> Tom, Jackden, > > Please find attached a patch that should add support for the DVB side > of this card. Please follow the following to the dot and provide the > outputs requested, this will ensure that I capture all possible issues > as soon as possible (and yes I do expect at least one issue). > > 1) Ensure that you have everything installed to build the v4l-dvb tree > (usually the kernel headers, build-essentials and patch) > > 2) Download and extract: > http://linuxtv.org/hg/~stoth/cx23885- > leadtek/archive/837860b92af5.tar.bz2 > > 3) Download attached patch to the same directory as the above file. > > 4) Open up a terminal into the directory of the extracted files and > apply the patch with this > command: > patch -p1 < ../Compro_VideoMate_E650.patch > > 5) Make, install: > make; > sudo make install > > 6) Download the firmware (see > http://linuxtv.org/wiki/index.php/Xceive_XC3028/XC2028#How_to_Obtain_th > e_Firmware) > > 7) Now this is going to sound weird (for linux) but it puts the card in > a known state for me to work from: > Turn the computer off, count to 10 and turn back on (no a reset will > not do what I need). Ensure windows does NOT load, before going into > Linux, if it does turn it back off again. > > 8) Provide the dmesg for the lines after: > "Linux video capture interface: v2.00" > > 9) If no errors try scanning for channels (see > http://linuxtv.org/wiki/index.php/Scan if you are unsure how do this). > If this outputs tv channels then so far so good. > > 10) Open up your favourite player (ensure the channels config is the > correct directory e.g. for xine ~/.xine/) and try and watch a channel. > > 11) Provide output of dmesg (only the continuation from the previous > dmesg output). > > Now if at any stage it doesn't work here are a few things that you can > try (make sure you let me know which ones you did try): > a) Perform a computer restart (soft restart - a restart controlled by > the computer, not using any of the buttons on the front), and load > windows ensure the card is working by tuning to DVB and then perform a > soft restart into linux and resume at step above that caused errors. > This is typically going to solve an issue where you cannot get past > step 9. > > b) Turn debugging on for the following modules: > tuner_xc2028 > cx23885 > zl10353 > This is usually performed in: /etc/modprobe.d/options (this is what > ubuntu has) by setting debug = 1. An example line is: > options cx23885 debug=1 > Now go back to step 7 and try again when you run into a error message > or unable to do the above provide the dmesg output as referred to in > Step 11. > > Thanks > > Stephen > > > -- > Nothing says Labor Day like 500hp of American muscle Visit OnCars.com > today. Stephen, Thanks for the latest patch. FYI, I had previously been experimenting with the Dvico card source so to remove any of the changes I had made I did the following: hg clone http://linuxtv.org/hg/v4l-dvb cd v4l-dvb make sudo make install I then followed your instructions and restarted the PC after 10 second delay. Please see below for output. In terms of debugging I am unable to do a soft restart as I need to swap drives over. I did however enable debugging and you can see the output of dmesg at the end of the email. Outfrom dmesg: [ 32.244477] Linux video capture interface: v2.00 [ 32.270595] cx23885 driver version 0.0.1 loaded [ 32.270640] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 32.270651] CORE cx23885[0]: subsystem: 185b:e800, board: Compro VideoMate E650 [card=13,autodetected] [ 32.443275] cx23885[0]: i2c bus 0 registered [ 32.443288] cx23885[0]: i2c bus 1 registered [ 32.443299] cx23885[0]: i2c bus 2 registered [ 32.470204] cx23885[0]: cx23885 based dvb card [ 32.471207] lirc_dev: IR Remote Control driver registered, major 61 [ 32.477659] lirc_imon: no version for "lirc_unregister_plugin" found: kernel tainted. [ 32.478369] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: Driver for Soundgraph iMON MultiMedia IR/VFD, v0.3 [ 32.478370] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: Venky Raju <dev@xxxxxxxx> [ 32.478392] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: imon_probe: found IMON device [ 32.478396] lirc_dev: lirc_register_plugin: sample_rate: 0 [ 32.478408] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: imon_probe: Registered iMON plugin(minor:0) [ 32.478432] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: imon_probe: iMON device on usb<5:2> initialized [ 32.478437] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: imon_probe: found IMON device [ 32.478439] lirc_dev: lirc_register_plugin: sample_rate: 0 [ 32.478448] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: imon_probe: Registered iMON plugin(minor:1) [ 32.478461] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: imon_probe: iMON device on usb<5:2> initialized [ 32.478470] usbcore: registered new interface driver lirc_imon [ 32.648252] nvidia: module license 'NVIDIA' taints kernel. [ 32.943549] usbcore: registered new interface driver hiddev [ 32.949197] input: Logitech Logitech BT Mini-Receiver as /devices/pci0000:00/0000:00:1a.2/usb3/3-2/3-2.2/3-2.2:1.0/input/input4 [ 32.996828] input,hidraw0: USB HID v1.11 Keyboard [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1a.2-2.2 [ 33.008109] input: Logitech Logitech BT Mini-Receiver as /devices/pci0000:00/0000:00:1a.2/usb3/3-2/3-2.3/3-2.3:1.0/input/input5 [ 33.016231] dib0700: loaded with support for 7 different device-types [ 33.016463] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 33.023429] xc2028 1-0061: creating new instance [ 33.023431] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 33.023434] DVB: registering new adapter (cx23885[0]) [ 33.023436] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... [ 33.023570] cx23885_dev_checkrevision() Hardware revision = 0xb0 [ 33.023576] cx23885[0]/0: found at 0000:04:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfe800000 [ 33.023581] PCI: Setting latency timer of device 0000:04:00.0 to 64 [ 33.023821] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 33.023826] PCI: Setting latency timer of device 0000:01:00.0 to 64 [ 33.023961] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.09 Wed Jun 4 23:43:17 PDT 2008 [ 33.025495] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 33.025510] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 33.058794] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... [ 33.071378] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw' [ 33.080751] input,hiddev96,hidraw1: USB HID v1.11 Mouse [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1a.2-2.3 [ 33.080763] usbcore: registered new interface driver usbhid [ 33.080771] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 33.277932] usbcore: registered new interface driver dvb_usb_dib0700 [ 33.611862] lp: driver loaded but no devices found [ 33.656757] w83627ehf: Found W83627DHG chip at 0x290 [ 33.679680] coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong! [ 33.679707] coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong! [ 33.889981] Adding 9847804k swap on /dev/sda5. Priority:-1 extents:1 across:9847804k [ 34.561845] EXT3 FS on sda1, internal journal [ 36.015617] ip_tables: (C) 2000-2006 Netfilter Core Team [ 36.302264] CIFS VFS: Error connecting to IPv4 socket. Aborting operation [ 36.302267] CIFS VFS: cifs_mount failed w/return code = -101 [ 36.305803] CIFS VFS: Error connecting to IPv4 socket. Aborting operation [ 36.305806] CIFS VFS: cifs_mount failed w/return code = -101 [ 36.309144] CIFS VFS: Error connecting to IPv4 socket. Aborting operation [ 36.309147] CIFS VFS: cifs_mount failed w/return code = -101 [ 37.078803] No dock devices found. [ 39.171426] NET: Registered protocol family 10 [ 39.171563] lo: Disabled Privacy Extensions [ 40.824135] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 40.824138] apm: disabled - APM is not SMP safe. [ 49.068260] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex [ 53.170602] NET: Registered protocol family 17 [ 63.167854] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: VFD port opened [ 64.725185] eth0: no IPv6 routers present [ 65.009138] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: IR port opened [ 67.652311] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: IR port opened Output from scan: root@quark:~# scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Perth > /root/.tzap/channels.conf scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/au-Perth using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 226500000 1 3 9 3 1 1 0 initial transponder 177500000 1 2 9 3 1 1 0 initial transponder 191625000 1 3 9 3 1 1 0 initial transponder 219500000 1 3 9 3 1 1 0 initial transponder 536500000 1 2 9 3 1 2 0 >>> tune to: 226500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSIO N_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSIO N_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 191625000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSIO N_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 219500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_3_4:FEC_AUTO:QAM_64:TRANSMISSIO N_MODE_8K:GUARD_INTERVAL_1_16:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 >>> tune to: 536500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSIO N_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 dumping lists (0 services) Done. I then tried to tune to channels using the MythTV backend setup. I was able to add the card but when I tried to scan all Australian channels none were detected. I then added the debugging option as requested and rebooted with 10 second power off on power supply switch ie no power to backplane. With Debugging On: root@quark:/etc/modprobe.d# cat cx23885 options cx23885 debug=1 root@quark:/etc/modprobe.d# cat zl10353 options zl10353 debug=1 root@quark:/etc/modprobe.d# cat tuner_xc2028 options tuner_xc2028 debug=1 Output from dmesg: [ 32.350547] Linux video capture interface: v2.00 [ 32.380727] input,hidraw0: USB HID v1.11 Keyboard [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1a.2-2.2 [ 32.392016] input: Logitech Logitech BT Mini-Receiver as /devices/pci0000:00/0000:00:1a.2/usb3/3-2/3-2.3/3-2.3:1.0/input/input5 [ 32.397767] cx23885 driver version 0.0.1 loaded [ 32.397809] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 32.397812] cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type 885 [ 32.397814] cx23885[0]/0: cx23885_init_tsport(portno=2) [ 32.397820] CORE cx23885[0]: subsystem: 185b:e800, board: Compro VideoMate E650 [card=13,autodetected] [ 32.397822] cx23885[0]/0: cx23885_pci_quirks() [ 32.397825] cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0 [ 32.397827] cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0 [ 32.397828] cx23885[0]/0: cx23885_reset() [ 32.497035] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A] [ 32.497045] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2] [ 32.497046] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B] [ 32.497060] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4] [ 32.497061] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5] [ 32.497063] cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C] [ 32.497076] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7] [ 32.497077] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8] [ 32.497079] cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9] [ 32.536923] cx23885[0]: i2c bus 0 registered [ 32.536934] cx23885[0]: i2c bus 1 registered [ 32.536944] cx23885[0]: i2c bus 2 registered [ 32.563751] cx23885[0]: cx23885 based dvb card [ 32.596552] dib0700: loaded with support for 7 different device-types [ 32.596619] dvb-usb: found a 'Hauppauge Nova-T 500 Dual DVB-T' in cold state, will try to load a firmware [ 32.624555] input,hiddev96,hidraw1: USB HID v1.11 Mouse [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1a.2-2.3 [ 32.624568] usbcore: registered new interface driver usbhid [ 32.624571] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 32.640555] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw' [ 