ 0.754207] PREFETCH window: d0000000-d1ffffff [ 0.754266] PCI: Bridge: 0000:00:1c.1 [ 0.754321] IO window: 3000-3fff [ 0.754376] MEM window: d8000000-d9ffffff [ 0.754433] PREFETCH window: d2000000-d3ffffff [ 0.754491] PCI: Bridge: 0000:00:1c.2 [ 0.754545] IO window: 4000-4fff [ 0.754602] MEM window: da000000-dbffffff [ 0.754658] PREFETCH window: d4000000-d5ffffff [ 0.754725] PCI: Bus 9, cardbus bridge: 0000:08:03.0 [ 0.754781] IO window: 00005000-000050ff [ 0.754839] IO window: 00005400-000054ff [ 0.754896] PREFETCH window: 50000000-51ffffff [ 0.754954] MEM window: 52000000-53ffffff [ 0.755011] PCI: Bridge: 0000:00:1e.0 [ 0.755065] IO window: 5000-5fff [ 0.755131] MEM window: dc000000-dc0fffff [ 0.755187] PREFETCH window: 50000000-51ffffff [ 0.755264] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169 [ 0.755374] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.755396] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177 [ 0.755504] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 0.755524] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185 [ 0.755632] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 0.755642] PCI: Enabling device 0000:00:1e.0 (0004 -> 0007) [ 0.755703] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 0.755718] PCI: Enabling device 0000:08:03.0 (0000 -> 0003) [ 0.755777] ACPI: PCI Interrupt 0000:08:03.0[A] -> GSI 16 (level, low) -> IRQ 177 [ 0.755888] PCI: Setting latency timer of device 0000:08:03.0 to 64 [ 0.755915] NET: Registered protocol family 2 [ 0.769144] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.769338] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 0.770560] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.771234] TCP: Hash tables configured (established 131072 bind 65536) [ 0.771295] TCP reno registered [ 0.771542] Simple Boot Flag at 0x36 set to 0x1 [ 0.772608] Initializing Cryptographic API [ 0.772670] io scheduler noop registered [ 0.772759] io scheduler anticipatory registered (default) [ 0.772885] io scheduler deadline registered [ 0.772985] io scheduler cfq registered [ 0.773309] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 0.773359] assign_interrupt_mode Found MSI capability [ 0.773473] Allocate Port Service[0000:00:1c.0:pcie00] [ 0.773515] Allocate Port Service[0000:00:1c.0:pcie02] [ 0.773550] Allocate Port Service[0000:00:1c.0:pcie03] [ 0.773594] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 0.773643] assign_interrupt_mode Found MSI capability [ 0.773742] Allocate Port Service[0000:00:1c.1:pcie00] [ 0.773783] Allocate Port Service[0000:00:1c.1:pcie02] [ 0.773817] Allocate Port Service[0000:00:1c.1:pcie03] [ 0.773863] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 0.773912] assign_interrupt_mode Found MSI capability [ 0.774011] Allocate Port Service[0000:00:1c.2:pcie00] [ 0.774048] Allocate Port Service[0000:00:1c.2:pcie02] [ 0.774085] Allocate Port Service[0000:00:1c.2:pcie03] [ 0.797628] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 0.798806] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 0.798983] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 0.799042] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 0.799372] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.802193] i8042.c: Detected active multiplexing controller, rev 1.1. [ 0.805641] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 0.806389] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 0.807395] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 0.809028] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 0.809985] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.810103] mice: PS/2 mouse device common for all mice [ 0.810253] TCP bic registered [ 0.810943] NET: Registered protocol family 1 [ 0.811008] Using IPI No-Shortcut mode [ 0.811377] Time: tsc clocksource has been installed. [ 0.811473] ACPI: (supports S0 S3 S4 S5) [ 0.811856] Freeing unused kernel memory: 196k freed [ 0.862634] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 0.863294] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 0.864590] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 0.864744] ACPI: Processor [CPU0] (supports 8 throttling states) [ 0.865429] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 0.865786] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707] [ 0.866254] ACPI: CPU1 (power states: C1[C1] C2[C2]) [ 0.866408] ACPI: Processor [CPU1] (supports 8 throttling states) [ 0.868132] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707] [ 0.869086] ACPI: Thermal