Hi, Am Donnerstag, den 14.02.2008, 12:01 +0100 schrieb hermann pitton: > Am Donnerstag, den 14.02.2008, 02:00 +0100 schrieb Hartmut Hackmann: > > Hi, folks > > > > In my personal repository: > > http://linuxtv.org/hg/~hhackmann/v4l-dvb-experimental/ > > you will find a driver that supports this card, DVB-T and DVB-S > > > > It might also work for > > - one section of the MD8800 > > - similar boards based on saa713x, tda10086, tda826x, isl6405 > > > > The board will show up as MD8800. According to Hermann, the configurations > > for analog TV and DVB-T are identical. > > If you want to use the board with DVB-S, you will need to load the > > saa7134-dvb module with the option "use_frontend=1". The default 0 is > > DVB-T. For those who got the board from a second source: don't forget > > to connect the 12v (the floppy supply) connector. > > > > I don't have a dish, so i depend on your reports. To get the MD8800 > > running, i need a volunteer who does the testing for me. He should be able > > to apply patches, compile the driver and read kernel logs. > > > > Good luck > > Hartmut > > > > Hartmut, > > great job, thank you very much! > > Can't wait, result of a first voltage measurement on the md8800 Quad. > > The upper LNB connector associated to the second saa7134 16be:0008 > device has correct voltage. > > Since my stuff is not in the original green PCI slot and I have only the > first 16be:0007 device active, can't test much more for now here. back on the machine and thinking about it twice ... The Quad works for me as well on the upper LNB connector, despite of that I previously used the lower one successfully with RF loopthrough from an external receiver. So, in case of the Quad, just let it be autodetected and try on the first adapter and upper LNB connector. Even more fun :) Cheers, Hermann > People with the card in the original Medion PC could set > "options saa7134-dvb use_frontend=1 debug=1" > in /etc/modprobe.conf and then do "depmod -a". > > The Syntek v4l usb stkwebcam still produces a compilation error and > needs to be disabled in "make xconfig" or something else. > > After "make" it is best to do "make rmmod" on top of your > v4l-dvb-experimental first. Those new to the v4l-dvb development stuff > might do also "make rminstall" and then check that no *.ko is left > in /lib/modules/kernel_in_use/kernel/drivers/media/* > Especially the old video_buf.ko in the video dir needs to be removed. > Check with "ls -R |grep .ko" and then "make install". > > Now I suggest to "modprobe saa7134 card=117,96" > In that case DVB-T is supported on the lower antenna connector and first > adapter and DVB-S on the upper LNB connector and second adapter. > > Or to have it simple, it is safe to "make rmmod" and > "modprobe saa7134 card=5,96 tuner=54,54" > This way on the first device is only analog TV enabled, don't forget to > use it first to have good DVB-T reception later anyway, and the only > frontend is the DVB-S one in question for testing. > > On the CTX948 voltage is OK > > AND > > Tuning to: Camera Deputati / autocount: 22 > Using DVB device 0:0 "Philips TDA10086 DVB-S" > tuning DVB-S to 11804000 v 27500000 > inv:2 fecH:2 > DiSEqC: switch pos 0, 13V, hiband (index 2) > DiSEqC: e0 10 38 f1 00 00 > . LOCKED. > NOUT: 1 > dvbEvents 0:0 started > Tuning delay: 373 ms > pipe opened > xine pipe opened /root/.kaxtv.ts > Asked to stop > pipe closed > Live stopped > dvbstream::run() end > dvbEvents 0:0 ended > fdDvr closed > Frontend closed > Tuning to: Dubai Sports-1 / autocount: 23 > Using DVB device 0:0 "Philips TDA10086 DVB-S" > tuning DVB-S to 11747000 h 27500000 > inv:2 fecH:3 > DiSEqC: switch pos 0, 18V, hiband (index 3) > DiSEqC: e0 10 38 f3 00 00 > . LOCKED. > NOUT: 1 > dvbEvents 0:0 started > Tuning delay: 374 ms > xine pipe opened /root/.kaxtv1.ts > pipe opened > Asked to stop > pipe closed > Live stopped > dvbstream::run() end > dvbEvents 0:0 ended > fdDvr closed > Frontend closed > Tuning to: ARD "Das Erste" / autocount: 24 > Using DVB device 0:0 "Philips TDA10086 DVB-S" > tuning DVB-S to 11604000 h 27500000 > inv:2 fecH:5 > DiSEqC: switch pos 0, 18V, loband (index 1) > DiSEqC: e0 10 38 f2 00 00 > . LOCKED. > NOUT: 1 > dvbEvents 0:0 started > Tuning delay: 379 ms > xine pipe opened /root/.kaxtv.ts > pipe opened > Asked to stop > pipe closed > Live stopped > dvbstream::run() end > dvbEvents 0:0 ended > fdDvr closed > Frontend closed > Tuning to: Abu Dhabi Sport / autocount: 25 > Using DVB device 0:0 "Philips TDA10086 DVB-S" > tuning DVB-S to 12577000 h 27500000 > inv:2 fecH:3 > DiSEqC: switch pos 0, 18V, hiband (index 3) > DiSEqC: e0 10 38 f3 00 00 > . LOCKED. > NOUT: 1 > dvbEvents 0:0 started > Tuning delay: 379 ms > xine pipe opened /root/.kaxtv1.ts > pipe opened > Asked to stop > pipe closed > Live stopped > dvbstream::run() end > dvbEvents 0:0 ended > fdDvr closed > Frontend closed > Tuning to: BBC World / autocount: 26 > Using DVB device 0:0 "Philips TDA10086 DVB-S" > tuning DVB-S to 12596000 v 27500000 > inv:2 fecH:3 > DiSEqC: switch pos 0, 13V, hiband (index 2) > DiSEqC: e0 10 38 f1 00 00 > ... LOCKED. > NOUT: 1 > dvbEvents 0:0 started > Tuning delay: 560 ms > pipe opened > xine pipe opened /root/.kaxtv.ts > > pipe opened > Asked to stop > pipe closed > Live stopped > dvbstream::run() end > dvbEvents 0:0 ended > fdDvr closed > Frontend closed > Tuning to: All Music / autocount: 38 > Using DVB device 0:0 "Philips TDA10086 DVB-S" > tuning DVB-S to 10949000 v 27500000 > inv:2 fecH:3 > DiSEqC: switch pos 0, 13V, loband (index 0) > DiSEqC: e0 10 38 f0 00 00 > . LOCKED. > NOUT: 1 > dvbEvents 0:0 started > Tuning delay: 378 ms > xine pipe opened /root/.kaxtv.ts > pipe opened > > Congratulations! > > Cheers, > Hermann > _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