32.692348] xc2028: Xcv2028/3028 init called! [ 32.692351] xc2028 1-0061: creating new instance [ 32.692352] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 32.692354] xc2028 1-0061: xc2028_set_config called [ 32.692357] DVB: registering new adapter (cx23885[0]) [ 32.692359] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... [ 32.692507] cx23885_dev_checkrevision() Hardware revision = 0xb0 [ 32.692513] cx23885[0]/0: found at 0000:04:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfe800000 [ 32.692519] PCI: Setting latency timer of device 0000:04:00.0 to 64 [ 32.850867] usbcore: registered new interface driver dvb_usb_dib0700 [ 33.092528] lp: driver loaded but no devices found [ 33.137196] w83627ehf: Found W83627DHG chip at 0x290 [ 33.160472] coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong! [ 33.160499] coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong! [ 33.403690] Adding 9847804k swap on /dev/sda5. Priority:-1 extents:1 across:9847804k [ 34.064500] EXT3 FS on sda1, internal journal [ 35.529326] ip_tables: (C) 2000-2006 Netfilter Core Team [ 35.771602] CIFS VFS: Error connecting to IPv4 socket. Aborting operation [ 35.771606] CIFS VFS: cifs_mount failed w/return code = -101 [ 35.775091] CIFS VFS: Error connecting to IPv4 socket. Aborting operation [ 35.775094] CIFS VFS: cifs_mount failed w/return code = -101 [ 35.778450] CIFS VFS: Error connecting to IPv4 socket. Aborting operation [ 35.778453] CIFS VFS: cifs_mount failed w/return code = -101 [ 36.537404] No dock devices found. [ 38.596444] NET: Registered protocol family 10 [ 38.596583] lo: Disabled Privacy Extensions [ 40.138256] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 40.138258] apm: disabled - APM is not SMP safe. [ 47.368015] zl10353: zl10353_calc_nominal_rate: bw 7, adc_clock 450560 => 0x5ae9 [ 47.368694] zl10353: zl10353_calc_input_freq: if2 45600, ife 45600, adc_clock 450560 => -6633 / 0xe617 [ 47.370382] xc2028 1-0061: xc2028_set_params called [ 47.370384] xc2028 1-0061: generic_set_freq called [ 47.370387] xc2028 1-0061: should set frequency 219500 kHz [ 47.370388] xc2028 1-0061: check_firmware called [ 47.370390] xc2028 1-0061: load_all_firmwares called [ 47.370392] xc2028 1-0061: Reading firmware xc3028-v27.fw [ 47.385345] xc2028 1-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 [ 47.385355] xc2028 1-0061: Reading firmware type BASE F8MHZ (3), id 0, size=8718. [ 47.385363] xc2028 1-0061: Reading firmware type BASE F8MHZ MTS (7), id 0, size=8712. [ 47.385373] xc2028 1-0061: Reading firmware type BASE FM (401), id 0, size=8562. [ 47.385381] xc2028 1-0061: Reading firmware type BASE FM INPUT1 (c01), id 0, size=8576. [ 47.385389] xc2028 1-0061: Reading firmware type BASE (1), id 0, size=8706. [ 47.385397] xc2028 1-0061: Reading firmware type BASE MTS (5), id 0, size=8682. [ 47.385403] xc2028 1-0061: Reading firmware type (0), id 100000007, size=161. [ 47.385406] xc2028 1-0061: Reading firmware type MTS (4), id 100000007, size=169. [ 47.385409] xc2028 1-0061: Reading firmware type (0), id 200000007, size=161. [ 47.385412] xc2028 1-0061: Reading firmware type MTS (4), id 200000007, size=169. [ 47.385415] xc2028 1-0061: Reading firmware type (0), id 400000007, size=161. [ 47.385418] xc2028 1-0061: Reading firmware type MTS (4), id 400000007, size=169. [ 47.385422] xc2028 1-0061: Reading firmware type (0), id 800000007, size=161. [ 47.385425] xc2028 1-0061: Reading firmware type MTS (4), id 800000007, size=169. [ 47.385428] xc2028 1-0061: Reading firmware type (0), id 3000000e0, size=161. [ 47.385431] xc2028 1-0061: Reading firmware type MTS (4), id 3000000e0, size=169. [ 47.385434] xc2028 1-0061: Reading firmware type (0), id c000000e0, size=161. [ 47.385437] xc2028 1-0061: Reading firmware type MTS (4), id c000000e0, size=169. [ 47.385440] xc2028 1-0061: Reading firmware type (0), id 200000, size=161. [ 47.385443] xc2028 1-0061: Reading firmware type MTS (4), id 200000, size=169. [ 47.385446] xc2028 1-0061: Reading firmware