Ar Iau, 2006-08-24 am 18:09 +0100, ysgrifennodd Alan Cox:
>
> --- a/drivers/ata/ata_piix.c
Please ignore that diff I'm an idiot and if you don't have git-diff
aliased wrongly then git-diff -R works rather well 8)
Use this instead
Signed-off-by: Alan Cox <alan@xxxxxxxxxx>
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 22b2dba..62b1a3f 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -93,7 +93,7 @@
#include <linux/libata.h>
#define DRV_NAME "ata_piix"
-#define DRV_VERSION "2.00"
+#define DRV_VERSION "2.00-u1ac40"
enum {
PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
@@ -473,6 +473,24 @@ module_param(force_pcs, int, 0444);
MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around "
"device mis-detection (0=default, 1=ignore PCS, 2=honor PCS)");
+
+struct ich_laptop {
+ u16 device;
+ u16 subvendor;
+ u16 subdevice;
+};
+
+/*
+ * List of laptops that use short cables rather than 80 wire
+ */
+
+static const struct ich_laptop ich_laptop[] = {
+ /* devid, subvendor, subdev */
+ { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
+ /* end marker */
+ { 0, }
+};
+
/**
* piix_pata_cbl_detect - Probe host controller cable detect info
* @ap: Port for which cable detect info is desired
@@ -486,12 +504,21 @@ MODULE_PARM_DESC(force_pcs, "force honor
static void piix_pata_cbl_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ const struct ich_laptop *lap = &ich_laptop[0];
u8 tmp, mask;
/* no 80c support in host controller? */
if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0)
goto cbl40;
+ /* Check for specials - Acer Aspire 5602WLMi */
+ while (lap->device) {
+ if (lap->device == pdev->device &&
+ lap->subvendor == pdev->subsystem_vendor &&
+ lap->subdevice == pdev->subsystem_device)
+ return ATA_CBL_PATA40_SHORT;
+ lap++;
+ }
/* check BIOS cable detect results */
mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
@@ -577,6 +604,7 @@ static unsigned int piix_sata_present_ma
return present_mask;
}
+
/**
* piix_sata_softreset - reset SATA host port via ATA SRST
* @ap: port to reset
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 1c93154..82dc3ad 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3093,6 +3093,13 @@ static void ata_dev_xfermask(struct ata_
*/
if (ap->cbl == ATA_CBL_PATA40)
xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
+ /* Apply drive side cable rule. Unknown or 80 pin cables reported
+ * host side are checked drive side as well. Cases where we know a
+ * 40wire cable is used safely for 80 are not checked here.
+ */
+ if (ata_drive_40wire(dev->id) && (ap->cbl == ATA_CBL_PATA_UNK || ap->cbl == ATA_CBL_PATA80))
+ xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
+
xfer_mask &= ata_pack_xfermask(dev->pio_mask,
dev->mwdma_mask, dev->udma_mask);
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 991b858..0a7a284 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -200,8 +200,9 @@ enum {
ATA_CBL_NONE = 0,
ATA_CBL_PATA40 = 1,
ATA_CBL_PATA80 = 2,
- ATA_CBL_PATA_UNK = 3,
- ATA_CBL_SATA = 4,
+ ATA_CBL_PATA40_SHORT = 3, /* 40 wire cable to high UDMA spec */
+ ATA_CBL_PATA_UNK = 4,
+ ATA_CBL_SATA = 5,
/* SATA Status and Control Registers */
SCR_STATUS = 0,
@@ -342,6 +343,15 @@ static inline int ata_id_is_cfa(const u1
return 0;
}
+static inline int ata_drive_40wire(const u16 *dev_id)
+{
+ if (ata_id_major_version(dev_id) >= 5 && ata_id_is_sata(dev_id))
+ return 0; /* SATA */
+ if (dev_id[93] & 0x4000)
+ return 0; /* 80 wire */
+ return 1;
+}
+
static inline int atapi_cdb_len(const u16 *dev_id)
{
u16 tmp = dev_id[0] & 0x3;
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
