On Thu, Sep 17, 2020 at 06:27:28PM +0300, Dmitry Osipenko wrote:
> 17.09.2020 14:25, Thierry Reding пишет:
> > On Wed, Sep 09, 2020 at 01:39:38AM +0300, Dmitry Osipenko wrote:
> >> The "non_hs_mode" divisor value is fixed, thus there is no need to have
> >> the variable i2c_dev.clk_divisor_non_hs_mode struct member. Let's remove
> >> it and move the mode selection into tegra_i2c_init() where it can be
> >> united with the timing selection.
> >>
> >> Reviewed-by: Michał Mirosław <mirq-linux@xxxxxxxxxxxx>
> >> Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
> >> ---
> >> drivers/i2c/busses/i2c-tegra.c | 46 ++++++++++++++++------------------
> >> 1 file changed, 21 insertions(+), 25 deletions(-)
> >>
> >> diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
> >> index 720a75439e91..85ed0e02d48c 100644
> >> --- a/drivers/i2c/busses/i2c-tegra.c
> >> +++ b/drivers/i2c/busses/i2c-tegra.c
> >> @@ -250,7 +250,6 @@ struct tegra_i2c_hw_feature {
> >> * @msg_buf_remaining: size of unsent data in the message buffer
> >> * @msg_read: identifies read transfers
> >> * @bus_clk_rate: current I2C bus clock rate
> >> - * @clk_divisor_non_hs_mode: clock divider for non-high-speed modes
> >> * @is_multimaster_mode: track if I2C controller is in multi-master mode
> >> * @tx_dma_chan: DMA transmit channel
> >> * @rx_dma_chan: DMA receive channel
> >> @@ -281,7 +280,6 @@ struct tegra_i2c_dev {
> >> size_t msg_buf_remaining;
> >> int msg_read;
> >> u32 bus_clk_rate;
> >> - u16 clk_divisor_non_hs_mode;
> >> bool is_multimaster_mode;
> >> struct dma_chan *tx_dma_chan;
> >> struct dma_chan *rx_dma_chan;
> >> @@ -783,6 +781,7 @@ static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev)
> >> u32 val;
> >> int err;
> >> u32 clk_divisor, clk_multiplier;
> >> + u32 non_hs_mode;
> >> u32 tsu_thd;
> >> u8 tlow, thigh;
> >>
> >> @@ -805,24 +804,33 @@ static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev)
> >> if (i2c_dev->is_vi)
> >> tegra_i2c_vi_init(i2c_dev);
> >>
> >> - /* Make sure clock divisor programmed correctly */
> >> - clk_divisor = FIELD_PREP(I2C_CLK_DIVISOR_HSMODE,
> >> - i2c_dev->hw->clk_divisor_hs_mode) |
> >> - FIELD_PREP(I2C_CLK_DIVISOR_STD_FAST_MODE,
> >> - i2c_dev->clk_divisor_non_hs_mode);
> >> - i2c_writel(i2c_dev, clk_divisor, I2C_CLK_DIVISOR);
> >> -
> >> - if (i2c_dev->bus_clk_rate > I2C_MAX_STANDARD_MODE_FREQ &&
> >> - i2c_dev->bus_clk_rate <= I2C_MAX_FAST_MODE_PLUS_FREQ) {
> >> + switch (i2c_dev->bus_clk_rate) {
> >> + case I2C_MAX_STANDARD_MODE_FREQ + 1 ... I2C_MAX_FAST_MODE_PLUS_FREQ:
> >
> > Is there are particular reason for switching the simple conditional to a
> > switch here? The old variant looks much easier to understand to me.
>
> The reason is make it readable :) For me it's too difficult to read > <=
> && { } + no proper indentation.
Guess this is very subjective then... It would've been nice to avoid the
+ 1 and instead use the correct enumeration value. I think that would've
made it a little bit easier on the eye.
But anyway, no reason to hold up this patch set:
Reviewed-by: Thierry Reding <treding@xxxxxxxxxx>
Attachment:
signature.asc
Description: PGP signature