type (0), id 4000000, size=161. [ 47.385448] xc2028 1-0061: Reading firmware type MTS (4), id 4000000, size=169. [ 47.385451] xc2028 1-0061: Reading firmware type D2633 DTV6 ATSC (10030), id 0, size=149. [ 47.385455] xc2028 1-0061: Reading firmware type D2620 DTV6 QAM (68), id 0, size=149. [ 47.385459] xc2028 1-0061: Reading firmware type D2633 DTV6 QAM (70), id 0, size=149. [ 47.385463] xc2028 1-0061: Reading firmware type D2620 DTV7 (88), id 0, size=149. [ 47.385467] xc2028 1-0061: Reading firmware type D2633 DTV7 (90), id 0, size=149. [ 47.385470] xc2028 1-0061: Reading firmware type D2620 DTV78 (108), id 0, size=149. [ 47.385474] xc2028 1-0061: Reading firmware type D2633 DTV78 (110), id 0, size=149. [ 47.385477] xc2028 1-0061: Reading firmware type D2620 DTV8 (208), id 0, size=149. [ 47.385480] xc2028 1-0061: Reading firmware type D2633 DTV8 (210), id 0, size=149. [ 47.385483] xc2028 1-0061: Reading firmware type FM (400), id 0, size=135. [ 47.385487] xc2028 1-0061: Reading firmware type (0), id 10, size=161. [ 47.385489] xc2028 1-0061: Reading firmware type MTS (4), id 10, size=169. [ 47.385493] xc2028 1-0061: Reading firmware type (0), id 1000400000, size=169. [ 47.385496] xc2028 1-0061: Reading firmware type (0), id c00400000, size=161. [ 47.385499] xc2028 1-0061: Reading firmware type (0), id 800000, size=161. [ 47.385501] xc2028 1-0061: Reading firmware type (0), id 8000, size=161. [ 47.385504] xc2028 1-0061: Reading firmware type LCD (1000), id 8000, size=161. [ 47.385507] xc2028 1-0061: Reading firmware type LCD NOGD (3000), id 8000, size=161. [ 47.385510] xc2028 1-0061: Reading firmware type MTS (4), id 8000, size=169. [ 47.385513] xc2028 1-0061: Reading firmware type (0), id b700, size=161. [ 47.385516] xc2028 1-0061: Reading firmware type LCD (1000), id b700, size=161. [ 47.385519] xc2028 1-0061: Reading firmware type LCD NOGD (3000), id b700, size=161. [ 47.385522] xc2028 1-0061: Reading firmware type (0), id 2000, size=161. [ 47.385525] xc2028 1-0061: Reading firmware type MTS (4), id b700, size=169. [ 47.385528] xc2028 1-0061: Reading firmware type MTS LCD (1004), id b700, size=169. [ 47.385531] xc2028 1-0061: Reading firmware type MTS LCD NOGD (3004), id b700, size=169. [ 47.385535] xc2028 1-0061: Reading firmware type SCODE HAS_IF_3280 (60000000), id 0, size=192. [ 47.385539] xc2028 1-0061: Reading firmware type SCODE HAS_IF_3300 (60000000), id 0, size=192. [ 47.385543] xc2028 1-0061: Reading firmware type SCODE HAS_IF_3440 (60000000), id 0, size=192. [ 47.385546] xc2028 1-0061: Reading firmware type SCODE HAS_IF_3460 (60000000), id 0, size=192. [ 47.385550] xc2028 1-0061: Reading firmware type DTV6 ATSC OREN36 SCODE HAS_IF_3800 (60210020), id 0, size=192. [ 47.385555] xc2028 1-0061: Reading firmware type SCODE HAS_IF_4000 (60000000), id 0, size=192. [ 47.385558] xc2028 1-0061: Reading firmware type DTV6 ATSC TOYOTA388 SCODE HAS_IF_4080 (60410020), id 0, size=192. [ 47.385565] xc2028 1-0061: Reading firmware type SCODE HAS_IF_4200 (60000000), id 0, size=192. [ 47.385568] xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_4320 (60008000), id 8000, size=192. [ 47.385573] xc2028 1-0061: Reading firmware type SCODE HAS_IF_4450 (60000000), id 0, size=192. [ 47.385576] xc2028 1-0061: Reading firmware type MTS LCD NOGD MONO IF SCODE HAS_IF_4500 (6002b004), id b700, size=192. [ 47.385582] xc2028 1-0061: Reading firmware type LCD NOGD IF SCODE HAS_IF_4600 (60023000), id 8000, size=192. [ 47.385587] xc2028 1-0061: Reading firmware type DTV6 QAM DTV7 DTV78 DTV8 ZARLINK456 SCODE HAS_IF_4760 (620003e0), id 0, size=192. [ 47.385593] xc2028 1-0061: Reading firmware type SCODE HAS_IF_4940 (60000000), id 0, size=192. [ 47.385596] xc2028 1-0061: Reading firmware type SCODE HAS_IF_5260 (60000000), id 0, size=192. [ 47.385600] xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_5320 (60008000), id f00000007, size=192. [ 47.385604] xc2028 1-0061: Reading firmware type DTV7 DTV78 DTV8 DIBCOM52 CHINA SCODE HAS_IF_5400 (65000380), id 0, size=192. [ 47.385610] xc2028 