Zone [TZ00] (36 C) [ 0.870127] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707] [ 0.871051] ACPI: Thermal Zone [TZ01] (36 C) [ 1.051000] Time: acpi_pm clocksource has been installed. [ 1.409000] ICH7: IDE controller at PCI slot 0000:00:1f.1 [ 1.409000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185 [ 1.409000] ICH7: chipset revision 2 [ 1.409000] ICH7: not 100% native mode: will probe irqs later [ 1.409000] ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio [ 1.410000] Probing IDE interface ide0... [ 1.600000] input: AT Translated Set 2 keyboard as /class/input/input0 [ 2.082000] hda: PIONEER DVD-RW DVR-K16D, ATAPI CD/DVD-ROM drive [ 2.695000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 2.703000] hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33) [ 2.704000] Uniform CD-ROM driver Revision: 3.20 [ 2.785000] SCSI subsystem initialized [ 2.789000] libata version 2.00 loaded. [ 2.791000] ata_piix 0000:00:1f.2: version 2.00 [ 2.791000] ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ] [ 2.791000] ata_piix 0000:00:1f.2: invalid MAP value 0 [ 2.942000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 225 [ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225 [ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225 [ 2.942000] scsi0 : ata_piix [ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32) [ 3.094000] ata1.00: ata1: dev 0 multi count 16 [ 3.097000] ata1.00: configured for UDMA/100 [ 3.097000] scsi1 : ata_piix [ 10.144000] ata2: port is slow to respond, please be patient [ 33.104000] ata2: port failed to respond (30 secs) [ 33.255000] ata2: SRST failed (status 0xFF) [ 33.255000] ata2: SRST failed (err_mask=0x100) [ 33.255000] ata2: softreset failed, retrying in 5 secs [ 38.407000] ata2: SRST failed (status 0xFF) [ 38.407000] ata2: SRST failed (err_mask=0x100) [ 38.407000] ata2: softreset failed, retrying in 5 secs [ 43.560000] ata2: SRST failed (status 0xFF) [ 43.560000] ata2: SRST failed (err_mask=0x100) [ 43.560000] ata2: reset failed, giving up [ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000 [ 43.561000] Type: Direct-Access ANSI SCSI revision: 05 [ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) [ 43.567000] sda: Write Protect is off [ 43.567000] sda: Mode Sense: 00 3a 00 00 [ 43.567000] SCSI device sda: drive cache: write back [ 43.568000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) [ 43.568000] sda: Write Protect is off [ 43.568000] sda: Mode Sense: 00 3a 00 00 [ 43.568000] SCSI device sda: drive cache: write back [ 43.568000] sda: sda1 sda2 sda3 [ 43.924000] sd 0:0:0:0: Attached scsi disk sda [ 44.182000] usbcore: registered new driver usbfs [ 44.182000] usbcore: registered new driver hub [ 44.188000] USB Universal Host Controller Interface driver v3.0 [ 44.188000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 233 [ 44.188000] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 44.188000] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 44.188000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 44.188000] uhci_hcd 0000:00:1d.0: irq 233, io base 0x00001820 [ 44.189000] usb usb1: configuration #1 chosen from 1 choice [ 44.189000] hub 1-0:1.0: USB hub found [ 44.189000] hub 1-0:1.0: 2 ports detected [ 44.200000] ieee1394: Initialized config rom entry `ip1394' [ 44.290000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 169 [ 44.291000] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 44.291000] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 44.291000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 44.291000] uhci_hcd 0000:00:1d.1: irq 169, io base 0x00001840 [ 44.291000] usb usb2: configuration #1 chosen from 1 choice [ 44.291000] hub 2-0:1.0: USB hub found [ 44.291000] hub 2-0:1.0: 2 ports detected [ 44.392000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 233 [ 44.393000] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 44.393000] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 44.393000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3 [ 44.393000] ehci_hcd 0000:00:1d.7: debug port 1 [ 44.393000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 44.393000] ehci_hcd 0000:00:1d.7: irq 233, io mem 0xdc444000 [ 44.397000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 44.397000] usb usb3: configuration #1 chosen from 1 choice [ 44.397000] hub 3-0:1.0: USB hub found [ 44.397000] hub 3-0:1.0: 6 ports detected [ 44.499000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185 [ 44.499000] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 