The pca9539-driver in drivers/i2c/chips which just exports its registers to sysfs is superseeded by drivers/gpio/pca953x.c which properly uses the gpiolib. As this driver has been deprecated for more than a year, finally remove it. Signed-off-by: Wolfram Sang <w.sang@xxxxxxxxxxxxxx> Cc: Ben Gardner <gardner.ben@xxxxxxxxx> Cc: Jean Delvare <khali@xxxxxxxxxxxx> --- Documentation/i2c/chips/pca9539 | 58 --------------- drivers/i2c/chips/Kconfig | 13 ---- drivers/i2c/chips/Makefile | 1 - drivers/i2c/chips/pca9539.c | 152 --------------------------------------- 4 files changed, 0 insertions(+), 224 deletions(-) delete mode 100644 Documentation/i2c/chips/pca9539 delete mode 100644 drivers/i2c/chips/pca9539.c diff --git a/Documentation/i2c/chips/pca9539 b/Documentation/i2c/chips/pca9539 deleted file mode 100644 index 6aff890..0000000 --- a/Documentation/i2c/chips/pca9539 +++ /dev/null @@ -1,58 +0,0 @@ -Kernel driver pca9539 -===================== - -NOTE: this driver is deprecated and will be dropped soon, use -drivers/gpio/pca9539.c instead. - -Supported chips: - * Philips PCA9539 - Prefix: 'pca9539' - Addresses scanned: none - Datasheet: - http://www.semiconductors.philips.com/acrobat/datasheets/PCA9539_2.pdf - -Author: Ben Gardner <bgardner@xxxxxxxxxx> - - -Description ------------ - -The Philips PCA9539 is a 16 bit low power I/O device. -All 16 lines can be individually configured as an input or output. -The input sense can also be inverted. -The 16 lines are split between two bytes. - - -Detection ---------- - -The PCA9539 is difficult to detect and not commonly found in PC machines, -so you have to pass the I2C bus and address of the installed PCA9539 -devices explicitly to the driver at load time via the force=... parameter. - - -Sysfs entries -------------- - -Each is a byte that maps to the 8 I/O bits. -A '0' suffix is for bits 0-7, while '1' is for bits 8-15. - -input[01] - read the current value -output[01] - sets the output value -direction[01] - direction of each bit: 1=input, 0=output -invert[01] - toggle the input bit sense - -input reads the actual state of the line and is always available. -The direction defaults to input for all channels. - - -General Remarks ---------------- - -Note that each output, direction, and invert entry controls 8 lines. -You should use the read, modify, write sequence. -For example. to set output bit 0 of 1. - val=$(cat output0) - val=$(( $val | 1 )) - echo $val > output0 - diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig index 1b5455e..8cd1a7f 100644 --- a/drivers/i2c/chips/Kconfig +++ b/drivers/i2c/chips/Kconfig @@ -33,19 +33,6 @@ config SENSORS_PCF8574 These devices are hard to detect and rarely found on mainstream hardware. If unsure, say N. -config SENSORS_PCA9539 - tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)" - depends on EXPERIMENTAL && GPIO_PCA953X = "n" - help - If you say yes here you get support for the Philips PCA9539 - 16-bit I/O port. - - This driver can also be built as a module. If so, the module - will be called pca9539. - - This driver is deprecated and will be dropped soon. Use - drivers/gpio/pca953x.c instead. - config SENSORS_TSL2550 tristate "Taos TSL2550 ambient light sensor" depends on EXPERIMENTAL diff --git a/drivers/i2c/chips/Makefile b/drivers/i2c/chips/Makefile index fceb377..8cd778d 100644 --- a/drivers/i2c/chips/Makefile +++ b/drivers/i2c/chips/Makefile @@ -11,7 +11,6 @@ # obj-$(CONFIG_DS1682) += ds1682.o -obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o diff --git a/drivers/i2c/chips/pca9539.c b/drivers/i2c/chips/pca9539.c deleted file mode 100644 index 270de4e..0000000 --- a/drivers/i2c/chips/pca9539.c +++ /dev/null @@ -1,152 +0,0 @@ -/* - pca9539.c - 16-bit I/O port with interrupt and reset - - Copyright (C) 2005 Ben Gardner <bgardner@xxxxxxxxxx> - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; version 2 of the License. -*/ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/slab.h> -#include <linux/i2c.h> -#include <linux/hwmon-sysfs.h> - -/* Addresses to scan: none, device is not autodetected */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(pca9539); - -enum pca9539_cmd -{ - PCA9539_INPUT_0 = 0, - PCA9539_INPUT_1 = 1, - PCA9539_OUTPUT_0 = 2, - PCA9539_OUTPUT_1 = 3, - PCA9539_INVERT_0 = 4, - PCA9539_INVERT_1 = 5, - PCA9539_DIRECTION_0 = 6, - PCA9539_DIRECTION_1 = 7, -}; - -/* following are the sysfs callback functions */ -static ssize_t pca9539_show(struct device *dev, struct device_attribute *attr, - char *buf) -{ - struct sensor_device_attribute *psa = to_sensor_dev_attr(attr); - struct i2c_client *client = to_i2c_client(dev); - return sprintf(buf, "%d\n", i2c_smbus_read_byte_data(client, - psa->index)); -} - -static ssize_t pca9539_store(struct device *dev, struct device_attribute *attr, - const char *buf, size_t count) -{ - struct sensor_device_attribute *psa = to_sensor_dev_attr(attr); - struct i2c_client *client = to_i2c_client(dev); - unsigned long val = simple_strtoul(buf, NULL, 0); - if (val > 0xff) - return -EINVAL; - i2c_smbus_write_byte_data(client, psa->index, val); - return count; -} - -/* Define the device attributes */ - -#define PCA9539_ENTRY_RO(name, cmd_idx) \ - static SENSOR_DEVICE_ATTR(name, S_IRUGO, pca9539_show, NULL, cmd_idx) - -#define PCA9539_ENTRY_RW(name, cmd_idx) \ - static SENSOR_DEVICE_ATTR(name, S_IRUGO | S_IWUSR, pca9539_show, \ - pca9539_store, cmd_idx) - -PCA9539_ENTRY_RO(input0, PCA9539_INPUT_0); -PCA9539_ENTRY_RO(input1, PCA9539_INPUT_1); -PCA9539_ENTRY_RW(output0, PCA9539_OUTPUT_0); -PCA9539_ENTRY_RW(output1, PCA9539_OUTPUT_1); -PCA9539_ENTRY_RW(invert0, PCA9539_INVERT_0); -PCA9539_ENTRY_RW(invert1, PCA9539_INVERT_1); -PCA9539_ENTRY_RW(direction0, PCA9539_DIRECTION_0); -PCA9539_ENTRY_RW(direction1, PCA9539_DIRECTION_1); - -static struct attribute *pca9539_attributes[] = { - &sensor_dev_attr_input0.dev_attr.attr, - &sensor_dev_attr_input1.dev_attr.attr, - &sensor_dev_attr_output0.dev_attr.attr, - &sensor_dev_attr_output1.dev_attr.attr, - &sensor_dev_attr_invert0.dev_attr.attr, - &sensor_dev_attr_invert1.dev_attr.attr, - &sensor_dev_attr_direction0.dev_attr.attr, - &sensor_dev_attr_direction1.dev_attr.attr, - NULL -}; - -static struct attribute_group pca9539_defattr_group = { - .attrs = pca9539_attributes, -}; - -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int pca9539_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return -ENODEV; - - strlcpy(info->type, "pca9539", I2C_NAME_SIZE); - - return 0; -} - -static int pca9539_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - /* Register sysfs hooks */ - return sysfs_create_group(&client->dev.kobj, - &pca9539_defattr_group); -} - -static int pca9539_remove(struct i2c_client *client) -{ - sysfs_remove_group(&client->dev.kobj, &pca9539_defattr_group); - return 0; -} - -static const struct i2c_device_id pca9539_id[] = { - { "pca9539", 0 }, - { } -}; - -static struct i2c_driver pca9539_driver = { - .driver = { - .name = "pca9539", - }, - .probe = pca9539_probe, - .remove = pca9539_remove, - .id_table = pca9539_id, - - .detect = pca9539_detect, - .address_data = &addr_data, -}; - -static int __init pca9539_init(void) -{ - return i2c_add_driver(&pca9539_driver); -} - -static void __exit pca9539_exit(void) -{ - i2c_del_driver(&pca9539_driver); -} - -MODULE_AUTHOR("Ben Gardner <bgardner@xxxxxxxxxx>"); -MODULE_DESCRIPTION("PCA9539 driver"); -MODULE_LICENSE("GPL"); - -module_init(pca9539_init); -module_exit(pca9539_exit); - -- 1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-i2c" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
