Re: [PATCH] support Cinergy HT USB XE (0ccd:0058)

["Albert Comerma" <albert.comerma@xxxxxxxxx>]

For what I understand, changing the Firmware 64 to 60000200 changes the if frequency to 5.2MHz. So this modification on the firmware should make the card work. What it's more strange for me is that when trying to scan no signal or SNR is reported, so it seems like xc3028 firmware is not working properly. Perhaps could be a wrong BASE or DTV firmware loaded?

Albert

2008/2/16, Albert Comerma <albert.comerma@xxxxxxxxx>:

So, If it's not a problem, any of you could send me the current xc3028 firmware you are using, because mine does not seem to work... Thanks.

Albert

2008/2/15, Patrick Boettcher <patrick.boettcher@xxxxxxx>:

Aah now I remember that issue, in fact it is no issue. I was seeing that
problem when send the sleep command or any other firmware command without
having a firmware running. In was, so far, no problem.

Patrick.



On Fri, 15 Feb 2008, Holger Dehnhardt wrote:

> Hi Albert, Hi Mauro,
>
> I have successfulli patched and compiled the driver. Im using the terratec
> cinergy device and it works fine.
>
>>> [ 2251.856000] xc2028 4-0061: Error on line 1063: -5
>
> This error message looked very familar to me, so i searched my log and guess
> what I found:
>
> Feb 15 20:42:18 musik kernel: xc2028 3-0061: xc2028_sleep called
> Feb 15 20:42:18 musik kernel: xc2028 3-0061: xc2028_sleep called
> Feb 15 20:42:18 musik kernel: xc2028 3-0061: Error on line 1064: -5
> Feb 15 20:42:18 musik kernel: DiB7000P: setting output mode for demod df75e800
> to 0
> Feb 15 20:42:18 musik kernel: DiB7000P: setting output mode for demod df75e800
> to 0
>
> It identifies the marked line (just to be sure because of the differen line
> numbers)
>
>       if (priv->firm_version < 0x0202)
> ->            rc = send_seq(priv, {0x00, 0x08, 0x00, 0x00});
>       else
>               rc = send_seq(priv, {0x80, 0x08, 0x00, 0x00});
>
>> The above error is really weird. It seems to be related to something that
>> happened before xc2028, since firmware load didn't start on that point of
>> the code.
>
> The error really is weird, but it does not seem to cause the troubles - my
> card works despite the error!
>
>>
>>> [ 2289.284000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware
>>> version 2.7
>>
>> This message means that xc3028 firmware were successfully loaded and it is
>> running ok.
>
> This and the following messages look similar...
>
> Holger
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb