It works if i simply ignore the failed ata_dev_set_xfermode call. Regards, Thomas -------- Original-Nachricht -------- Datum: Mon, 28 Aug 2006 13:38:07 +0200 Von: "Thomas Pfaff" <tpfaff@xxxxxxx> An: linux-ide@xxxxxxxxxxxxxxx Betreff: CompactFlash on VT6421 PATA (failed to set xfermode) > I have some trouble with a Hitachi XX.V.3.7 CompactFlash connected to an > VIA VT6421 Raid Controller together with kernel 2.6.17. > > First i had to add a patch from VIA to support PATA in sata-via.c. > > Now i get following error during boot : > > libata version 1.20 loaded. > sata_via 0000:00:14.0: version 1.1 > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 > PCI: setting IRQ 5 as level-triggered > ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 5 (level, low) > -> IRQ 5 > sata_via 0000:00:14.0: routed to hard irq line 7 > ata_device_add: ENTER > ata_host_add: ENTER > ata_port_start: prd alloc, virt cf63e000, dma f63e000 > ata1: PATA max UDMA/133 cmd 0xFD00 ctl 0xFD0A bmdma 0xF900 irq 5 > ata_host_add: ENTER > ata_port_start: prd alloc, virt cf626000, dma f626000 > ata2: PATA max UDMA/133 cmd 0xFC00 ctl 0xFC0A bmdma 0xF908 irq 5 > ata_host_add: ENTER > ata_port_start: prd alloc, virt c12e9000, dma 12e9000 > ata3: PATA max UDMA/133 cmd 0xFB00 ctl 0xFB0A bmdma 0xF910 irq 5 > ata_device_add: probe begin > ata_device_add: ata1: bus probe begin > ata_bus_reset: ENTER, host 1, port 0 > ata_bus_softreset: ata1: bus reset via SRST > ata1: disabling port > ata_bus_reset: EXIT > ata_device_add: ata1: bus probe end > scsi0 : sata_via > ata_device_add: ata2: bus probe begin > ata_bus_reset: ENTER, host 2, port 1 > ata_bus_softreset: ata2: bus reset via SRST > ata2: disabling port > ata_bus_reset: EXIT > ata_device_add: ata2: bus probe end > scsi1 : sata_via > ata_device_add: ata3: bus probe begin > ata_bus_reset: ENTER, host 3, port 2 > ata_bus_softreset: ata3: bus reset via SRST > ata_dev_classify: found ATA device by sig > ata_bus_reset: EXIT > ata_dev_read_id: ENTER, host 3, dev 1 > ata_dev_select: ENTER, ata3: device 1, wait 1 > ata_dev_select: ENTER, ata3: device 1, wait 1 > ata_exec_command_pio: ata3: cmd 0xEC > ata_pio_sector: data read > ata_dev_init_params: init dev params > ata_dev_select: ENTER, ata3: device 1, wait 1 > ata_tf_load_pio: feat 0x0 nsect 0x30 lba 0x0 0x0 0x0 > ata_tf_load_pio: device 0xBE > ata_exec_command_pio: ata3: cmd 0x91 > ata_host_intr: ata3: protocol 1 (dev_stat 0x50) > ata_dev_init_params: EXIT, err_mask=0 > ata_dev_select: ENTER, ata3: device 1, wait 1 > ata_exec_command_pio: ata3: cmd 0xEC > ata_pio_sector: data read > ata_dev_configure: ENTER, host 3, dev 1 > ata3: dev 1 cfg 49:0200 82:7000 83:4004 84:4000 85:7000 86:0004 87:4000 > 88:0000 > ata_dump_id: 49==0x0200 53==0x0003 63==0x0000 64==0x0003 75==0x0000 > ata_dump_id: 80==0x0000 81==0x0000 82==0x7000 83==0x4004 84==0x4000 > ata_dump_id: 88==0x0000 93==0x0000 > ata3: dev 1 ATA-0, max PIO4, 500400 sectors: LBA > ata_dev_configure: EXIT, drv_stat = 0x50 > ata_dev_set_xfermode: set features - xfer mode > ata_dev_select: ENTER, ata3: device 1, wait 1 > ata_tf_load_pio: feat 0x3 nsect 0xC lba 0x0 0x0 0x0 > ata_tf_load_pio: device 0xB0 > ata_exec_command_pio: ata3: cmd 0xEF > ata_host_intr: ata3: protocol 1 (dev_stat 0x51) > ata_dev_set_xfermode: EXIT, err_mask=1 > ata3: failed to set xfermode (err_mask=0x1) > ata_device_add: ata3: bus probe end > scsi2 : sata_via > ata_device_add: host probe begin > ata_device_add: EXIT, returning 3 > > What does "failed to set xfermode (err_mask=0x1)" means ? > > Is this a problem with the CompactFlash card or with the PATA support in > sata-via ? > > Thank you in advance, > Thomas -- Der GMX SmartSurfer hilft bis zu 70% Ihrer Onlinekosten zu sparen! Ideal für Modem und ISDN: http://www.gmx.net/de/go/smartsurfer - To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
