>>On Nov 13, 2007 11:16 AM, aldebaran <aldebx at yahoo.fr>> wrote: >>>> >>>> I thank you very much for your quick reply Michel, Markus and Mauro!! >> >>[snip] >> >> [ 789.484000] cx23885 driver version 0.0.1 loaded >> [ 789.484000] ACPI: PCI Interrupt 0000:04:00.0[A] ->> GSI 17 (level, low) >> ->> IRQ 17 >> [ 789.484000] CORE cx23885[0]: subsystem: 0070:7717, board: Hauppauge >> WinTV-HVR1800lp [card=1,insmod option] >> [ 789.584000] cx23885[0]: i2c bus 0 registered >> [ 789.584000] cx23885[0]: i2c bus 1 registered >> [ 789.584000] cx23885[0]: i2c bus 2 registered >> [ 789.612000] tveeprom 0-0050: Hauppauge model 77001, rev D4C0, serial# >> 2335707 >> [ 789.612000] tveeprom 0-0050: MAC address is 00-0D-FE-23-A3-DB >> [ 789.612000] tveeprom 0-0050: tuner model is Xceive XC3028 (idx 120, type >> 71) >> [ 789.612000] tveeprom 0-0050: TV standards NTSC(M) ATSC/DVB Digital >> (eeprom 0x88) >> [ 789.612000] tveeprom 0-0050: audio processor is CX23885 (idx 39) >> [ 789.612000] tveeprom 0-0050: decoder processor is CX23885 (idx 33) >> [ 789.612000] tveeprom 0-0050: has no radio, has no IR receiver, has no IR >> transmitter >> [ 789.612000] cx23885[0]: hauppauge eeprom: model=77001 >> [ 789.612000] cx23885[0]: cx23885 based dvb card >> [ 789.624000] cx23885[0]: frontend initialization failed >> [ 789.624000] cx23885_dvb_register() dvb_register failed err = -1 >> [ 789.624000] cx23885_dev_setup() Failed to register dvb adapters on VID_C >> [ 789.624000] cx23885[0]/0: found at 0000:04:00.0, rev: 2, irq: 17, >> latency: 0, mmio: 0xf4000000 >> [ 789.624000] PCI: Setting latency timer of device 0000:04:00.0 to 64 > >Don't worry about this -- Steve's got it covered: > >http://linuxtv.org/pipermail/linux-dvb/2007-November/021863.html > >-mike Hi I've just joined this list because I have a HP Expresscard Digital/Analog tuner and it looks like it's the same card referred to previously in this thread, which apparently is a rebranded Hauppauge card. So far I havent been able to get it to work but since I dont really know what I'm doing I though I'd better ask for help. What I've done so far is as follows: got the source: hg clone http://linuxtv.org/hg/v4l-dvb make make install reboot then dmesg gives me this: [ 18.520000] CORE cx23885[0]: subsystem: 0070:7717, board: Hauppauge WinTV-HVR1500 [card=6,autodetected] [ 18.628000] cx23885[0]: i2c bus 0 registered [ 18.628000] cx23885[0]: i2c bus 1 registered [ 18.628000] cx23885[0]: i2c bus 2 registered [ 18.652000] tveeprom 0-0050: Hauppauge model 77001, rev D3C0, serial# 837872 [ 18.652000] tveeprom 0-0050: MAC address is 00-0D-FE-0C-C8-F0 [ 18.652000] tveeprom 0-0050: tuner model is Xceive XC3028 (idx 120, type 71) [ 18.652000] tveeprom 0-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88) [ 18.652000] tveeprom 0-0050: audio processor is CX23885 (idx 39) [ 18.652000] tveeprom 0-0050: decoder processor is CX23885 (idx 33) [ 18.652000] tveeprom 0-0050: has no radio, has no IR receiver, has no IR transmitter [ 18.652000] cx23885[0]: hauppauge eeprom: model=77001 [ 18.652000] cx23885[0]: cx23885 based dvb card [ 18.652000] ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.2mp.ubuntu1 [ 18.652000] ipw3945: Copyright(c) 2003-2006 Intel Corporation [ 18.872000] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner [ 18.872000] DVB: registering new adapter (cx23885[0]) [ 18.872000] DVB: registering frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)... [ 18.876000] cx23885_dev_checkrevision() Hardware revision = 0xb0 [ 18.876000] cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 17, latency: 0, mmio: 0xd8000000 [ 18.876000] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 18.876000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21 [ 18.876000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 19.056000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 19.056000] PCI: Setting latency timer of device 0000:02:00.0 to 64 Unlike the previous poster I'm not getting "frontend initialization failed" which is promising, but when I run: /usr/bin/scan /usr/share/doc/dvb-utils/examples/scan/atsc/us-ATSC-center-frequencies-8VSB I get a bunch of "tuning failed" messages like this: scanning /usr/share/doc/dvb-utils/examples/scan/atsc/us-ATSC-center-frequencies-8VSB using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' >>> tune to: 57028615:8VSB WARNING: >>> tuning failed!!! >>> tune to: 57028615:8VSB (tuning failed) WARNING: >>> tuning failed!!! Am I missing something (like firmware perhaps) or does it not work yet? Let me know if there's anything I can do to help get it working. Thanks in advance. John PS Also, thanks for all the hard work done so far! _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