1-0061: Reading firmware type DTV6 ATSC OREN538 SCODE HAS_IF_5580 (60110020), id 0, size=192. [ 47.385615] xc2028 1-0061: Reading firmware type SCODE HAS_IF_5640 (60000000), id 300000007, size=192. [ 47.385619] xc2028 1-0061: Reading firmware type SCODE HAS_IF_5740 (60000000), id c00000007, size=192. [ 47.385623] xc2028 1-0061: Reading firmware type SCODE HAS_IF_5900 (60000000), id 0, size=192. [ 47.385626] xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6000 (60008000), id c04c000f0, size=192. [ 47.385631] xc2028 1-0061: Reading firmware type DTV6 QAM ATSC LG60 F6MHZ SCODE HAS_IF_6200 (68050060), id 0, size=192. [ 47.385637] xc2028 1-0061: Reading firmware type SCODE HAS_IF_6240 (60000000), id 10, size=192. [ 47.385640] xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6320 (60008000), id 200000, size=192. [ 47.385644] xc2028 1-0061: Reading firmware type SCODE HAS_IF_6340 (60000000), id 200000, size=192. [ 47.385648] xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6500 (60008000), id c044000e0, size=192. [ 47.385653] xc2028 1-0061: Reading firmware type DTV6 ATSC ATI638 SCODE HAS_IF_6580 (60090020), id 0, size=192. [ 47.385659] xc2028 1-0061: Reading firmware type SCODE HAS_IF_6600 (60000000), id 3000000e0, size=192. [ 47.385663] xc2028 1-0061: Reading firmware type MONO SCODE HAS_IF_6680 (60008000), id 3000000e0, size=192. [ 47.385667] xc2028 1-0061: Reading firmware type DTV6 ATSC TOYOTA794 SCODE HAS_IF_8140 (60810020), id 0, size=192. [ 47.385672] xc2028 1-0061: Reading firmware type SCODE HAS_IF_8200 (60000000), id 0, size=192. [ 47.385681] xc2028 1-0061: Firmware files loaded. [ 47.385683] xc2028 1-0061: checking firmware, user requested type=F8MHZ D2620 DTV7 (8a), id 0000000000000000, int_freq 4760, scode_nr 0 [ 47.583956] xc2028 1-0061: load_firmware called [ 47.583958] xc2028 1-0061: seek_firmware called, want type=BASE F8MHZ D2620 DTV7 (8b), id 0000000000000000. [ 47.583961] xc2028 1-0061: Found firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 47.583964] xc2028 1-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 48.726038] xc2028 1-0061: Load init1 firmware, if exists [ 48.726041] xc2028 1-0061: load_firmware called [ 48.726043] xc2028 1-0061: seek_firmware called, want type=BASE INIT1 F8MHZ D2620 DTV7 (408b), id 0000000000000000. [ 48.726048] xc2028 1-0061: Can't find firmware for type=BASE INIT1 F8MHZ (4003), id 0000000000000000. [ 48.726051] xc2028 1-0061: load_firmware called [ 48.726052] xc2028 1-0061: seek_firmware called, want type=BASE INIT1 D2620 DTV7 (4089), id 0000000000000000. [ 48.726055] xc2028 1-0061: Can't find firmware for type=BASE INIT1 (4001), id 0000000000000000. [ 48.726058] xc2028 1-0061: load_firmware called [ 48.726059] xc2028 1-0061: seek_firmware called, want type=F8MHZ D2620 DTV7 (8a), id 0000000000000000. [ 48.726062] xc2028 1-0061: Found firmware for type=D2620 DTV7 (88), id 0000000000000000. [ 48.726065] xc2028 1-0061: Loading firmware for type=D2620 DTV7 (88), id 0000000000000000. [ 48.739823] xc2028 1-0061: Trying to load scode 0 [ 48.739825] xc2028 1-0061: load_scode called [ 48.739827] xc2028 1-0061: Loading SCODE for type=DTV6 QAM DTV7 DTV78 DTV8 ZARLINK456 SCODE HAS_IF_4760 (620003e0), id 0000000000000000. [ 48.769126] xc2028 1-0061: xc2028_get_reg 0004 called [ 48.769846] xc2028 1-0061: xc2028_get_reg 0008 called [ 48.770558] xc2028 1-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 48.870205] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex [ 48.907994] xc2028 1-0061: divisor= 00 00 36 30 (freq=219.500) [ 51.786851] NET: Registered protocol family 17 [ 63.368864] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: VFD port opened [ 65.272619] eth0: no IPv6 routers present [ 65.331954] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: IR port opened [ 67.864414] /home/tom/source/lirc/drivers/lirc_imon/lirc_imon.c: IR port opened Again thanks for your help and please let me know if you want me to try something else. Tom _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
