By the way, what does it mean moi and moikka? Hello in finish?
Albert
2008/2/18, Antti Palosaari <crope@xxxxxx>:
latest v4l-master + patch you give.
regards
Antti
Albert Comerma wrote:
> Uhm... that's strange, I don't have any of this cards to test, but other
> people reported that this solution was working. Could you post the
> dib0700_devices.c you're using to have a look?
>
> Albert
>
> 2008/2/18, Antti Palosaari <crope@xxxxxx <mailto:crope@xxxxxx>>:
>
> moi
> It does not work for me. It says same PID-filter timeout as I have got
> earlier. I don't have amplified antenna now, but I can say that all
> other DVB-T sticks I have are working with this small antenna. It could
> be that sensitivity of this hardware is bad or there is something wrong
> with driver or firmware. Lets try to test it Windows to see if it is
> working or not.
> Logs attached.
>
>
> regards
> Antti
>
> Albert Comerma wrote:
>
> > Hey people, we already solved this problems. I submitted a patch
> a few
> > days ago, but I think it's not on the current sources. I send
> again the
> > patch. Basically it must use the same frontend description as
> asus cards.
> >
> > Albert
> >
>
> > 2008/2/18, Antti Palosaari <crope@xxxxxx <mailto:crope@xxxxxx>
> <mailto:crope@xxxxxx <mailto:crope@xxxxxx>>>:
>
> >
> > moikka
> > I have also this device (express card). I haven't looked
> inside yet, but
> > I think there is DibCOM STK7700D (in my understanding dual
> demod chip)
> > and only *one* MT2266 tuner. I tried various GPIO settings but no
> > luck yet.
> > GPIO6 is for MT2266.
> > GPIO9 and GPIO10 are for frontend.
> >
> > Looks like tuner goes to correct frequency because I got always
> > PID-filter timeouts when tuning to correct freq. I will now
> try to take
> > some usb-sniffs to see configuration used. Any help is welcome.
> >
> > regards
> > Antti
> >
> > Albert Comerma wrote:
> > > Hi!, with Michel (mm-sl@xxxxxxxxxxxxx
> <mailto:mm-sl@xxxxxxxxxxxxx>
>
> > <mailto:mm-sl@xxxxxxxxxxxxx <mailto:mm-sl@xxxxxxxxxxxxx>>
> <mailto:mm-sl@xxxxxxxxxxxxx <mailto:mm-sl@xxxxxxxxxxxxx>
>
> > <mailto:mm-sl@xxxxxxxxxxxxx <mailto:mm-sl@xxxxxxxxxxxxx>>>) who
> >
> > > is a owner of this Yuan card we added the device to
> > dib0700_devices, and
> > > we got it recognized without problems. The only problem is
> that no
> > > channel is detected on scan on kaffeine or other software... I
> > post some
> > > dmesg. We don't know where it may be the problem... or how to
> > detect it...
> > >
> > > usb 4-2: new high speed USB device using ehci_hcd and
> address 6
> > > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > > usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> > > usb 4-2: Product: STK7700D
> > > usb 4-2: Manufacturer: YUANRD
> > > usb 4-2: SerialNumber: 0000000001
> > > usb 4-2: configuration #1 chosen from 1 choice
> > > dvb-usb: found a 'Yuan EC372S' in cold state, will try to
> load a
> > firmware
> > > dvb-usb: downloading firmware from file
> 'dvb-usb-dib0700-1.10.fw'
> > > dib0700: firmware started successfully.
> > > dvb-usb: found a 'Yuan EC372S' in warm state.
> > > dvb-usb: will pass the complete MPEG2 transport stream to the
> > software
> > > demuxer.
> > > DVB: registering new adapter (Yuan EC372S)
> > > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > > dvb-usb: will pass the complete MPEG2 transport stream to the
> > software
> > > demuxer.
> > > DVB: registering new adapter (Yuan EC372S)
> > > DVB: registering frontend 1 (DiBcom 7000PC)...
> > > MT2266: successfully identified
> > > input: IR-receiver inside an USB DVB receiver as
> /class/input/input10
> > > dvb-usb: schedule remote query interval to 150 msecs.
> > > dvb-usb: Yuan EC372S successfully initialized and connected.
> > >
> > >
> >
> > >
> >
> ------------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > linux-dvb mailing list
>
> > > linux-dvb@xxxxxxxxxxx <mailto:linux-dvb@xxxxxxxxxxx>
> <mailto:linux-dvb@xxxxxxxxxxx <mailto:linux-dvb@xxxxxxxxxxx>>
>
> > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
> >
> >
> > --
> > http://palosaari.fi/
> >
> >
> >
> >
> ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb@xxxxxxxxxxx <mailto:linux-dvb@xxxxxxxxxxx>
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
> --
> http://palosaari.fi/
>
>
> Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd
> Device Descriptor:
> bLength 18
> bDescriptorType 1
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> idVendor 0x1164 YUAN High-Tech Development Co., Ltd
> idProduct 0x1edc
> bcdDevice 1.00
> iManufacturer 1 YUANRD
> iProduct 2 STK7700D
> iSerial 3 0000000001
> bNumConfigurations 1
> Configuration Descriptor:
> bLength 9
> bDescriptorType 2
> wTotalLength 46
> bNumInterfaces 1
> bConfigurationValue 1
> iConfiguration 0
> bmAttributes 0xa0
> Remote Wakeup
> MaxPower 500mA
> Interface Descriptor:
> bLength 9
> bDescriptorType 4
> bInterfaceNumber 0
> bAlternateSetting 0
> bNumEndpoints 4
> bInterfaceClass 255 Vendor Specific Class
> bInterfaceSubClass 0
> bInterfaceProtocol 0
> iInterface 0
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x01 EP 1 OUT
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x81 EP 1 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x82 EP 2 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Endpoint Descriptor:
> bLength 7
> bDescriptorType 5
> bEndpointAddress 0x83 EP 3 IN
> bmAttributes 2
> Transfer Type Bulk
> Synch Type None
> Usage Type Data
> wMaxPacketSize 0x0200 1x 512 bytes
> bInterval 1
> Device Qualifier (for other device speed):
> bLength 10
> bDescriptorType 6
> bcdUSB 2.00
> bDeviceClass 0 (Defined at Interface level)
> bDeviceSubClass 0
> bDeviceProtocol 0
> bMaxPacketSize0 64
> bNumConfigurations 1
>
> Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5
> Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device
> using ehci_hcd and address 6
> Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen
> from 1 choice
> Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6
> different device-types
> Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> cold state, will try to load a firmware
> Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from
> file 'dvb-usb-dib0700-1.10.fw'
> Feb 18 23:50:55 localhost kernel: dib0700: firmware started
> successfully.
> Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> warm state.
> Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete
> MPEG2 transport stream to the software demuxer.
> Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan
> EC372S)
> Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0
> (DiBcom 7000PC)...
> Feb 18 23:50:56 localhost kernel: MT2266: successfully identified
> Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully
> initialized and connected.
> Feb 18 23:50:56 localhost kernel: usbcore: registered new interface
> driver dvb_usb_dib0700
>
> [crope@localhost linuxtv]$ scandvb fi-Oulu
> scanning fi-Oulu
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> initial transponder 634000000 0 2 9 3 1 2 0
> initial transponder 714000000 0 2 9 3 1 2 0
> initial transponder 738000000 0 2 9 3 1 2 0
> initial transponder 602000000 0 2 9 3 1 2 0
> >>> tune to:
> 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> >>> tune to:
> 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> WARNING: filter timeout pid 0x0011
> WARNING: filter timeout pid 0x0000
> WARNING: filter timeout pid 0x0010
> dumping lists (0 services)
> Done.
> [crope@localhost linuxtv]$
>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
--
http://palosaari.fi/
_______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
