Hi, checked it again. Your lnbp21 patch definitely kills S2 tuning on the Terratec Cinergy S2 PCI HD. mfg Edgar ( gimli ) Hucek >> Hi, >> >> with your patch i run into following problem on a Terratec Cinergy S2 >> PCI >> HD : >> >> [ 143.818103] stb6100_set_frequency: Frequency=1588000 >> [ 143.826681] stb6100_get_frequency: Frequency=1587990 >> [ 143.840867] stb6100_get_bandwidth: Bandwidth=10000000 >> [ 150.568018] mantis_ack_wait (0): Slave RACK Fail ! >> [ 150.568372] stb6100_set_bandwidth: Invalid parameter >> [ 156.596525] mantis_ack_wait (0): Slave RACK Fail ! >> [ 156.596880] stb6100_get_bandwidth: Invalid parameter >> [ 162.784014] mantis_ack_wait (0): Slave RACK Fail ! >> [ 162.784368] stb6100_get_bandwidth: Invalid parameter >> [ 168.848014] mantis_ack_wait (0): Slave RACK Fail ! >> [ 168.848368] stb6100_set_frequency: Invalid parameter >> [ 174.896016] mantis_ack_wait (0): Slave RACK Fail ! >> [ 174.896371] stb6100_get_frequency: Invalid parameter >> >> cu >> >> Edgar (gimli) Hucek > > Hi Edgar, > > I don't believe the Slave RACK problem is caused by my LNBP21 patch -- I > saw it before > and I posted a fix for it already at > http://linuxtv.org/pipermail/linux-dvb/2008-December/030829.html > > Here it is again: > > diff -r 28324bc3d694 linux/drivers/media/dvb/mantis/mantis_i2c.c > --- a/linux/drivers/media/dvb/mantis/mantis_i2c.c > +++ b/linux/drivers/media/dvb/mantis/mantis_i2c.c > @@ -42,7 +42,7 @@ static int mantis_ack_wait(struct mantis > dprintk(verbose, MANTIS_DEBUG, 1, "Master !I2CDONE"); > rc = -EREMOTEIO; > } > - while (!(mantis->mantis_int_stat & MANTIS_INT_I2CRACK)) { > + while (!(mantis->mantis_int_stat & MANTIS_INT_I2CDONE)) { > dprintk(verbose, MANTIS_DEBUG, 1, "Waiting for Slave > RACK"); > mantis->mantis_int_stat = mmread(MANTIS_INT_STAT); > msleep(5); > > > Regards, > Hans > > >> >> With the Azurewave AD-SP400 (Twinhan VP-1041 / Technisat HD2 / >> >> ?poss. Terratec Cinergy S2 PCI HD) >> >> there seems to be a driver bug when tuning some channels immediately >> >> after boot or after resuming from sleep (which is entered after 1 >> minute >> >> idle). >> >> So the initialisation seems to be unsuitable for tuning some >> channels. >> >> >> >> But... if another channel is tuned successfully first then the bad >> >> channels *CAN* be tuned >> >> (if you are quick and do it before it sleeps again). >> >> >> >> It looks like the problem channels are all horizontal but perhaps >> other >> >> parameters are >> >> relevant too/instead. >> >> >> >> Can anyone help? >> >> Instructions for reproducing the problem on Astra 19.2E or Hotbird >> 13.0E >> >> are below. >> >> >> >> I don't know whether the problem is in the mantis, stb0899, stb6100 >> or >> >> lnbp21 code. >> > >> > Problem solved with the patch below. >> > >> > I found that both problems tuning channels (#1 immediately after boot >> and >> > #2 after sleep) are >> > caused by the lnbp21 voltage OFF setting. To fix #1: the LNB voltage >> needs >> > to be turned on when >> > the lnbp21 is attached, and to fix #2: turning the voltage off on >> sleep >> > needs to be disabled. >> > >> > To keep the voltage on, we need to make sure that register bit >> LNBP21_EN >> > is always set. >> > >> > I note that as well as controlling the voltage regulator blocks this >> > register bit also controls >> > a loopthrough switch -- clearing the bit takes the lnbp21 out of the >> LNB >> > line, which could be >> > used to allow other circuitry to do LNB power and control. I don't >> have >> > any info on how the >> > card is actually wired. It seems best to keep the EN bit always set, >> > because I know clearing >> > it causes trouble. >> > >> > It turns out there is already a mechanism for specifying register bits >> to >> > be overridden in >> > the lnbp21 attach call (already used for another card) and we just >> need >> to >> > apply the following >> > one-line patch to the VP-1041 attach. >> > >> > This is against the repository at >> > http://mercurial.intuxication.org/hg/s2-liplianin. >> > >> > Signed-off-by: Hans Werner <hwerner4@xxxxxx> >> > >> > diff -r 28324bc3d694 linux/drivers/media/dvb/mantis/mantis_dvb.c >> > --- a/linux/drivers/media/dvb/mantis/mantis_dvb.c >> > +++ b/linux/drivers/media/dvb/mantis/mantis_dvb.c >> > @@ -239,7 +239,7 @@ int __devinit mantis_frontend_init(struc >> > vp1041_config.demod_address); >> > >> > if (stb6100_attach(mantis->fe, >> > &vp1041_stb6100_config, &mantis->adapter)) { >> > - if (!lnbp21_attach(mantis->fe, >> > &mantis->adapter, 0, 0)) { >> > + if (!lnbp21_attach(mantis->fe, >> > &mantis->adapter, LNBP21_EN, 0)) { >> > printk("%s: No LNBP21 >> found!\n", >> > __FUNCTION__); >> > mantis->fe = NULL; >> > } >> > >> > >> > >> > Regards, >> > Hans > > -- > Release early, release often. > > Psssst! Schon vom neuen GMX MultiMessenger gehört? Der kann`s mit allen: > http://www.gmx.net/de/go/multimessenger > > > _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
