Am Donnerstag, den 14.02.2008, 02:00 +0100 schrieb Hartmut Hackmann: > Hi, folks > > In my personal repository: > http://linuxtv.org/hg/~hhackmann/v4l-dvb-experimental/ > you will find a driver that supports this card, DVB-T and DVB-S > > It might also work for > - one section of the MD8800 > - similar boards based on saa713x, tda10086, tda826x, isl6405 > > The board will show up as MD8800. According to Hermann, the configurations > for analog TV and DVB-T are identical. > If you want to use the board with DVB-S, you will need to load the > saa7134-dvb module with the option "use_frontend=1". The default 0 is > DVB-T. For those who got the board from a second source: don't forget > to connect the 12v (the floppy supply) connector. > > I don't have a dish, so i depend on your reports. To get the MD8800 > running, i need a volunteer who does the testing for me. He should be able > to apply patches, compile the driver and read kernel logs. > > Good luck > Hartmut > Hartmut, great job, thank you very much! Can't wait, result of a first voltage measurement on the md8800 Quad. The upper LNB connector associated to the second saa7134 16be:0008 device has correct voltage. Since my stuff is not in the original green PCI slot and I have only the first 16be:0007 device active, can't test much more for now here. People with the card in the original Medion PC could set "options saa7134-dvb use_frontend=1 debug=1" in /etc/modprobe.conf and then do "depmod -a". The Syntek v4l usb stkwebcam still produces a compilation error and needs to be disabled in "make xconfig" or something else. After "make" it is best to do "make rmmod" on top of your v4l-dvb-experimental first. Those new to the v4l-dvb development stuff might do also "make rminstall" and then check that no *.ko is left in /lib/modules/kernel_in_use/kernel/drivers/media/* Especially the old video_buf.ko in the video dir needs to be removed. Check with "ls -R |grep .ko" and then "make install". Now I suggest to "modprobe saa7134 card=117,96" In that case DVB-T is supported on the lower antenna connector and first adapter and DVB-S on the upper LNB connector and second adapter. Or to have it simple, it is safe to "make rmmod" and "modprobe saa7134 card=5,96 tuner=54,54" This way on the first device is only analog TV enabled, don't forget to use it first to have good DVB-T reception later anyway, and the only frontend is the DVB-S one in question for testing. On the CTX948 voltage is OK AND Tuning to: Camera Deputati / autocount: 22 Using DVB device 0:0 "Philips TDA10086 DVB-S" tuning DVB-S to 11804000 v 27500000 inv:2 fecH:2 DiSEqC: switch pos 0, 13V, hiband (index 2) DiSEqC: e0 10 38 f1 00 00 . LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 373 ms pipe opened xine pipe opened /root/.kaxtv.ts Asked to stop pipe closed Live stopped dvbstream::run() end dvbEvents 0:0 ended fdDvr closed Frontend closed Tuning to: Dubai Sports-1 / autocount: 23 Using DVB device 0:0 "Philips TDA10086 DVB-S" tuning DVB-S to 11747000 h 27500000 inv:2 fecH:3 DiSEqC: switch pos 0, 18V, hiband (index 3) DiSEqC: e0 10 38 f3 00 00 . LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 374 ms xine pipe opened /root/.kaxtv1.ts pipe opened Asked to stop pipe closed Live stopped dvbstream::run() end dvbEvents 0:0 ended fdDvr closed Frontend closed Tuning to: ARD "Das Erste" / autocount: 24 Using DVB device 0:0 "Philips TDA10086 DVB-S" tuning DVB-S to 11604000 h 27500000 inv:2 fecH:5 DiSEqC: switch pos 0, 18V, loband (index 1) DiSEqC: e0 10 38 f2 00 00 . LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 379 ms xine pipe opened /root/.kaxtv.ts pipe opened Asked to stop pipe closed Live stopped dvbstream::run() end dvbEvents 0:0 ended fdDvr closed Frontend closed Tuning to: Abu Dhabi Sport / autocount: 25 Using DVB device 0:0 "Philips TDA10086 DVB-S" tuning DVB-S to 12577000 h 27500000 inv:2 fecH:3 DiSEqC: switch pos 0, 18V, hiband (index 3) DiSEqC: e0 10 38 f3 00 00 . LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 379 ms xine pipe opened /root/.kaxtv1.ts pipe opened Asked to stop pipe closed Live stopped dvbstream::run() end dvbEvents 0:0 ended fdDvr closed Frontend closed Tuning to: BBC World / autocount: 26 Using DVB device 0:0 "Philips TDA10086 DVB-S" tuning DVB-S to 12596000 v 27500000 inv:2 fecH:3 DiSEqC: switch pos 0, 13V, hiband (index 2) DiSEqC: e0 10 38 f1 00 00 ... LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 560 ms pipe opened xine pipe opened /root/.kaxtv.ts pipe opened Asked to stop pipe closed Live stopped dvbstream::run() end dvbEvents 0:0 ended fdDvr closed Frontend closed Tuning to: All Music / autocount: 38 Using DVB device 0:0 "Philips TDA10086 DVB-S" tuning DVB-S to 10949000 v 27500000 inv:2 fecH:3 DiSEqC: switch pos 0, 13V, loband (index 0) DiSEqC: e0 10 38 f0 00 00 . LOCKED. NOUT: 1 dvbEvents 0:0 started Tuning delay: 378 ms xine pipe opened /root/.kaxtv.ts pipe opened Congratulations! Cheers, Hermann _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