44.499000] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 44.499000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 44.499000] uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860 [ 44.499000] usb usb4: configuration #1 chosen from 1 choice [ 44.499000] hub 4-0:1.0: USB hub found [ 44.499000] hub 4-0:1.0: 2 ports detected [ 44.601000] PCI: Enabling device 0000:08:03.1 (0000 -> 0002) [ 44.601000] ACPI: PCI Interrupt 0000:08:03.1[A] -> GSI 16 (level, low) -> IRQ 177 [ 44.601000] PCI: Setting latency timer of device 0000:08:03.1 to 64 [ 44.658000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[dc005000-dc0057ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 44.670000] Probing IDE interface ide1... [ 45.211000] Attempting manual resume [ 45.223000] EXT3-fs: INFO: recovery required on readonly filesystem. [ 45.223000] EXT3-fs: write access will be enabled during recovery. [ 45.250000] kjournald starting. Commit interval 5 seconds [ 45.250000] EXT3-fs: recovery complete. [ 45.251000] EXT3-fs: mounted filesystem with ordered data mode. [ 45.916000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460302320543] [ 50.698000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 51.622000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 51.705000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 51.724000] Linux agpgart interface v0.101 (c) Dave Jones [ 51.734000] agpgart: Detected an Intel 945GM Chipset. [ 51.735000] agpgart: Detected 7932K stolen memory. [ 51.753000] agpgart: AGP aperture is 256M @ 0xc0000000 [ 51.824000] input: PC Speaker as /class/input/input1 [ 51.931000] Real Time Clock Driver v1.12ac [ 52.325000] input: PS/2 Mouse as /class/input/input2 [ 52.345000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input3 [ 52.387000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 177 [ 52.387000] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 52.387000] sky2 v1.5 addr 0xd6000000 irq 177 Yukon-FE (0xb7) rev 1 [ 52.388000] sky2 eth0: addr 00:13:a9:7d:aa:6f [ 52.442000] ts: Compaq touchscreen protocol output [ 52.649000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58 [ 52.649000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 52.699000] sky2 eth0: enabling interface [ 52.741000] hda_codec: Unknown model for ALC262, trying auto-probe from BIOS... [ 52.967000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 52.967000] ieee1394: sbp2: Try serialize_io=0 for better performance [ 53.023000] Adding 2104504k swap on /dev/sda2. Priority:-1 extents:1 across:2104504k [ 53.067000] EXT3 FS on sda1, internal journal [ 53.677000] kjournald starting. Commit interval 5 seconds [ 53.678000] EXT3 FS on sda3, internal journal [ 53.679000] EXT3-fs: mounted filesystem with ordered data mode. [ 53.809000] NET: Registered protocol family 17 [ 54.587000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control none [ 57.064000] NET: Registered protocol family 10 [ 57.064000] lo: Disabled Privacy Extensions [ 57.064000] IPv6 over IPv4 tunneling driver [ 58.956000] ACPI: AC Adapter [ADP1] (on-line) [ 59.006000] ACPI: Battery Slot [BAT0] (battery present) [ 59.021000] ACPI: Lid Switch [LID0] [ 59.022000] ACPI: Power Button (CM) [PWRB] [ 59.067000] Using specific hotkey driver [ 59.138000] ibm_acpi: ec object not found [ 59.176000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi' [ 59.186000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 62.645000] [drm] Initialized drm 1.0.1 20051102 [ 62.660000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177 [ 62.662000] [drm] Initialized i915 1.5.0 20060119 on minor 0 [ 63.033000] sonypi: Sony Programmable I/O Controller Driver v1.26. [ 63.036000] sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on, acpi = on [ 63.036000] sonypi: enabled at irq=11, port1=0x1080, port2=0x1084 [ 63.036000] sonypi: device allocated minor is 63 [ 63.037000] input: Sony Vaio Jogdial as /class/input/input4 [ 63.047000] input: Sony Vaio Keys as /class/input/input5 [ 63.176000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646) [ 63.218000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 657) [ 63.260000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 659) [ 63.307000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646) [ 67.132000] psmouse.c: GlidePoint at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away. [ 67.256000] eth0: no IPv6 routers present [ 67.640000] psmouse.c: resync failed, issuing reconnect request - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
