Re: Pinnacle PCTV Dual DVB-T Diversity Stick built in IR-Receiver supported ?

["SUBHRANIL CHOUDHURY" <subhra85@xxxxxxxxx>]

hi,

I am working on DVB-T for the first time. I am using a Pinnacle PCTV 2001e USB DVB-T dongle.In that the device dri vers are getting registered and the device is getting detected.I am using a 2.6.23.15 kernel.

 

The dmesg is as follows:

 

dvb-usb: Pinnacle PCTV Dual DVB-T Diversity Stick successfully deinitialized and disconnected.
usb 1-1.4: new high speed USB device using musb_hdrc and address 4
usb 1-1.4: Product: PCTV 2001e
usb 1-1.4: Manufacturer: PINNACLE
usb 1-1.4: SerialNumber: 12020607
usb 1-1.4: configuration #1 chosen from 1 choice
dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
DVB: registering frontend 0 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
DVB: registering frontend 1 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: Pinnacle PCTV Dual DVB-T Diversity Stick successfully initialized and connected.

 

But, after that when i am trying to run any scan application , it is showing "scan failed".

 

the dmesg after running scan application is,

 

APPLN INFO >> Inside scan_network
APPLN INFO >> Inside tune_initial
Inside alloc_transponder
initial transponder 474166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 498166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 522166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 538166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 562166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 586166000 0 3 9 3 1 2 0
Inside alloc_transponder
initial transponder 714166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 738166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 754166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 762166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 786166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 810166000 0 2 9 3 1 0 0
Inside tune_to_next_transponder()
Inside tune_to_transponder()
APPLN INFO >> Entered __tune_to_transponder()
>>> tune to: 474166000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: >>> tuning failed!!!
APPLN INFO >> Entered __tune_to_transponder()
>>> tune to: 474166000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE (tuning failed)
WARNING: >>> tuning failed!!!
Inside tune_to_transponder()

etc, etc.

 

Can Anyone Please tell me if you have faced a similar problem or what is happening ?

Do i have to add something to the kernel?

 

Best regards,

subhro
___________________________________________________________________________________________________________________

On Sat, Jul 12, 2008 at 11:36 PM, Ingo Arndt <scachi@xxxxxx> wrote:

Hello,

as I haven't received any answer yet I'll post my question again,

I have a Pinnacle PCTV Dual DVB-T Diversity Stick which works fine.
The only thing I am missing is the built-in infrared receiver which is not recognized.

Is anyone using this Pinnacle DVB-T stick and got it's remote control working ?

Am I missing a module, a module option or something else
or is the ir receiver just not supported by now ?

I use the kernel 2.6.25 with tuxonice-patches on archlinux.

lsusb output:
------------------------- lsusb output start ---
idVendor           0x2304 Pinnacle Systems, Inc. [hex]
 idProduct          0x0229
 bcdDevice            0.01
 iManufacturer           1 PINNACLE
 iProduct                2 PCTV 2001e
 iSerial                 3 12027630
------------------------- lsusb output stop ---


mesg output:
---------------- dmesg code start ---
usb 7-3: new high speed USB device using ehci_hcd and address 9
usb 7-3: configuration #1 chosen from 1 choice
dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
DVB: registering frontend 0 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
DVB: registering frontend 1 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: Pinnacle PCTV Dual DVB-T Diversity Stick successfully
initialized and connected.
----------------- dmesg code end ---


Best regards,
 Ingo

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb